Chef's Choice Diamond Hone Sharpener 310 Handleiding
Chef's Choice
Messenslijper
Diamond Hone Sharpener 310
Lees hieronder de 📖 handleiding in het Nederlandse voor Chef's Choice Diamond Hone Sharpener 310 (5 pagina's) in de categorie Messenslijper. Deze handleiding was nuttig voor 79 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/5
MODEL 310 INSTRUCTIONS
Diamond Hone®Sharpener
Read these instructions before use.
It is essential that you follow these
instructions to achieve optimum results.
© 2010 EdgeCraft Corp.
2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed including the following:
1. Read all instructions.
2. To protect against electrical hazards, do not immerse the Chef’sChoice
®in water or
other liquid.
3. Make sure that only clean knife blades are inserted in the Chef’sChoice
®.
4. Unplug from outlet when not in use, before putting on or taking off parts and
before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner.
U.S. Customers: You can return your sharpener to EdgeCraft’s factory for service where
the cost of repair or electrical or mechanical adjustment can be estimated. When the
electrical cord on this appliance is damaged, it must be replaced by the Chef’sChoice
distributor or other qualified service to avoid the danger of electrical shock.
Outside U.S.: Please return your sharpener to your local distributor where the cost of repair
or electrical or mechanical adjustment can be estimated. If the supply cord of this appli-
ance is damaged, it must be replaced by a repair facility appointed by the manufac-
turer because special tools are required. Please consult your Chef’sChoice distributor.
7. CAUTION! This appliance may be fitted with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not modify the plug in anyway.
8. The use of attachments not recommended or sold by EdgeCraft Corporation may
cause fire, electric shock or injury.
9. The Chef’sChoice®Model 310 is designed to sharpen kitchen knives, pocket knives
and most sport knives. Do not attempt to sharpen scissors, ax blades or any blade that
does not fit freely in the slots.
10.Do not let the cord hang over edge of table or counter or touch hot surfaces.
11.When in the “ON” position, the Chef’sChoice®should always be on a stable countertop
or table.
12.WARNING: KNIVES PROPERLY SHARPENED ON YOUR CHEF’SCHOICE®WILL BE
SHARPER THAN YOU EXPECT. TO AVOID INJURY, USE AND HANDLE THEM WITH
EXTREME CARE. DO NOT CUT TOWARD ANY PART OF YOUR FINGERS, HAND OR BODY.
DO NOT RUN FINGER ALONG EDGE. STORE IN A SAFE MANNER.
13.Do not use outdoors.
14.Close supervision is necessary when any appliance is used by or near children.
15.Do not use honing oils, water or any other lubricant with the Chef’sChoice
®.
16.For household use only.
Press the switch, on the lower right front
GETTING TO KNOW YOUR SHARPENER
Before using your sharpener you may wish to become familiar with its features.
1. Place Chef’sChoice®Diamond Hone®Sharpener on a level table or kitchen counter surface.
Do not plug the sharpener cord into an outlet.
2. (Refer to Figures 1 and 2). Pick up a kitchen knife and place the heel area of the knife blade
in any of the sharpening slots. Loosen your grip. You will notice that the knife will be pulled
to the side of the slot and into the slot by a magnet.
3. Now, while holding the knife with a secure yet relatively loose grip as in Figure 4, pull the
knife blade towards you while allowing the knife blade to lie against the magnet. Let the
magnet establish the blade angle. Except when sharpening the tip, keep the knife blade
level with the table.
“BREAKING-IN” YOUR KNIFE
When sharpening a knife for the first time with Chef’sChoice
®, it is necessary first to
reangle the factory edge– a process called “Breaking-in” your knife. For each knife this is a
one-time operation.
Because factory edge angles vary widely, it is essential that the initial sharpening in Stage 1 be
sufficient to completely reangle the factory edge. This takes extra time. However, once this
“Break-in” process is complete a knife can be resharpened very quickly.
Place the Chef’sChoice®on a sturdy table or counter. Plug the sharpener cord into an
appropriate electric outlet.
4
Figure 1. Chef’sChoice®Model 310. Figure 2. Typical kitchen knife.
Handle
Tip Edge
Heel
Bolster
Sharpening Slots:
On/Off
Switch
Honing Slots:
Left
Right Left
Right
Stage 1 Sharpening
(Orbiting Diamonds®)
Stage 2 Honing
(Orbiting Diamonds®)
Figure 3. Magnets control the blade angle. Figure 4. You will find it easier to use a loose grip.
Proper speed, correct sharpening grip
1… 2… 3 seconds, keep knife level
Product specificaties
| Merk: | Chef's Choice |
| Categorie: | Messenslijper |
| Model: | Diamond Hone Sharpener 310 |
Heb je hulp nodig?
Als je hulp nodig hebt met Chef's Choice Diamond Hone Sharpener 310 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Messenslijper Chef's Choice
8 Januari 2024
8 Januari 2024
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
Handleiding Messenslijper
- Messenslijper IKEA
- Messenslijper Krups
- Messenslijper Adler
- Messenslijper Ambiano
- Messenslijper Bartscher
- Messenslijper Beper
- Messenslijper Berkel
- Messenslijper Bifinett
- Messenslijper Blokker
- Messenslijper Bomann
- Messenslijper Domo
- Messenslijper EdgeCraft
- Messenslijper Fagor
- Messenslijper Gardenline
- Messenslijper Gastroback
- Messenslijper Gourmetmaxx
- Messenslijper Graef
- Messenslijper Gude
- Messenslijper Melissa
- Messenslijper Powerplus
- Messenslijper Presto
- Messenslijper Princess
- Messenslijper Roadstar
- Messenslijper Salter
- Messenslijper Silvercrest
- Messenslijper Sogo
- Messenslijper Steba
- Messenslijper Studio
- Messenslijper Tower
- Messenslijper Trebs
- Messenslijper Ozito
- Messenslijper Clatronic
- Messenslijper Guzzanti
- Messenslijper OBH Nordica
- Messenslijper Orbegozo
- Messenslijper Tacklife
- Messenslijper Eldom
- Messenslijper Waring Commercial
- Messenslijper Brentwood
- Messenslijper Herkules
- Messenslijper Genie
- Messenslijper C3
- Messenslijper Orava
- Messenslijper Alpha Tools
- Messenslijper For_Q
- Messenslijper Wüsthof
- Messenslijper Work Sharp
- Messenslijper Petra Electric
- Messenslijper GARDE
- Messenslijper IdeenWelt
- Messenslijper Donau Elektronik
- Messenslijper Sharpal
Nieuwste handleidingen voor Messenslijper
17 November 2024
17 November 2024
16 November 2024
5 September 2024
15 Augustus 2024
15 Augustus 2024
15 Augustus 2024
8 Augustus 2024
9 Juli 2024
18 Mei 2024