Celestron Smart DewHeater and Controller 2x Handleiding

Celestron Niet gecategoriseerd Smart DewHeater and Controller 2x

Lees hieronder de 📖 handleiding in het Nederlandse voor Celestron Smart DewHeater and Controller 2x (17 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/17

ENGLISH | 1

Congratulations on purchasing the Celestron Smart DewHeater

and Controller 2x. This controller delivers “smart” and efficient

power usage for up to two of your telescope system’s dew

heaters plus another 12V DC device—while also providing cable

management for your setup. When you plug your dew heaters

into the controller, one cable connects everything to your power

source, while another connects the setup to your PC, if desired.

If you prefer not to connect to a PC, simply plug your dew heaters

into the controller and power it on. The controller will automatically

monitor the ambient temperature and humidity using its integrated

environmental sensor. The thermistor port monitors the lens’s

temperature and provides only enough power to prevent dew.

If you’re using battery power, this “smart” system significantly

reduces the heaters’ power consumption, extending battery life. If

you would like to manually adjust settings or monitor data, connect

to a PC or your Celestron mount’s hand control.

1. Parts List

2. Controller Overview

TABLE OF CONTENTS

Fig 1 – All included items

Refer to Figure 2 for an overview of the input jacks, output ports, and

features of the Smart DewHeater Controller 2x.

If you are missing any parts in the Parts List, please contact Celestron

Technical Support at www.celestron.com/pages/technical-support

for assistance.

1. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pg.1

2. Controller Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pg.1

3. Mounting the Controller to Your Setup . . . . . . . . . . . . . . . . . . Pg.3

4. Powering the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pg.4

5. Connecting to a Celestron Mount . . . . . . . . . . . . . . . . . . . . . . Pg.5

6. Using the Controller with a Celestron Hand Control . . . . . . . . Pg.5

7. Connecting to a PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pg.6

8. Using the Controller with CPWI Software . . . . . . . . . . . . . . . Pg.7

9. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pg.10

Appendix A:

Determining Power Supply Requirement Examples . . . . . . . . . Pg.11

SMART DEWHEATER AND CONTROLLER 2X

INSTRUCTION MANUAL

Model #94035

ENGLISH

1. 2.

Fig 2-1

Fig 2-2

Fig 2-3

5. 4.

1. Smart DewHeater Controller 2x

2. Power cable

3. Auxilliry cable

4. Mount power cable

5. Tripod leg strap

6. Thermistor Cable

1. Dew heater ports

2. Power input jack

3. Thermistor ports

4. AUX ports

5. PC port

6. Power output port

7. Bridge

2 | ENGLISH

DEW HEATER CONTROL

The Smart DewHeater Controller 2x provides automatic “smart”

control for up to two dew heater rings or dew heater bands/strips.

If you are using the controller with a Celestron Dew Heater Ring,

connect the ring’s power input jack to one of the controller’s dew

heater output ports using the extension cable that comes with the

ring. Next, plug the included thermistor cable into the ring’s thermistor

jack and the corresponding thermistor port on the controller. (Figure

3) The thermistor indicates the Schmidt corrector lens’s temperature.

The controller uses this data along with information from the

controller’s integrated environment sensor (i.e., ambient temperature

and humidity) to provide just the right amount of power to the ring

to prevent dew. If you are using battery power, this system greatly

increases battery life under most conditions. Once you connect the

ring to one of the controller’s dew heater ports, it will begin to heat up

(unless the port has been manually disabled, which will be discussed

later in this manual).

You will need an additional thermistor cable if you wish to use

automatic smart control for more than one Celestron Dew Heater

Ring. The thermistor cable is a standard 2.5mm audio cable, which

you can find at most electronics retailers. Be sure to get one that is

long enough to accommodate your setup.

The controller’s environmental sensor resides in the “bridge” on the

controller’s enclosure (Figure 2). This location protects the sensor

from any heat radiating from the enclosure while still providing good

airflow. An integrated environmental sensor gives you a simpler,

cleaner setup without dangling external sensors to get in your way.

