Bionaire BOH2503D Handleiding

Bionaire Verwarming BOH2503D

Lees hieronder de 📖 handleiding in het Nederlandse voor Bionaire BOH2503D (4 pagina's) in de categorie Verwarming. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

will instantly shut off. To reset, simply place the

heater in an upright position and press the mode

button to reactivate the unit.

TRANSPORTING THE UNIT

Locate the pull down handle (C) above the control

panel. Pull down to release and then grasp the

handle. Pull the unit using the handle ensuring that

all castors are in contact with the ﬂoor.

NOTE: Do not use handle to lift the product .

STORAGE TIPS

If the heater is not required for long periods,

for example during the summer, it should be

stored at room temperature; in a dry place and

preferably covered to prevent the accumulation

of dust and dirt.

FITTING A REPLACEMENT PLUG FOR

U.K. AND IRELAND ONLY.

If the plug is not suitable for the socket outlets in

your home, it can be removed and replaced by

a plug of the correct type. For correct type and

correct installation please refer to “Installation of

a plug” below.

INSTALLATION OF A

PLUG – Applicable to

U.K. and Ireland.

NOTE: If you are in any

doubt about wiring and

the installation of the plug.

Please contact a qualiﬁed

electrician.

NOTE: If a 13A 3-pin

plug is ﬁtted, it must be an ASTA approved

plug, conforming to the BS1363 standard.

Replacement 13 amp fuse must also be BSI or

ASTA approved.

The wires in this mains lead are coloured as such:

GREEN & YELLOW - Earth

BROWN - Live

BLUE - Neutral

Please note that the colour of these mains wires

may not correspond with the colour markings

that identify the terminals in your plug.

Please proceed as follows:

• The wire which is coloured GREEN & YELLOW

must be connected to the terminal which is

marked with the letter E ( ) or is coloured

GREEN, or GREEN & YELLOW.

• The BROWN coloured wire must be connected

to the pin terminal, which is marked with the

letter L (Live) or is coloured RED.

• The BLUE coloured wire must be connected

to the pin terminal which is marked with the

letter N (Neutral) or is coloured BLACK.

• DO NOT CONNECT either of these wires

to the earth terminal in the plug. The earth

terminal is marked with the letter E ( ) or is

coloured GREEN, or GREEN & YELLOW.

GUARANTEE

Please keep your receipt as this will be required for

any claims under this guarantee.

This appliance is guaranteed for 5 years after your

purchase as described in this document.

During this guaranteed period, if in the unlikely event

the appliance no longer functions due to a design or

manufacturing fault, please take it back to the place

of purchase, with your till receipt and a copy of this

guarantee.

The rights and beneﬁts under this guarantee are

additional to your statutory rights, which are not

affected by this guarantee. Only Holmes Products

(Europe) Ltd. (“Holmes”) has the right to change

these terms.

Holmes undertakes within the guarantee period

to repair or replace the appliance, or any part of

appliance found to be not working properly free of

charge provided that:

• you promptly notify the place of purchase or

Holmes of the problem; and

• the appliance has not been altered in any way

or subjected to damage, misuse, abuse, repair

or alteration by a person other than a person

authorised by Holmes.

Faults that occur through, improper use, damage,

abuse, use with incorrect voltage, acts of nature,

events beyond the control of Holmes, repair

or alteration by a person other than a person

authorised by Holmes or failure to follow instructions

for use are not covered by this guarantee.

Additionally, normal wear and tear, including, but not

limited to, minor discoloration and scratches are not

covered by this guarantee.

The rights under this guarantee shall only apply

to the original purchaser and shall not extend to

commercial or communal use.

If your appliance includes a country-speciﬁc

guarantee or warranty insert please refer to the

terms and conditions of such guarantee or warranty

in place of this guarantee or contact your local

authorized dealer for more information.

This marking indicates that this product should

not be disposed with other household wastes and

should be disposed separately throughout the EU.

To prevent possible harm to the environment or

human health from uncontrolled

waste disposal due to the presence

of hazardous substances within

the product, recycle it responsibly

to promote the sustainable reuse

of materials and resources. To

return your used device, please use

the return and collection systems

available to you or contact the retailer

where the product was purchased. They can take

this product for environmentally safe recycling.

Holmes Products (Europe) Limited

1 Francis Grove

London

SW19 4DT

Holmes Products (Europe) Ltd.

