CRUX AMP-CH5 Handleiding

CRUX Niet gecategoriseerd AMP-CH5

Lees hieronder de 📖 handleiding in het Nederlandse voor CRUX AMP-CH5 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
AMP-CH5
OEM Amplier Replacement Interface for
Chrysler, Dodge, Jeep & RAM Vehicles with Uconnect Systems
R
INTERFACING SOLUTIONS
- Retains U-Connect and navigaon prompts.
- Retains Bluetooth handsfree mode.
- Allows adjustments for Balancing/Fading, Bass, Mid and Treble frequencies.
- Retains OEM radio EQ controls.
- Adjustable bass frequency and level. Includes an under dash mount encoder/bass knob.
- Provides 4 channel Front/Rear outputs plus non-fading subwoofer output.
- Remote output to turn on aermarket amplier.
- Includes an OEM amplier Bypass harness. No cung of factory wires.
PRODUCT FEATURES:
PARTS INCLUDED:
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
1 of 4 rev.092519
PRODUCT OVERVIEW:
The AMP-CH5 allows for an improvement in audio quality in vehicles equipped with data-bus controlled amplied
sound systems by upgrading to an aermarket mul-channel amplier while retaining the factory radio. The
AMP-CH5 provides balance, fader, bass, mid and treble frequency adjustments as well as a non-fading subwoofer
output for opmum sound staging.
NOTE:
AMP-CH5 Module AMP-CH5 Harness
OEM Amp Bypass Harness AMP-CH5 Encoder/Bass Knob
Audio from the factory backup sensors is not retained.
1. Carefully remove the trim bezel
around the radio and instrument
cluster. Use a plasc pry tool and go all
the way around the trim to pop up the
clips.
2. Remove the 4 screws holding
the screen.
3. Unplug the 52-pin connector
behind the screen.
6. Find a suitable locaon to mount
the aermarket amplier(s). You
will need to run the following to the
aermarket amplier:
1) Power wires from the baery
2) An amp turn-on wire and RCA
cables from the AMP-CH5 module.
3) Speaker wires from the OEM
amplier locaon. OEM amplier
locaon can vary by vehicle. On
sedans and trucks, it is usually
located on the le boom side of
the dashboard. On SUVs in the cargo
area. Make sure you have enough
length wires and RCA cables.
4. Plug the 52-pin connector to the
mang connector on the AMP-CH5
T-harness.
5. Plug the other end of the
AMP-CH5 T-harness to the OEM
screen.
7. On a 2017 Dodge Charger, the OEM
amplier is at the le boom side
of the dashboard. Remove the panel
above the pedals by removing the
panel clips.
8. Locate the OEM amplier and
unplug the connectors.
9. Connect the speakers wires from
the aermarket amplier to the Amp
Bypass harness included in the kit.
Mate the connectors into the OEM
amplier harness connectors.
R
INTERFACING SOLUTIONS
AMP-CH5
OEM Amplier Replacement Interface for
Chrysler, Dodge, Jeep & RAM Vehicles with Uconnect Systems
INSTALLATION INSTRUCTIONS:
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
2 of 4 rev.092519
R
INTERFACING SOLUTIONS
AMP-CH5
OEM Amplier Replacement Interface for
Chrysler, Dodge, Jeep & RAM Vehicles with Uconnect Systems
10. Plug the RCAs to the AMP-CH5
module.
11. Plug the 20-pin AMP-CH5
T-harness connector and the RJ11
encoder/bass knob connector to
the AMP-CH5 module.
12. Complete the connecons on the
aermarket amplier and mount the
amplier.
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
3 of 4 rev.092519
14. Encoder/Bass Knob Funcons:
- Press to turn ON/OFF Loudness funcon
- Turn to adjust subwoofer level
- Press and hold to enter programming mode
15. For vehicle specic wiring connecons of the OEM
Amp Bypass Harness, please visit
hps://www.cruxinterfacing.com/lisngs/amp-ch5/ or
scan the QR code:
13. Mount the encoder/bass knob to
the desired locaon.
R
INT ERFACIN G S OLUT ION S
Gold Series
To Vehicle
Harness
To Headunit
Aftermarket Amplier
22 Pin White
16 Pin Black
10 Pin Gray
To
OEM
Amplier
Harness
Encoder /
Bass Knob
Visit www.cruxinterfacing.com/????
for vehicle specic wiring instructions
of the OEM Amplier Bypass Harness
Front
Rear
Sub
Amp Turn On
(use to prevent turn on pop)
INSTALLATION DIAGRAM:

Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: AMP-CH5

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX AMP-CH5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd CRUX

CRUX

CRUX ACPLR-01 Handleiding

12 November 2024
CRUX

CRUX ACPMB-50W Handleiding

12 November 2024
CRUX

CRUX ACPBM-77Z Handleiding

12 November 2024
CRUX

CRUX ACPAD-81Y Handleiding

12 November 2024
CRUX

CRUX ACPAD-01 Handleiding

12 November 2024
CRUX

CRUX ACPBM-77X Handleiding

12 November 2024
CRUX

CRUX ACPLX-12XW Handleiding

12 November 2024
CRUX

CRUX ACPMB-45W Handleiding

12 November 2024
CRUX

CRUX ACPBM-77Y Handleiding

12 November 2024
CRUX

CRUX DKGM-16B Handleiding

5 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

NuPrime

NuPrime Pure AC-6 Handleiding

28 Januari 2025
Marklin

Marklin 7556 Handleiding

28 Januari 2025
Marklin

Marklin 78151 Handleiding

28 Januari 2025
Marklin

Marklin 7557 Handleiding

28 Januari 2025
Marklin

Marklin 72240 Handleiding

28 Januari 2025
Marklin

Marklin 5654 Handleiding

28 Januari 2025
Marklin

Marklin 59079 Handleiding

28 Januari 2025
Marklin

Marklin 73302 Handleiding

28 Januari 2025
Marklin

Marklin 7226 Handleiding

28 Januari 2025
Marklin

Marklin 72270 Handleiding

28 Januari 2025