Be Quiet! Dark Rock Pro 4 Handleiding

Be Quiet! Processorkoeler Dark Rock Pro 4

Lees hieronder de 📖 handleiding in het Nederlandse voor Be Quiet! Dark Rock Pro 4 (2 pagina's) in de categorie Processorkoeler. Deze handleiding was nuttig voor 99 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

First remove the protective foil from the underside of the cooler.

Spread the thermal paste (17) on the surface of the CPU. The

amount supplied is sufﬁcient for one or two applications.

Caution: The thermal paste supplied is not suitable for human

consumption. If swallowed, drink lots of water and urgently

seek medical attention. Keep it out of the reach of children.

Avoid contact with skin and eyes.

Position the cooler mounting bridge (7) centrally on the cooler.

Next place the cooler unit over the CPU. Loosen both heatpipe

caps that are found in the middle of the top side of the cooler.

Insert the Intel/AMD mounting bridge fastening screws (12)

from above into the cooler mounting bridge and then screw

these alternately tight.

You can use the cross-tip screwdriver (16) for this.

Subsequently retighten both heatpipe caps on the top side of

the cooler.

Fasten the 120mm fan (3) using fan clips (18) onto the front

side of the cooler. Slide the 135mm fan (2) between the two

heatsinks and also fasten this with fan clips (18). Connect

both fans using the the Y cable (20). Connect this to the

CPU fan connector on the motherboard.

When dismantling the fans, push the notches of the fan

clips (18) away from the fan.

Position the cooler mounting bridge (7) centrally on the cooler

(1). Next place the cooler unit over the CPU. Loosen both

heatpipe caps that are found in the middle of the topside of the

cooler (rotate as illustrated). Insert the Intel/AMD mounting

bridge fastening screws (12) from above into the cooler

mounting bridge (7) and then screw these alternately tight. You

can use the cross-tip screwdriver (16) for this.

Subsequently retighten both heatpipe caps on the top side of

the cooler.

Fasten the 120mm fan (3) using fan clips (18) onto the front

side of the cooler. Slide the 135mm fan (2) between the two

heatsinks and also fasten this with fan clips (18). Connect

both fans using the the Y cable (20). Connect this to the

CPU fan connector on the motherboard.

When dismantling the fans, push the notches of the fan

clips (18) away from the fan.

Introduction: Thank you for deciding to purchase a be quiet!

product. The following instructions will guide you through the

installation process. If you do encounter installation problems,

please don't hesitate to contact our customer services by

mailing service@bequiet.com. Please note that be quiet!

cannot accept liability for damage caused by compatibility

problems.

Warranty:

• 3 years manufacturer guarantee for consumers (original

purchase from authorized be quiet! dealers only)

• Guarantee work can only be processed with an included

copy of the purchase receipt from an authorized be quiet!

dealer

• Manipulation and structural changes of any kind as well

as damages through external mechanical forces lead to a

complete voiding of the guarantee

• Our General Warranty Conditions apply, which can be

viewed on bequiet.com

Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde

Germany

For further information contact us via e-mail:

service@bequiet.com

SCOPE OF DELIVERY

General

We recommend preparatory mounting of the

cooler outside the PC case for subsequent

installation.

The following parts are needed for this:

1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

fan (3), 2x Intel mounting brackets (5), 1x cooler mounting

bridge (7), 4x Intel spacer nuts (8), 4x mounting bracket

fastening screws (11), Intel/AMD mounting bridge fastening

screws (12), 1x cross-tip screwdriver (16), 1x thermal paste

(17), 4x fan clips (18), 1x Y cable (20)

Assembly of the cooler mounting frame

First screw the Intel spacer nuts (8) onto the threads of the

socket frame. Place the Intel mounting brackets (5) over the

Intel spacer nuts and screw these tight with the mounting

bracket fastening screws (11). You can use the cross-tip

screwdriver (16) for this.

First remove the protective foil from the underside of the cooler.

Spread the thermal paste (17) on the surface of the CPU. The

amount supplied is sufﬁcient for one or two applications.

Caution: The thermal paste supplied is not suitable for

human consumption. If swallowed, drink lots of water and

urgently seek medical attention. Keep it out of the reach of

children. Avoid contact with skin and eyes.

Installation video

1366, 2011(-3) square ILM, 2066

1150, 1151, 1155, 1156

General

We recommend preparatory mounting of the

cooler outside the PC case for subsequent

installation.

