Atlantic LST Handleiding
Atlantic
Verwarming
LST
Lees hieronder de 📖 handleiding in het Nederlandse voor Atlantic LST (10 pagina's) in de categorie Verwarming. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/10

Experts in Electric Heating and Hot Water
atlanticheat.co.uk | TOTAL ELECTRIC SOLUTIONS.
LST
LOW SURFACE TEMPERATURE
PANEL HEATER

Overview
Please read this guide carefully and retain
for future use and maintenance.
This appliance has been designed and
manufactured to the highest international
standards, however, care must be taken
for optimal results and safety. This
appliance also meets the requirements of
EU Directive 2004/106/EC for EMC and
2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for their
safety. Children should be supervised to
ensure that they do not play with the
appliance.
Warning
• Do NOT site the appliance in a corner.
• Do NOT handle the appliance with wet
hands.
• Do NOT use the appliance in workshops
or rooms where excessive dust is
generated or present.
• Ensure that nothing is pushed into any
aperture of this appliance.
• Do NOT touch outlet grille when the
appliance is in use.
• Do NOT cover or restrict any aperture of
the appliance when in use.
• Do NOT use the appliance if damaged.
• Do NOT leave the appliance
unattended where young children are
present.
• If used in a bathroom, the heater is to
be installed so that the switches and
other controls cannot be touched by a
person in the bath or shower.
• Operating temperature range -10 to +40
ºc
• The heater MUST be fully secured in the
vertical position before being switched
on.
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated
cut-out (TOC). This is a safety device, which
switches the heater off if, for any reason, the
appliance overheats. The TOC can only be re-set
after the appliance has cooled down. In order to
re-set the TOC, proceed as follows:
• Switch off appliance and leave for
approximately 10 minutes.
• Switch appliance back on and TOC will re-
set.
• Ensure that the appliance is functioning
correctly. If the TOC operates again, the
appliance should be checked by a
competent electrician.
The heater carries a ‘Do Not Cover’ label to warn
the user that if the appliance is covered, there is a
risk of overheating.
Cleaning
Always disconnect the heater from the mains
before cleaning. The heater should not require any
maintenance, but it is strongly advised that it is kept
clean. An occasional wipe over with a soft cloth is
all that should be necessary.
• Do NOT use metal or furniture polish on any part
of the heater.
• Do NOT touch the heater with wet hands or in
any way bring water into contact with it.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
If Your Heater Does Not Work
• Check that power is available to the heater.
• Check that the thermal cut-out has not
operated. Follow the reset instructions given
under the section headed ‘Thermally Operated
Cut-out’.
• Check that the fuse in the spur unit has not
blown. This can be done by replacing the fuse
with another suitable fuse.
Should none of the above remedies work, then
telephone the helpline number shown in these
instructions (UK ONLY). Do not attempt to repair the
heater.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with
NICEIC (National Inspection Council for Electrical
Installation Contracting) in accordance with the 17
edition of the IEE Wiring Regulations, (BS.7671), and
any relevant Local Authority Bye-Laws. This heater is
fitted with a 3-core mains supply cable and must
be permanently connected to the electricity
supply via a double pole switch having 3mm gap
on each pole. There are no exceptions. A switched
Fused Connection unit to BS.1363. Part 4 is a
recommended mains supply connection accessory
to ensure compliance with safety requirements
applicable to fixed-wiring installation.
Note: When switched on for the first time the
appliance may emit a slight smell. This is purely the
evaporation of a fluid used in the manufacturing
process.
WARNING: This appliance must be earthed.