Occasionally, you should recalibrate the environmental sensor.

Recalibrating heats the sensor so that any accumulated moisture

evaporates, ensuring the most accurate temperature and humidity

data and the most efficient power use. We recommend recalibrating

before initial use and after long periods of storage in humid conditions.

The process is easy; we’ll explain it later in this manual.

If you do not wish to use automatic smart control, you can manually

set the power for each of the dew heater ports from 0% (off) to

100% (full power). We’ll discuss this option in more detail later in

the manual.

If you are using a non-Celestron heating band or strip, it will need an

RCA-type plug to connect to the controller’s heater output ports. You

have two options for controlling third party bands/strips:

1. You can purchase the optional Thermistor for Celestron Smart

DewHeater Controllers to provide automatic smart power control.

Connect the heating band to the telescope and connect its plug

to one of the dew heater ports. Then, place the tip of the probe

thermistor under the heating band so it is secure (you may want

to use tape). Connect the thermistor’s plug to the corresponding

jack on the controller (Figure 4). The probe thermistor is not as

accurate as the Celestron Dew Heater Ring’s built-in thermistor,

which contacts the corrector lens directly. Still, it allows for

automatic smart control of heating bands/strips.

2. Alternatively, you can manually set the power output for each dew

heater port from 0% to 100%, as mentioned previously.

Each of the dew heater ports can deliver a maximum of 84W power

(7A max current), which should be more than enough for most dew

heaters. If a connected dew heater draws more than 84W, the port

will automatically shut off to protect the circuitry. After reducing the

load, you can re-enable the port, a process that we’ll discuss later in

this manual

POWER CONTROL

A handy feature of the Smart DewHeater Controller 2x is its ability to

provide 12V DC power to an external device. Many users choose to

power their mount this way, enabling them to run their dew heaters

and mount from a single power source.

To power a 12V DC device, use the included mount power cable—

the cable with 12V DC barrel connectors on both ends (Figure 1).

Simply connect the device’s power input to the controller’s 12V DC

power output port. The port requires a 12V DC 5.5mm/2.1mm tip

positive barrel connector. One end of the mount power cable has an

integrated nut on its barrel connector. You can thread this onto the

power jack on Celestron mounts with a threaded barrel connector

for the most secure connection. Power will flow through the port as

soon as you connect the device; there is no need to turn the port on

(unless you disabled the port previously, which we’ll discuss later).

Fig 3

Connect a Celestron Dew Heater Ring to the controller using the extension cable that comes

with the ring and the thermistor cable that comes with the controller.

Fig 4

If you are using a heating band or strip from another manufacturer, you will need the

optional Celestron Thermistor for Smart DewHeater Controllers.

Celestron Thermistor

Extension cable

Thermistor cable

ENGLISH | 3

CG-5/Vixen or CGE/Losmandy dovetail bar. If you have a dovetail

bar on your optical tube, this is perhaps the easiest and most

convenient way to connect the controller to your setup. Simply

loosen the controller’s clamping knobs, place the controller’s

clamps onto the dovetail rail, and then firmly tighten the clamping

knobs (Figure 5).

- Use the included tripod leg strap to attach the controller to one of

your tripod’s legs. Insert the strap through the slots in the bottom of

the controller’s enclosure, wrap the strap around one of the tripod

legs, tighten the strap with the buckle, and secure the strap end to

itself with the hook-and-loop fasteners on the strap (Figure 6).

- If your tripod’s accessory tray is large enough, you can place the

controller on the tray. If you choose this method, keep in mind that

the controller will not be secured in place. Be careful to avoid

forceful cable pulls.

NOTE: DO NOT PLACE THE CONTROLLER ON THE GROUND!

Water and dirt can potentially enter the controller and may cause

electrical problems.