The following parts are needed for this:

1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

fan (3), 1x Intel backplate (4), 2x Intel mounting brackets (5),

1x cooler mounting bridge (7), 4x Intel 115X/1366 nuts (9), 4x

mounting bracket fastening screws (11), 2x Intel/AMD mounting

bridge fastening screws (12), 4x Intel backplate screws (13), 4x

O-rings (15), 1x cross-tip screwdriver (16), 1x thermal paste (17),

4x fan clips (18), 1x Y cable (20)

Mounting the backplate

Position the Intel backplate screws (13) in the notches situated

on the rear side of the Intel backplate (4). Pay attention in so

doing to align with the holes specially drilled for each socket.

For ﬁxing the backplate screws onto the Intel backplate use

the O-rings (15). Once assembly of the Intel backplate for the

respective Intel socket is complete, position it under the

motherboard. In so doing make sure that the Intel backplate

screws (13) are precisely positioned inside the motherboard

holes.

Assembly of the cooler mounting frame

Screw the Intel 115X/1366 nuts (9) onto the previously

positioned Intel backplate (4). Then position the Intel mounting

brackets (5) over the Intel 115X/1366 nuts and afﬁx these with

the mounting bracket fastening screws (11). You can use the

cross-tip screwdriver for this (16).

1366, 2011(-3) square ILM, 2066

1150, 1151, 1155, 1156

Intel LGA 2011(-3) square ILM / LGA 2066 Intel LGA 1150 / 1151 / 1155 / 1156 / 1366

We recommend removal of the cooler prior to transportation.

January 2018

Part name Quantity

be quiet! Dark Rock Pro 4 cooler 1

135mm fan 1

120mm fan 1

Intel backplate 1

Intel mounting brackets 2

Short AMD mounting brackets 2

Cooler mounting bridge 1

Intel spacer nuts 4

Intel 115X/1366 nuts 4

Part name Quantity

AMD spacer nuts 4

Mounting bracket fastening

screws 4

Intel/AMD mounting bridge

fastening screws 2

Intel backplate screws 4

AMD backplate screws 4

O-rings 4

Cross-tip screwdriver 1

Thermal paste 1

Fan clips 2

AM3 washers 4

Y cable 1

Installation video

1366

1150, 1151,

1155, 1156

Position the cooler mounting bridge (7) centrally on the cooler.

Next place the cooler unit onto the CPU. Loosen both heatpipe

caps that are found in the middle of the topside of the cooler

(rotate as illustrated).

Insert the Intel/AMD mounting bridge fastening screws (12)

from above into the cooler mounting bridge and then screw

these alternately tight. You can use the cross-tip screwdriver

(16) for this. Subsequently retighten both heatpipe caps on the

topside of the cooler.

Fasten the 120mm fan (3) using fan clips (18) onto the front

side of the cooler. Slide the 135mm fan (2) between the two

heatsinks and also fasten this with fan clips (18). Connect

both fans using the Y cable (20). Connect this to the CPU

fan connector on the motherboard.

When dismantling the fans, push the notches of the fan clips

(18) away from the fan.

General

We recommend preparatory mounting of the

cooler outside the PC case for subsequent

installation.

The following parts are needed for this:

1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

fan (3), 2x short AMD mounting brackets (6), 1x cooler mounting

bridge (7), 4x AMD spacer nuts (10), 2x Intel/AMD mounting

bridge fastening screws (12), 4x AMD backplate screws (14), 1x

cross-tip screwdriver (16), 1x thermal paste (17), 4x fan clips (18),

4x AM3 washers (19), Y cable (20)

Assembly of the cooler mounting frame

To permit mounting of the cooler please remove both the

plastic retainers of the AMD retention module. The factory-

ﬁtted backplate afﬁxed to the rear side of the motherboard will

be needed for subsequent installation of the cooler.

Note: To mount the Dark Rock Pro 4 on an AM3 motherboard,

please use the AM3 washers (19), placing these over the

backplate bolts protruding through the front side of the

motherboard.

Place the 4x AMD spacer nuts (10) onto the backplate bolts

protruding through the front side and afﬁx both short AMD

mounting brackets (6) with the AMD backplate screws (14).

Mounting the CPU cooler:

First remove the protective foil from the underside of the

cooler. Spread the thermal paste (17) on the surface of the

CPU. The amount supplied is sufﬁcient for one or two

applications.

Caution: The thermal paste supplied is not suitable for human

consumption. If swallowed, drink lots of water and urgently

seek medical attention. Keep it out of the reach of children.

Avoid contact with skin and eyes.

AMD AM2(+) / AM3(+) / AM4 / FM1 / FM2(+)

AM4

AM2(+) / AM3(+) / FM1 / FM2(+)

Notes

bequiet.com

Installation video

Limited Warranty

Per the terms and conditions of this limited warranty as given below,

be quiet! warrants its new products to be free of defects resulting

from faulty materials and faulty manufacturing for the length of the

warranty period.

