Cisco Aironet 2600i Handleiding

Cisco Access point Aironet 2600i

Lees hieronder de 📖 handleiding in het Nederlandse voor Cisco Aironet 2600i (40 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

G ETTING S GTARTED UIDE

Cisco Aironet 2600 Series Access Points

July, 2012

P/N: 78-20842-01

1About this Guide

2Introduction to the Access Point

3Safety Instructions

4Unpacking

5Configurations

6Access Point Ports and Connectors

7Configuring the Access Point

8Mounting the Access Point

9Deploying the Access Point on the Wireless Network

10 Troubleshooting

11 Declarations of Conformity and Regulatory Information

12 Configuring DHCP Option 43 and DHCP Option 60

13 Access Point Specifications

1 About this Guide

This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series

Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point in this

document.

2 Introduction to the Access Point

The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream

rates over a deployable distance with high reliability when serving clients. The 2600 series provides

high reliability and overall wireless performance.

The 2600 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna

options. The access points support full inter-operability with leading 802.11n clients, and support a

mixed deployment with other access points and controllers.

The 2600 series access point is available in both controller-based (Unified) and standalone

(Autonomous) configurations and supports:

•Simultaneous single-band or dual-band (2.4 GHz/5 GHz) radios

•Integrated antennas on 2602I access point models (AIR-CAP2602I-x-K9)

•External antennas for rugged 2602E access point models (AIR-CAP2602E-x-K9)

Note The ‘x’ in the model numbers represents the regulatory domain. Refer to “Regulatory

Domains” section on page 6 for a list of supported regulatory domains.

The features of the 2600 series are:

•Processing sub-systems (including CPUs and memory) and radio hardware which supports:

–

Network management

–

CleanAir—Automatic detection, classification, location and mitigation of RF interference

(not available on autonomous or standalone models)

–

ClientLink 2.0—BeamForming to 802.11n clients as well as legacy 802.11a/g OFDM clients

–

VideoStream

–

Location

–

WIDS/WIPS

–

Security

–

Radio Resource Management (RRM)

–

Rogue detection

–

Management Frame Protection (MFP)

–

Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps

data-rates

•32 MB flash size

•802.11af/at

–

CDP (Cisco Discovery Protocol)

•2.4 GHz and 5 GHz 802.11n radios with the following features:

–

3TX x 4RX

–

3-spatial streams, 450 Mbps PHY rate

–

Spectrum intelligence

–

DPD (Digital Pre-Distortion) technology

–

Cisco Vector Beamforming—Implicit Co-phase beamforming for .11ag clients and 1

spatial-stream and 2 spatial-stream clients

–

Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Product specificaties

Merk:	Cisco
Categorie:	Access point
Model:	Aironet 2600i
Kleur van het product:	Wit
Gewicht:	1040 g
Breedte:	221 mm
Diepte:	54 mm
Hoogte:	221 mm
LED-indicatoren:	Ja
Plaatsing:	Ceiling, Wall
Frequentieband:	2.412 - 2.472, 5.745 - 5.825 GHz
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	UL 60950-1\nCAN/CSA-C22.2 No. 60950-1\nUL 2043\nIEC 60950-1\nEN 60950-1\nEN 50155
Intern geheugen:	256 MB
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.11a, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3u
Ondersteunde beveiligingsalgoritmen:	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-SIM, EAP-TLS, EAP-TTLS, MSCHAPv2, TKIP, WPA, WPA2
Soort antenne:	Intern
Antenne versterkingsniveau (max):	4 dBi
Temperatuur bij opslag:	-30 - 70 °C
Intern:	Nee
Draadloos LAN data-overdrachtsnelheid (max):	450 Mbit/s
Flash memory:	32 MB
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 4572 m
Maximale overdrachtssnelheid van gegevens:	1000 Mbit/s
2,4 GHz:	Ja
5 GHz:	Ja
Wifi Multimedia (WMM)/(WME):	Ja
Power over Ethernet (PoE):	Ja
Antennefuncties:	Ingebouwde antenne
Aantal kanalen:	18 kanalen
AC-ingangsspanning:	44 - 57 V
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent