Black Box LPJ001A-T Handleiding

Black Box Netwerkkaart/adapter LPJ001A-T

Lees hieronder de 📖 handleiding in het Nederlandse voor Black Box LPJ001A-T (2 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Exceeds the 802.3at standard.

Use with IP telephones, wireless access

points, IP print servers, IP cameras,

and Bluetooth® access points.

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) •

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 •

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 •

Web site: www.blackbox.com • E-mail: info@blackbox.com

Customer

Support

Information

LPJ001A-T

802.3at PoE Gigabit Injector, 1-Port

1. Specifications

Compliance: cUL/UL®; RoHS

Load (Maximum): 0.60 A

Regulation: Line and load: 54–57 VDC under all

conditions

Connectors: Data in: (1) RJ-45 (10/100/1000);

Data/PoE out: (1) RJ-45 (10/100/1000);

Power: (1) IEC 320 (3-pin)

Indicators: (3) LEDs: (1) ON, (1) PoE PLUS, (1) CONNECT

Power: AC input voltage range: 90–264 VAC;

AC input voltage rating: 100–240 VAC, 47–63 Hz;

Output: 33.6 W at 56 VDC

Size: 1.4"H x 2.6"W x 5.5"D (1 x 6.6 x 14 cm)

Weight: 0.4 lb. (0.2 kg)

2. Overview

The LPJ001A-T is a high-powered Gigabit power injector

that conforms to the IEEE 802.3at power standard.

As defined in 2009, this standard allows for a minimum

of 25 W of power to operate with PoE equipment over

a single Ethernet cable.

Use the LPJ001A-T with IP telephones, wireless access points, IP print

servers, IP cameras, and Bluetooth access points.

3. Setting Up Your Power Injector

NOTE: Use CAT5e or higher Ethernet cables (not included).

1. Using screws, affix the metal feet on the front and/or rear to a

flat surface such as a table or wall. See Figure 1.

NOTE: The power injector should not use the weight

of the Ethernet cables for support.

Figure 1. Location of metal feet on the power injector.

Power and Data in

data out

Front panel.

IEC-320 power connector.

Back panel.

Figure 2. Ports on the power injector.

2. Connect the 3-pin IEC320 AC input connector to a

power source. Power on the injector.

3. Using CAT5e or higher cable, connect the RJ-45 port

on the injector labeled “IN” to your network switch.

See Figures 2 and 3.

4. Connect the RJ-45 port labeled “OUT” on the injector over

Ethernet cable to the powered device. See Figures 2 and 3.

5. The LEDs will light to diagnose the connection. See Tables 1

and 2.

Insert a screw to

secure the unit

to a surface

Insert a screw

to secure the unit

to a surface

4. Description of LED Functions

Table 1. LEDs and their functions.

LED State Function Description

ON, PoE PLUS, All three LEDS light Power up Upon power-up, all three LEDs will light for two seconds, as

CONNECT LEDs part of the self-test for the internal microprocessor software.

ON LED Lights green after DC output After two seconds, the ON LED will light green, indicating that

two seconds voltage available the DC output voltage is available for powering an 802.3at

PoE compliant load.

CONNECT Lights green 802.3at load This green LED lights when a compliant load is attached

LED is attached to the output RJ-45 connector.

Blinking 802.3at load If the load does not comply with 802.3at PoE standards,

is not attached then the LEDs will blink a code indicating that the load

was not detected. See Table 2 for code descriptions.

PoE PLUS LED Lights green Class 4 PD If the load is classified as Class 4 PD, the PoE PLUS LED

load detected will light.

Off Load not classified If the load is not classifed as Class 4 PD, the PoE PLUS LED

as Class 4 PD will stay off.

Table 2. Failure detection codes.

Code Name Description

1 Incorrect resistive signature The green CONNECT and red PoE PLUS LEDs blink three times.

2 Incorrect capacitive signature The green ON LED blinks three times.

3 Incorrect V offset The green CONNECT and green ON LEDs blink three times.

4 Unstable current measurement The green ON LED blinks three times.

5 Low voltage sensed during detection (overload) The green PoE PLUS LED blinks three times.

NOTE: After the LEDs blink three times, the power injector will continue to try to detect a valid load. Until the correct load is applied, the LEDs

will continue to blink. If an open circuit is connected to the output RJ-45 connector, then the LEDs will not blink but the power injector will

continue to try to detect a valid load.

If a fault, such as an overload or short circuit, is detected, then all three LEDs will blink five times in three seconds, and then go off as the

power supply tries to re-detect a valid load. The LED will indicate what is wrong with the load with the codes listed in Table 2.

FREE, live, 24/7 Tech Support is just 20 seconds away.

724-746-5500 | blackbox.com

Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc.

Bluetooth is a registered trademark of The Bluetooth SIG, Inc.Any other trademarks

mentioned in this manual are acknowleged to be the property of the trademark owners.

Power and data

to powered

device

AC input

Data input from

network switch

Figure 3. Cable connections

to the power injector.

LPJ001A-T, version 2

Product specificaties

Merk:	Black Box
Categorie:	Netwerkkaart/adapter
Model:	LPJ001A-T
Gewicht:	200 g
LED-indicatoren:	Ja
AC-adapterfrequentie:	47/63 Hz
AC-adapter ingangsspanning:	90 - 264 V
Voldoet aan industriestandaarden:	cUL/UL
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Temperatuur bij opslag:	-20 - 65 °C
Bedrijfstemperatuur, bereik:	-4 - 122 °F
Ethernet interface type:	Gigabit Ethernet
Afmetingen (B x D x H):	66 x 140 x 10 mm
Bedrijfstemperatuur (T-T):	-20 - 50 °C
Stroom via Ethernet (PoE):	57 V