Cisco Aironet 6021 Handleiding

Cisco Access point Aironet 6021

Lees hieronder de 📖 handleiding in het Nederlandse voor Cisco Aironet 6021 (31 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/31
Aironet 600 Series OceExtend Access Point
Conguration Guide
Document ID: 113003
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Background Information
Setup Guidelines
Oce Extend Solution Overview
Firewall Conguration Guidelines
Oce Extend AP−600 Conguration Steps
WLAN and Remote LAN Conguration Settings
WLAN Security Settings
MAC Filtering
Supported User Count
Channel Management and Settings
Additional Caveats
OEAP−600 Access Point Conguration
OEAP−600 Access Point Hardware Installation
Troubleshooting the OEAP−600
How to debug client association issues
How to interpret the event log
When the Internet connection appears unreliable
Additional debug Commands
Known Issues/Caveat
Related Information
Introduction
This document provides information on the requirements to congure a Cisco Wireless LAN (WLAN)
Controller for use with the Cisco Aironet® 600 Series OceExtend Access Point (OEAP). The Cisco Aironet
600 Series OEAP supports split mode operation and it has facilities that require conguration through the
WLAN Controller and features that can be congured locally by the end user. This document also provides
information about the congurations necessary for proper connection and supported feature sets.
Prerequisites
Requirements
There are no specic requirements for this document.
Components Used
The information in this document is based on the Cisco Aironet 600 Series OceExtend Access Point
(OEAP).
The information in this document was created from the devices in a specic lab environment. All of the
devices used in this document started with a cleared (default) conguration. If your network is live, make sure
that you understand the potential impact of any command.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Background Information
Setup Guidelines
The Cisco Aironet 600 Series OEAP is supported on these controllers: Cisco 5508, WiSM−2 and the
Cisco 2504.
The rst controller release that supports Cisco Aironet 600 Series OEAP is 7.0.116.0
The controllers Management Interfaces need to be on a routable IP network.
Corporate Firewall conguration needs to be changed to allow trac with UDP port numbers 5246
and . 5247
Oce Extend Solution Overview
A user is given an access point (AP) primed with the IP address of the corporate controller, or the user
can enter the IP address of the controller from the conguration screen (setup HTML pages).
The user plugs the AP to their home router.
The AP gets an IP address from their home router, joins the primed controller and creates a secured
tunnel.
Cisco Aironet 600 Series OEAP then advertises the corporate SSID, which extends the same security
methods and services across the WAN to the users home.
If the remote LAN is congured, one wired port on the AP is tunneled back to the controller.
The user can then enable additionally a local SSID for personal use.
Firewall Conguration Guidelines
The general conguration on the rewall is to allow CAPWAP control and CAPWAP management port
numbers through the rewall. The Cisco Aironet 600 Series OEAP controller can be placed in the DMZ zone.
Note: 5246 5247The UDP and ports need to be opened on the rewall between the WLAN controller and the
Cisco Aironet 600 Series OEAP.
This diagram shows an Cisco Aironet 600 Series OEAP controller on the DMZ:
Here is a sample rewall conguration:
interface Ethernet0/0
nameif outside
security−level 0
ip address X.X.X.X 255.255.255.224
!−−− X.X.X.X represents a public IP address
!
interface Ethernet0/2
nameif dmz
security−level 50
ip address 172.16.1.2 255.255.255.0
!
access−list Outside extended permit udp any host X.X.X.Y eq 5246
!−−− Public reachable IP of corporate controller
access−list Outside extended permit udp any host X.X.X.Y eq 5247
!−−− Public reachable IP of corporate controller
access−list Outside extended permit icmp any any
!
global (outside) 1 interface
nat (dmz) 1 172.16.1.0 255.255.255.0
static (dmz,outside) X.X.X.Y 172.16.1.25 netmask 255.255.255.255
access−group Outside in interface outside
In order to transmit the internal AP−Manager IP address to the OceExtend AP as part of the CAPWAPP
Discovery Response packet, the controller administrator needs to make sure that NAT is enabled in the
AP−Manager interface and the correct NATed IP address is sent to the AP.
Note: By default, the WLC will only respond with the NAT IP address during AP Discovery when NAT is
enabled. If APs exist on the inside and outside of the NAT gateway, issue this command in order to set the
WLC to respond with both the NAT IP address and Non−NAT (inside) Management IP address:
cong network ap−discovery nat−ip−only disable


Product specificaties

Merk: Cisco
Categorie: Access point
Model: Aironet 6021

Heb je hulp nodig?

Als je hulp nodig hebt met Cisco Aironet 6021 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Access point Cisco

Handleiding Access point

Nieuwste handleidingen voor Access point