1 Francis Grove

London SW19 4DT

England

Fax: +44 (0)20 8947 8272

Email: enquiriesEurope@jardencs.com

UK - Filter Sales Order Line - 0870 759 9000

Website address: www.bionaire.com

UK - Free phone Customer Service Helpline – 0800 052 3615

Distributed by Holmes Products (Europe) Ltd., 1 Francis Grove, London SW19 4DT, United Kingdom. Printed in PRC

Distribué par Holmes Products (Europe) Ltd., 1 Francis Grove, London SW19 4DT, United Kingdom. Imprimé en RPC

P/N: 138197

INSTRUCTION MANUAL

OIL FILLED

RADIATOR

MODEL# BOH2503D

SPR-051010

pure indoor living

PLEASE READ AND SAVE THESE

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including the

following:

1. Before connecting the heater, check that the

voltage indicated on the rating plate corresponds

to the main voltage in your home/ofﬁce.

WARNING: In order to avoid overheating, do

not cover the heater ( ) Reference to product.

3. DO NOT position the heater directly under a

power socket.

4. DO NOT use this heater in the immediate

surroundings of a bath, a shower or a

swimming pool.

5. If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its service

agent or similarly qualiﬁed person in order to

avoid hazard. The heater contains no user

serviceable parts. Should the product suffer

damage or breakdown, it must be returned to

the manufacturer or their service agent.

6. Under the environment with electrical fast

transient, the product may malfunction.

7. DO NOT use this heater with a programmer,

timer or any other device that switches the

heater on automatically, since a fire risk

exist s if the heater is covered or positioned

incorrectly.

8. Only touch the heater with dry hands.

9. DO NOT use this heater outdoors.

10. DO NOT position where it can be touched by

children, especially the very young.

11. Allow a safe area around the heater away from

furniture or other objects; at least 50 cm from

the top and sides and 200 cm at the front. The

heater is to be placed at least 3m from water

source.

12. DO NOT use this heater when it is lying on its

side.

13. DO NOT use the heater in rooms with

explosive gas (e.g. petrol) or while using,

oxygen, inﬂammable glue or solvent (e.g. when

gluing or varnishing parquet ﬂoors, PVC etc.)

14. DO NOT insert any objects into the heater.

15. Keep the mains cord at a safe distance from

the main body of the heater.

16. If overheating should occur, the built-in

overheating safety device will switch off the

heater.

17. DO NOT place the cord under a rug.

18. The heater cannot be used adjacent to

curtains or combustible material. Curtains or

combustible material may be burned if the

heater was installed incorrectly.

19.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

20. This heater is ﬁlled with a precise quantity

of special oil. Repairs requiring opening of

the oil container are only to be made by the

manufacturer or his service agent who should

be contacted if there is an oil leak;

21. When scrapping the heater, follow the

regulations concerning the disposal of oil.

DESCRIPTIONS (See Fig. 1, 2 & 3)

A. Heated fins

B. Vents

C. Pull down handle

D. Power switch

E. Cord Storage

F. Power cord

G. Front castor assembly

H. Digital display

I. Power light

J. Mode light

K. Timer light

L. Mode button

M. Thermostat/timer button

N. Adjuster buttons

O. °F - °C button

P. Front wing nut

Q. Castor

R. Rear castor assembly

S. Rear wing nut

T. U-bolt

Technical Speciﬁcations

BOH2503D: Wattage: 2500W

ASSEMBLY INSTRUCTIONS (See Fig. 3)

Please make sure the heater has not been

plugged into any electricity outlet. Carefully remove

heater from box. Some accessories are packed

internally. Please make sure you have all of the

following accessories prior to throwing away

packaging.

2 Castor assemblies with four castors

(R, G, & Q),

and 2 U Bolts with wing nuts (T, P, S).

Note: This unit is for FLOOR USE ONLY.

1. Turn the heater upside down and you will see

2 U-bolts (T) with wing nuts over the ﬁrst and

last joint of the heater.

2. Unscrew the wing nuts (S & P) from the

U-bolts (T).

3. Start with the front of the unit and place one

hole of the front castor assembly (G) to the L

shape of the U-bolt (T) and the other hole of

the castor assembly into the other end of the

U-bolt, then screw on the wing nut (P).

4. Repeat step 3 for the rear castor assembly,

using wing nut (N) instead of wing nut (K) and

rear castor assemblies (M).

5. Use your hand to press the four casters (L)

onto the four axis of the two foot plates until

you hear them click into place. Use your hand

U.K. and IRELAND

to turn the castors and if the move smoothly

they have been installed properly.

6. After installation of the front and rear castor

assemblies and the castors turn the heater

the right way up: the heater is now ready

for use.