USING THE BRIDGE FOR CABLE MANAGEMENT

The bridge on the enclosure houses the controller’s environmental

sensor, isolating it from radiant heat to provide the most accurate

ambient temperature and humidity data. We also designed the bridge

to help with cable management. You can run cables underneath the

The power port can deliver a maximum of 84W power (7A max

current). If a connected device draws more than 84W, the port will

automatically shut off to protect the circuitry. After reducing the load,

you can re-enable the port, a process that we’ll discuss later.

STATUS LEDS

There are three LEDs on the bridge that indicate the controller’s

status:

- The middle LED indicates whether power is flowing to the controller.

- The LED labeled “Over Current” illuminates if the current draw is

greater than the power source can provide. If this happens, either

disconnect or reduce power to one of the devices connected to the

controller or use a power source capable of delivering more current.

You will need to set the max current draw for your power supply for

this LED to work properly (as discussed later in this manual).

l If one of the ports has experienced a short circuit from a

connected device, the “Over Current” LED will blink, and

the affected port will turn off. You will need to follow the

instructions that appear later in the manual to re-enable the

port and use it again.

- The LED labeled “Under Voltage” will illuminate if the input power

to the controller is less than 11.0V DC. This could happen if your

battery power supply is nearing the end of its charge. In this case,

you would need to use a different power source or recharge the

battery. The under-voltage LED helps protect your battery from

becoming over-drained, which could reduce the battery recharge

lifetime.

l If the input voltage of the power source exceeds 13.8V, all

output ports will turn off to protect the circuitry, and the

“Under Voltage” LED will blink. In this case, you would need

to replace the power source with one that supplies less than

13.8V and manually re-enable all the output ports according

to the instructions that appear later in this manual.

If you are under dark skies and find the LEDs too bright, you can

adjust their brightness. We’ll explain how later in the manual.

ADDITIONAL CIRCUIT PROTECTION

In addition to the status LEDs’ warnings, the Smart DewHeater

Controller 2x features other circuit protection measures to keep your

equipment safe.

If the total power draw of the controller exceeds 120W (10A max

current), the controller will automatically shut off. Reduce the load on

the controller and manually re-enable the ports using the instructions

that appear later in this manual.

If you accidentally connect the input power source with the improper

polarity, the controller will not power on to prevent circuit damage.

3. Mounting the Controller to Your Setup

Decide how you want to attach the controller to your telescope setup.

There are a few options:

- Use the integrated dovetail clamp to connect the controller to a

Fig 6

Tripod strap slot

Fig 5

Clamping knobs

Product specificaties

Merk:	Celestron
Categorie:	Niet gecategoriseerd
Model:	Smart DewHeater and Controller 2x

Heb je hulp nodig?

Als je hulp nodig hebt met Celestron Smart DewHeater and Controller 2x stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Celestron

Celestron Smart DewHeater and Controller 2x Handleiding

30 Juli 2024

Celestron Thermistor 94037 Handleiding

30 Juli 2024

Celestron StarPointer Finderscope Handleiding

23 Juni 2024

Celestron OMNI AZ 102 Handleiding

5 Juli 2023

Celestron StarSense Explorer 10 Handleiding

2 Juli 2023

Celestron PowerTank 18763 Handleiding

17 Juni 2023

Celestron EclipSmart Handleiding

15 Juni 2023

Celestron PowerSeeker Handleiding

25 Mei 2023

Celestron CGX Equatorial 1100 HD Handleiding

23 Mei 2023

30 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector AS-5030.3 V2 Handleiding

21 December 2024

Sabrent AU-MMCW Handleiding

21 December 2024

Sabrent AU-2X35 Handleiding

21 December 2024

Sabrent CB-RS232 Handleiding

21 December 2024

Owon 500W Handleiding

21 December 2024

Owon 300W Handleiding

21 December 2024

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024

Sabrent SB-HTSS Handleiding

21 December 2024