General Safety
Our Low Surface Temperature heaters
have been designed and built to the NHS
requirement for safe surface
temperatures which is that no surface
which can be touched by the user will be
more than 43 ºC (at a room temperature
of 21 ºC) This means that our Low Surface
Temperature heaters out-perform the
European Standard by a significant
margin.
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety. Children should be supervised
to ensure that they do not play with the
appliance.
Safety Monitor
As part of the intelligent control (see
section 15), the heater has built-in safety
monitoring. In the unlikely event of a fault,
the safety monitoring will help prevent high
surface temperatures. The safety monitor
will identify overheating, fan failure and
certain electronic faults. When the safety
monitor identifies a fault, the heater runs in
restricted mode. However, in the event of
a serious fault the heater stops running.
The heater indicates a fault by beeping
twice. It will not beep again until the unit is
switched off and then back on, but the
LED will flash red continuously.
2. Optional PLK1 Locking Device
The PLK1 locking device can be used to mechanically
lock the controls to prevent tampering with settings. As it
is not supplied with the heater, kindly contact our Sales
team if required.
- Locking tab
- Locking screw
Locking tab Locking screw
1. Mounting
This unit is for wall mounting only. It is designed to be
very quiet in operation if mounted correctly. It must be
fitted using the wall bracket supplied and screws for a
5mm hole. The wall bracket provided has been specially
designed to minimise noise levels. Care must be taken
when handling the bracket not to bend or distort it.
When fitting more than one heater in a room we would
recommend that they are sited on the same wall to
optimise airflow and ensure quiet operation.
To wall mount, the wall bracket supplied must be used.
Remove the wall bracket from the heater, with the
chains attached, by removing the 2 securing screws from
the top of the rear panel.
Fix the wall bracket to the wall using 4 screws.
Fig 1: Present the heater to the bracket
Fig 2: Locate the heater onto the bottom lugs via the 2
slots in rear panel. Hinge the heater upwards and attach
the chain assembly, then move the heater to the upright
position. The link plates should slide under the slotted
bracket lip.
Fig 3: Tighten both retaining screws.
MOUNTING ON A PLASTERBOARD WALL
• Ensure at least one of the wall brackets is secured
to the timber frame of the studded wall by using
standard wood screws.
• Where the bracket is fitted onto plasterboard only,
ensure plasterboard fixings are used. Standard wall
plugs will not be suitable.
• Where possible mount the heater(s) on an outside
wall to inhibit transfer of sound within the building.
NB: Failure to follow the instructions and
recommendations provided could result in increased
noise levels.
The heater must not be located immediately below a
fixed socket outlet.
Product specificaties
Merk: | Atlantic |
Categorie: | Verwarming |
Model: | LST |
Heb je hulp nodig?
Als je hulp nodig hebt met Atlantic LST stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verwarming Atlantic

4 April 2025

4 Juni 2023

4 Juni 2023

4 Juni 2023

4 Juni 2023

4 Juni 2023

4 Juni 2023

4 Juni 2023

4 Juni 2023

4 Juni 2023
Handleiding Verwarming
- Verwarming Bosch
- Verwarming AEG
- Verwarming Junkers
- Verwarming Nefit
- Verwarming Quigg
- Verwarming Remeha
- Verwarming Vaillant
- Verwarming Alde
- Verwarming BeF Home
- Verwarming Bionaire
- Verwarming Blumfeldt
- Verwarming Brink
- Verwarming Danfoss
- Verwarming Dimplex
- Verwarming DIO
- Verwarming Duronic
- Verwarming Duux
- Verwarming Easy Home
- Verwarming Easymaxx
- Verwarming Eberspacher
- Verwarming Ecoforest
- Verwarming Etherma
- Verwarming Eurom
- Verwarming FlinQ
- Verwarming Gude
- Verwarming Haceka
- Verwarming Heatstrip
- Verwarming Kompernass
- Verwarming Magma
- Verwarming Mesa Living
- Verwarming Mill
- Verwarming Mio Star
- Verwarming Mocoori
- Verwarming Myson
- Verwarming Plieger
- Verwarming Powerfix
- Verwarming REMKO
- Verwarming Rowi
- Verwarming Sonnenkonig
- Verwarming Stiebel Eltron
- Verwarming Suntec
- Verwarming Supra
- Verwarming Thermor
- Verwarming Toolland
- Verwarming Trumatic
- Verwarming Vasco
- Verwarming Viessmann
- Verwarming Vintec
- Verwarming Vlectro
- Verwarming Wallas
- Verwarming Webasto
- Verwarming Weishaupt
- Verwarming Zehnder
- Verwarming Jaga
- Verwarming JML
- Verwarming Wilfa
- Verwarming Eldom
- Verwarming Campingaz
- Verwarming Day
- Verwarming Cecotec
- Verwarming Ecron
- Verwarming Climastar
- Verwarming Kemper
- Verwarming Zymbo
- Verwarming Create
- Verwarming Besoa
- Verwarming Cbn
- Verwarming Sevva
- Verwarming Rotheigner
Nieuwste handleidingen voor Verwarming

3 April 2025

16 Februari 2025

14 Februari 2025

26 Januari 2025

5 Maart 2025

16 Februari 2025

26 Januari 2025

16 Februari 2025

16 Februari 2025

16 Februari 2025