Logan Artist Elite 450-1 Handleiding

Logan Snijmachine Artist Elite 450-1

Lees hieronder de 📖 handleiding in het Nederlandse voor Logan Artist Elite 450-1 (8 pagina's) in de categorie Snijmachine. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
For best results use only
authentic Logan blades
INSTRUCTION MANUAL MODEL 450-1
ARTIST ELITE MAT CUTTER
INSTRUCTIONS AND OPERATION MANUAL
40 in (101 cm) mat cutting system with
bevel & straight cutters, production stops,
8 in (20 cm) squaring bar, 20 in (51 cm)
measuring bar & stop.
Uses Logan Replacement
Blade #270
L558DN5 Rev.5 6-16
Purchase Date
ID Number (on bottom of board)
Date (on bottom of board)
LoganGraphic.com
CAUTION!!
MAT CUTTING BLADES ARE SHARP
Artist Elite Mat Cutter
Instruction Manual Model 450-1
Logan Graphic Products Inc., 1100 Brown St reet, Wauconda, IL 60084 847-526-5515 LoganGraphic.com
2
Mat Guide
Used to set the border
width of a mat and
keep the mat in position
Identification of Machine Components
Cutting Board
Vinyl covered base
board of machine
Guide Rail
Used to guide cutting
heads while in use
Start and Stop Indicator
(not visible in this drawing -
located on opposite side) Line
which shows where to begin
and end cut
Blade Screw
Holds blade in
place for cutting.
Nylon Guides
Guides which allow Bevel
Cutting Head to hook
onto Guide Rail
Cutting Board
Bevel Cutting Head
Straight
Cutting Head
Blade Screw
Holds blade in
place inside
Blade Holder
Blade Cover
Covers blade
on Blade Holder
Measuring Bar
20 in (51 cm) removeable
scale & stop used to cut
matboard to size
Measuring Bar Stop
Blade Holder
Block which holds blade in place
while cutting. Has three separate
depth settings.
Slip Sheet
A Slip Sheet is a piece of
scrap mat board that is
placed beneath the mat
when bevel cutting
Left Right
Top
Fig. 1
2345678
9
10 11
12
13 14 1
5 16 17
18
19 20
1
Carton Contents
1. Straight Cutter
2. Bevel Cutter
3. Measuring Bar
4. Measuring Bar Stop
5. Squaring Bar
6. Mat Guide
7. Mat Guide Channels (2)
8. Channel Screws (2)
9. Rail Stops (2)
10. Screwdriver
11. Blade Pack
12. Squaring Bar Screws (2)
Bottom
Squaring Bar
1
2
3
4
11
6
7
8
10
9
12
Mat Guide Channel
Mat Guide Channel
5
Rail Stop
Congratulations on your purchase of the Logan Artist Elite Mat Cutter.
The Artist Elite is a well-designed mat cutter, combining the best of what Logan mat cutters have to offer. Features like heavy duty pull style bevel
cutter with anti-crawl pin, pivot & pull straight cutter, production stops, squaring bar, removable measuring bar with stop, parallel mat guide, plus
the flexibility to add additional accessories like the glass cutter or surface V-groovers make the Artist Elite a cost effective and useful tool for artists,
crafters, photographers and framers. This instruction manual is written to familiarize you with the product. Please take some time to review the
instructions before cutting. You will find that the time taken will be well worth it, and you will be cutting professional mats in no time.
PRODUCT DESCRIPTION
450-1 Artist Elite- 40 in vinyl covered cutting board with mat guide in aluminum channels, two production stops, 20in measuring bar, measuring bar
stop, 8 in squaring bar, straight and bevel cutting heads, slip sheet, screwdriver and one 5-pack of Logan #270 blades.
Orientation
The procedures detailed in the
following instructions refer to the
right & left sides and top & bottom
of the machine as shown (Fig. 1).
Artist Elite Mat Cutter
Instruction Manual Model 450-1
Logan Graphic Products Inc., 1100 Brown St reet, Wauconda, IL 60084 847-526-5515 LoganGraphic.com
3
Blade Installation
1. Loosen blade retaining screw enough to allow blade holder to tilt back
(Fig. 2). Loosen the blade holding knob.
2. Remove one blade from the package of five.
NOTE: Because the blades are packed with a small amount of oil, they may stick
together. Be certain that only one blade is being inserted into the blade slot.
3. Slide blade, sharp edge down, fully into blade holder (Fig. 3).
NOTE: The hole in the blade is not designed to line up with the blade screw.
4. Tighten blade screw.
5. Tilt blade holder down, allowing tip of blade to enter into the blade slot
6. Retighten retaining screw (Fig. 4).
Blade Installation - Model 701-1 Straight Cutter Elite
1. Remove blade knob and blade cover.
2. Align blade hole over thread. Be sure sharp edge of blade is facing down.
3. Reassemble blade cover and blade knob.
NOTE: Adjust blade to foamboard (fully extended), standard 4-ply mat board
(middle setting) or safety (fully retracted) (Fig. 5).
Mat Guide Assembly
1. Press each Mat Guide Channel into board slots with rounded end towards
guiderail.
2. Insert two channel screws from the UNDERSIDE of board and tighten (Fig. 6).
3. Loosen each mat guide knob three full turns.
4. Hold mat guide at ends with your thumbs on the loosened knobs with
raised edge facing guiderail and evenly drop mat guide into channels.
5. Slide to adjust and tighten knobs to lock mat guide (Fig. 7).
Fig. 2
Fig. 3
Fig. 5
Fig. 4
Fig. 7Fig. 6
CAUTION!!
MAT CUTTING BLADES ARE SHARP

Product specificaties

Merk: Logan
Categorie: Snijmachine
Model: Artist Elite 450-1

Heb je hulp nodig?

Als je hulp nodig hebt met Logan Artist Elite 450-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Snijmachine Logan

Logan

Logan Artist Elite 450-1 Handleiding

26 Maart 2025
Logan

Logan 350-1 Handleiding

26 Maart 2025

Handleiding Snijmachine

Nieuwste handleidingen voor Snijmachine

Royal Catering

Royal Catering RCGT-1 Handleiding

30 Januari 2025
Livoo

Livoo MEN429 Handleiding

20 December 2024
Royal Catering

Royal Catering RCTC-5 Handleiding

17 December 2024
Royal Catering

Royal Catering RCGT-2 Handleiding

17 December 2024
Royal Catering

Royal Catering RCGS 155M Handleiding

17 December 2024
Gude

Gude GHF 800 Handleiding

8 December 2024
Toolland

Toolland PH360 Handleiding

7 December 2024
Boss

Boss Slicer SL-2 Handleiding

30 November 2024
Philco

Philco PHFS 6100 Handleiding

30 November 2024
Livoo

Livoo MEN435 Handleiding

20 November 2024