Clas Ohlson ML520-11 Handleiding

Clas Ohlson Snijmachine ML520-11

Lees hieronder de 📖 handleiding in het Nederlandse voor Clas Ohlson ML520-11 (12 pagina's) in de categorie Snijmachine. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
EnglishSvenskaNorskSuomiDeut s ch
Art.no Model
30-9376 ML520-11 Ver. 20140505
Tile Cutter
Kakelskärare
Flisekutter
Laattaleikkuri
Fliesenschneider
2
English
Adjustable guide.
Cutting angle 0–60 degrees.
Tile Cutter
Art. no 30-9376
Please read the entire instruction manual before using and save it for future use.
We apologise for any text or photo errors and any changes of technical data.
If you have any questions concerning technical problems please contact our
Customer Service Department (see address on reverse.)
Presentation
• A tile cutter for professionals. It cuts and snaps in two simple steps.
• Magnesium alloy base plate with hardened metal scoring wheel.
Can produce square or angled cuts (0–60°).
• Max. cutting length 500 mm, max. tile thickness 16 mm.
3
English
Straight Cuts
Set the position of the cut with the guide.
Hold the tile firmly with one hand, and with
the other apply an even and moderate
pressure down on the handle while running
the scoring wheel across the glazed surface.
The scoring wheel should just cut the glaze.
Once the glaze has been scored it is time to
snap the tile. Place the tile, glazed surface
up, on the base plate. Position the score
just under the base plate’s centre line.
Rest the breaker-bar on the tile and close to
the guide and make sure that the breaker-bar
ends are equidistant from the score.
Gently apply pressure to the handle. Do not
use more force than necessary to snap the tile
along the score!
Important!
Make sure that the scoring wheel
does not touch the base plate when snapping
the tile. If you press too hard on the handle
while snapping the tile, the tile may break
unevenly and possibly crack into several pieces.
Angled Cuts
Angled cuts are carried out in generally in
the same way as straight cuts. The only
difference is that you must set the desired
angle before scoring the tile. Use the guide
ruler and fence. Loosen the wing nut,
adjust the angle and tighten the wing nut
again before scoring.
Important! Once again, make sure that
the scoring wheel does not touch the base
plate when snapping the tile.
Replacement of Scoring Wheel
Replacing the scoring wheel requires a posidrive,
screwdriver and a 10 mm spanner to loosen
the bolt and nut which hold the scoring wheel
in place.

Product specificaties

Merk: Clas Ohlson
Categorie: Snijmachine
Model: ML520-11

Heb je hulp nodig?

Als je hulp nodig hebt met Clas Ohlson ML520-11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Snijmachine Clas Ohlson

Clas Ohlson

Clas Ohlson ML520-11 Handleiding

28 April 2023

Handleiding Snijmachine

Nieuwste handleidingen voor Snijmachine

Livoo

Livoo MEN429 Handleiding

20 December 2024
Royal Catering

Royal Catering RCTC-5 Handleiding

17 December 2024
Royal Catering

Royal Catering RCGT-2 Handleiding

17 December 2024
Royal Catering

Royal Catering RCGS 155M Handleiding

17 December 2024
Gude

Gude GHF 800 Handleiding

8 December 2024
Toolland

Toolland PH360 Handleiding

7 December 2024
Boss

Boss Slicer SL-2 Handleiding

30 November 2024
Philco

Philco PHFS 6100 Handleiding

30 November 2024
Livoo

Livoo MEN435 Handleiding

20 November 2024
Cecotec

Cecotec Rock'nCut Advance Handleiding

20 November 2024