Celestron Thermistor 94037 Handleiding

Celestron Niet gecategoriseerd Thermistor 94037

Lees hieronder de 📖 handleiding in het Nederlandse voor Celestron Thermistor 94037 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
The Thermistor for Smart DewHeater Controllers is required for automatic
“smart control” of a non-Celestron heating band or heating strip with the
Celestron Smart DewHeater Controllers. The thermistor allows the controller
to detect how much heat the heating band is applying to the telescope.
Along with the controller’s integrated environmental sensor, the thermistor
helps determine how much power the heating band needs to keep the
optics free from dew. This system provides the most efficient power usage
for dew prevention, greatly extending battery life. If you choose not to use
the thermistor, you can only set the heating band power manually. If you are
using a Celestron Dew Heater Ring, this thermistor assembly is not required,
as the ring already has a built-in thermistor.
If you are using another manufacturer’s heating band or strip, it needs an
RCA-type plug to connect to the controller’s heater output ports. Connect
the heating band to the telescope and connect its plug to one of the
controller’s dew heater ports. Then, place the tip of the probe thermistor
under the heating band (Figure 1). We suggest using tape to secure it firmly
in place.
THERMISTOR FOR
SMART DEWHE ATER
CONTROLLERS
# 94037
INS T RU CT I O N MANUAL
Fig. 1: Place the thermistor under the heating band so that it is secure.
ENGLISH
Fig. 2: Connect the thermistor’s plug to the thermistor port corresponding to the dew heater port
you are using on the controller
SPECIFICATIONS: Thermistor plug: 2.5mm Audio
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. T hese limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, t he user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/T V technician for help.
This device complies with part 15 of the FCC Rules. Operat ion is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Product design and specifications are subject to change without prior notification. This product is designed and intended for use by those 14 years of age and older.
©2022 Celestron. Celestron and Symbol are trademarks
of Celestron, LLC. All rights reserved. Celestron.com
2835 Columbia Street, Torrance, CA 90503 USA
This product is designed and intended for use by those 14
years of age and older.
Made in China
celestron.com/pages/warranty
Connect the thermistor’s plug to the thermistor port corresponding to the
dew heater port you are using on the controller (Figure 2). Once the thermistor
is connected, the controller will automatically adjust the power to the heating
band based on the data from the thermistor and the controller’s environmental
sensor.
Each dew heater port on the controller can deliver a maximum of 84W power
(7A max current), which should be more than enough for most dew heating
bands or strips. For more information about automatic “smart control” of
a dew heater, refer to the instruction manual included with your Celestron
Smart DewHeater Controller.
11-22
La thermistance pour les contrôleurs Smart DewHeater est requise pour
le « contrôle intelligent » d’un anneau ou d'une bande chauffante par les
contrôleurs Smart DewHeater de Celestron. La thermistance permet
au contrôleur de détecter la quantité de chaleur délivrée par la bande
chauffante au télescope. Avec le capteur environnemental intégré au
contrôleur, la thermistance aide à déterminer de combien de puissance
la bande chauffante doit disposer pour que les optiques restent libres de
rosée. Le système permet l’utilisation de l’énergie la plus efficace pour la
prévention de la rosée, améliorant grandement l’autonomie de la batterie. Si
vous décidez de ne pas utiliser la thermistance, alors vous ne pouvez définir
la puissance de la bande chauffante que manuellement. Si vous utilisez un
Anneau Dew Heater de Celestron, cet assemblage de thermistance n’est
pas obligatoire, car l’anneau en est déjà équipé.
Si vous utilisez une bande ou une languette chauffante de marque autre que
Celestron, elle aura besoin d'une prise de type RCA pour connecter aux
ports de sortie de chauffage du contrôleur. Connectez la bande chauffante
au télescope et connectez sa fiche à l'un des ports du chauffage du
contrôleur anti-buée. Placez ensuite la sonde de la thermistance sous la
bande chauffante ( ). Nous vous suggérons d’utiliser du ruban adhésif Figure 1
pour la tenir fermement en place.
THERMISTANCE
POUR LES
CONTRÔLEURS
SMART DEWHEATER
# 94037
MODE D'EMPLOI
Fig. 1: Placez la thermistance sous la bande chauffante de manière à la fixer.
FRANÇAIS

Product specificaties

Merk: Celestron
Categorie: Niet gecategoriseerd
Model: Thermistor 94037

Heb je hulp nodig?

Als je hulp nodig hebt met Celestron Thermistor 94037 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Celestron

Celestron

Celestron Smart DewHeater and Controller 2x Handleiding

30 Juli 2024
Celestron

Celestron Thermistor 94037 Handleiding

30 Juli 2024
Celestron

Celestron StarPointer Finderscope Handleiding

23 Juni 2024
Celestron

Celestron OMNI AZ 102 Handleiding

5 Juli 2023
Celestron

Celestron StarSense Explorer 10 Handleiding

2 Juli 2023
Celestron

Celestron PowerTank 18763 Handleiding

17 Juni 2023
Celestron

Celestron EclipSmart Handleiding

15 Juni 2023
Celestron

Celestron PowerSeeker Handleiding

25 Mei 2023
Celestron

Celestron CGX Equatorial 1100 HD Handleiding

23 Mei 2023
Celestron

Celestron Popular Sience Travel Scope 70 Handleiding

30 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-HTSS Handleiding

21 December 2024