I. APPLICABILITY

This non-transferable warranty is applicable to newly purchased,

previously unopened be quiet! products and is enforceable by only

the original consumer purchaser. Proof of purchase is required for

warranty service, so should be retained. be quiet! does not provide

warranty registration services.

II. WARRANTY PERIOD

For eligible products, parts and labor are warranted for the appli-

cable warranty period from the date of purchase. The applicable

warranty period varies by product model, and is identied in your

user documentation, on the product package, or as listed below.

Should any of these warranty periods dier, the longest specied

warranty period will apply. Replaced products will be warranted

for the remainder of the original warranty period or thirty days,

whichever is longer.

III. EXCLUSIONS

The following are not covered by the warranty:

1. Normal wear and tear.

2. Any product which has been modied without permission from

be quiet!, or on which the serial number or warranty sticker has been

defaced, modied, or removed.

3. Damage, deterioration or malfunction resulting from:

Accident, abuse, misuse or improper use, neglect, connection to

an improper voltage source, unauthorized product modication, or

failure to follow instructions included with the product.

Fire, water, lightning, or other acts of nature.

Repair or attempted repair by anyone not authorized by be quiet!.

Shipping or transport damage (claims must be made with the carrier).

Any other cause which does not relate to a defect in materials or

manufacturing workmanship.

4. Cartons, cases, batteries, cabinets, tapes, accessories or other

consumables used with this product.

5. be quiet!, Inc. does not warrant that this product will meet your

requirements. It is your responsibility to determine the suitability of

this product for your purpose.

6. Removal or installation charges.

7. Shipping charges.

8. Any incidental charges.

IV. EXCLUSION OF DAMAGES

be quiet!‘s sole obligation and liability under this warranty is limited

to the repair or replacement of a defective product at its option.

be quiet! shall not, in any event, be liable for any special, incidental,

indirect, or consequential damages whatsoever, including but not

limited to loss of prots, revenue, or data (whether direct or indirect),

damages resulting from interruption of service and loss of business,

or for liability in tort relating to this product or resulting from its use

or possession, even if be quiet! has been advised previously of the

possibility of such damages.

V. LIMITATIONS OF IMPLIED WARRANTIES

There are no other warranties, expressed or implied, including but not

limited to those of merchantability or tness for a particular purpose.

The duration of implied warranties is limited to the warranty length

specied in Paragraph II.50

VI. LOCAL LAW AND YOUR WARRANTY

This warranty gives you specic legal rights. You may also have other

rights granted under local law. These rights may vary.

VII. NO OTHER WARRANTY

No be quiet! employee, dealer, or other agent is authorized to make

any modication, extension, or addition to this warranty.

VIII. TO OBTAIN TECHNICAL SUPPORT OR WARRANTY SERVICE

Please see your product owner’s manual or visit the Online Support

section at www.bequiet.com for details and contact information. You

will need to provide proof of purchase for warranty service.

bequiet.com

Product specificaties

Merk:	Be Quiet!
Categorie:	Processorkoeler
Model:	Dark Rock Pro 4
Kleur van het product:	Zwart
Gewicht:	1130 g
Breedte:	136 mm
Diepte:	162.8 mm
Hoogte:	123.7 mm
Snoerlengte:	0.22 m
Gewicht verpakking:	1390 g
Breedte verpakking:	205 mm
Diepte verpakking:	181 mm
Hoogte verpakking:	212 mm
Soort:	Koeler
Geluidsniveau (lage snelheid):	12.8 dB
Geluidsniveau (hoge snelheid:	24.3 dB
Netvoeding:	1.92 W
Materiaal:	Koper
Duurzaamheidscertificaten:	RoHS
Aantal ventilatoren:	2 ventilator(en)
Thermal Design Power (TDP):	250 W
Rotatiesnelheid ( max):	1500 RPM
Inclusief schroeven:	Ja
Geschikte locatie:	Processor
Code geharmoniseerd systeem (HS):	84733080
Ventilator diameter:	120/135 mm
Spanningclassificatie:	12 V
Nominale netspanning:	0.16 A
Supported processor sockets:	LGA 1150 (Socket H3), LGA 1151 (Socket H4), LGA 1155 (Socket H2), LGA 1200 (Socket H5), LGA 1700, LGA 2011 (Socket R), LGA 2011-v3 (Socket R), LGA 2066, Socket AM4, Socket AM5
Pulsbreedtemodulatie-ondersteuning:	Ja
Type lager:	Vloeistof dynamisch lager (FDB)
Aantal vinnen:	90
Materiaal vinnen:	Aluminium
Aantal warmte pijpen:	7
Maten ventilator (b x d x h):	135 x 135 x 22 mm
Warmte pijpen diameter:	6 mm
Fan connector:	4-pin
Extra ventilator ondersteund:	Ja