NOTE: Make sure when assembling that the

castor assemblies with wheels are pointing

outwards for maximum stability.

OPERATING INSTRUCTIONS

(See Fig. 1&2)

1. Ensure the power switch (D) is set to the OFF

(O) position.

2. Plug in heater.

3. Flip the power switch to the ON (-) position. The

power light (I) will illuminate red until the unit is

unplugged.

4. Press the mode button (L) once to activate the

unit. The mode light (J) will glow green to indicate

the heater is running. The unit will automatically

start on Setting 3 (High Heat).

5. Press the mode button until the desired heat

setting is shown on the digital display (H).

BOH2503D: 3=2500W, 2=1300W, 1=1200W,

=Energy Saving Mode

After using the heater, press the mode button

until the unit is deactivated and the mode light

turns off, then turn the power switch to the OFF

position. Unplug the heater from the socket.

SETTING THE THERMOSTAT

1. Set the desired heat setting by pressing the mode

button.

2. Press the thermostat/timer button (M) once to

activate thermostat setting. The room temperature

and a thermostat icon ﬂash on the display.

3. Press the + or - adjuster buttons (N) to select the

desired temperature. (Range 12° C - 30° C)

4. The thermostat symbol will stop ﬂashing. The

thermostat control will now automatically maintain

the preset temperature level by turning the heater

on and off.

5. To deactivate the thermostat setting, press

the thermostat/timer button continuously until

the thermostat symbol does not appear on the

display.

NOTE: The Power light will remain lit during

operation.

NOTE: It is normal for the heater to cycle ON

and OFF as it maintains the preset temperature.

FROST GUARD INSTRUCTION

When the heater is in frost guard mode, the

temperature will be maintained at 5° C; thus the

heater will be in the off status unless the room

temperature is lower than 5° C. If the room

temperature is lower than 5° C, the heater will

automatically start working and will keep turning

on & off all the time, maintaining its ambient

temperature of 5° C. To activate, press the

mode button to turn the unit on, then press the

thermostat/timer button twice. The ( ) icon will

display to indicate that frost guard is activated.

USING THE TIMER

Programmable timer

The user can programme the heater to turn

OFF after a selected period or to come ON at a

preset time.

Setting the OFF timer

1. Select the mode and temperature you want

the heater to run.

2. Press the thermostat/timer button 3 times.

The OFF timer icon ﬂashes.

3. Using either the (+) or (-) adjuster buttons,

programme the heater to turn off up to 24

hours later, in increments of 1 hour.

Example - 9 hours

4. After setting the time, the digital display

will stop ﬂashing to show the timer is

activated. The timer will count down until the

predetermined length of time has passed, and

the heater will then automatically switch off.

Example - Switch OFF - The time is 1 pm. The heater

is running and you require the heater to switch off at

10 pm; therefore, set the time to 9 hours.

Setting the ON timer

1. If the heater is on, press the thermostat/timer

control button 4 times. The ON timer icon ﬂashes.

2. Using either the (+) or (-) adjuster buttons,

programme the heater to switch on up to 24

hours later, in increments of 1 hour.

Example - 4 hours

3. After setting the ON timer, the digital

display will stop ﬂashing to show the timer is

activated. The timer will count down until the

predetermined period has passed, and then the

heater will automatically switch on.

NOTE: When the ON timer is set, the unit will

remember the setting the unit was previously on

and activate to this setting after the predetermined

period. The heat setting may be changed after

setting the timer by pressing the mode button.

ENERGY SAVING MODE

To activate, press the mode button until

appears on the display. The heater will operate

on a cycle – 10 minutes on High (2500W) and

30 minutes on Medium (1300W). When the

temperature is at or above 85ºF (30ºC), the

heater will ignore the 10 minute High setting and

operate on Medium for 30 minutes immediately.

The cycle repeats while in this mode.

DISPLAY PREFERENCES

The default setting on the digital display is

degrees Celsius (°C). To switch to degrees

Fahrenheit (°F), press the °F-°C button.

NOTE: Unit must be unplugged for it to be fully off.

TIP OVER PROTECTION

When the unit is accidentally knocked over, or

tilts on one side at more than a 45° angle; it

BOH2503D

Fig. 1 Fig. 2

F C

Fig. 3

Product specificaties

Merk:	Bionaire
Categorie:	Verwarming
Model:	BOH2503D
Kleur van het product:	Wit
Timer:	Ja
Vermogen:	2500 W
Snoeropslag:	Ja
Instelbare thermostaat:	Ja
Aantal buizen:	11