Audio-Technica AT-DMM828 Handleiding

Audio-Technica Mengpaneel AT-DMM828

Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica AT-DMM828 (23 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/23
AT-DMM828
Digital Matrix Mixer
Installation and Operation Ver.2
AT-DMM828
Digital Matrix Mixer
Installation and Operation
Warning:
To prevent fire or shock hazard, do not expose this apparatus to rain or
moisture.
Caution:
To avoid electric shock, do not open the cabinet.
Refer servicing to qualified personnel only.
To prevent fire, do not place any naked flame sources (such as lighted
candles) on this apparatus.
To prevent fire, do not cover the ventilation of this apparatus with
newspapers, table-clothes, curtains, etc.
Do not expose this apparatus to drips or splashes.
Do not place any objects filled with liquids, such as vases, on this apparatus.
Do not install this apparatus in a confined space such as a bookcase or
similar unit.
To install this apparatus only in the place where ventilation is good.
This apparatus should be located close enough to the AC outlet so that you
can easily grasp the power cord plug at any time.
In case of emergency, disconnect the power cord plug of this apparatus
quickly.
This apparatus with Class
Ⅰconstruction shall be connected to the AC outlet
with a protective grounding connection.
This apparatus is not disconnected from the mains as long as it is connected
to the AC outlet, even if the unit itself has been turned off.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type
plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Caution for FCC
You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.
Warning for FCC
This device complies with Part 15 of the　FCC Rules. Operation is subject
to the　following two conditions: (1)This device may not cause harmful
interference, and(2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
IC statement
CAN ICES-3 (B)/NMB-3(B)
About Power Cord
This model does not include AC power cord.
Therefore, you have to purchase it at your local store. You can confirm it at
“Power Cord List”.
Power Cord List
Power supply cord for 120 Vac power supply in U.S.A, Canada :
Approved by UL, CSA
Detachable, rated minimum 125 V, minimum 10 A, marked VW-1. Includes 3 x
18 AWG, Type SVT flexible cord. Minimum length 1.5 m.
One end terminates in a parallel blade, molded-on attachment plug rated 125
V, 10 A with a polarized NEMA 5-15P blade configuration.
Other end terminates in an appliance coupler.
2
3
Introduction
Please Note!
This manual assumes use of microphone-level inputs and line-level output
for most typical SmartMixer applications. However, all inputs may be
individually switched via the included AT-DMM828 Control Software to
achieve any combination of mic-level and line-level inputs.
Signal flow can be changed via the included AT-DMM828 Control Software.
Refer to Software Manual for more information.
About the AT-DMM828
AT-DMM828 is a microprocessor-controlled, programmable, automatic-
switching eight-channel matrix mixer. It can be used with low-impedance
either dynamic or condenser microphones (including wireless microphone
systems), as well as line-level sources.
AT-DMM828 is designed to improve audio quality in broadcast, sound-
reinforcement and recording applications. One way it achieves this is
by keeping the number of open microphones to minimum, thus reducing
background noise, feedback and other distractions, while providing instant,
completely transparent switching between channels.
Each of the eight balanced inputs provides switchable 48Volt phantom
power; attenuation is also selectable on each input to allow use with line-
level signals. The mixer's outputs are balanced and non-inverting. All audio
connections terminate in block screw connectors.
Up to 16 units of AT-DMM828 (a total of 128 channels inputs) can be daisy-
chained via CAT6 cable, which carries control bus, audio, and configuration
data between mixers.
Multiple mixers linked in this way will operate as if they are a single mixer.
Therefore, microphones activated on any mixer will cause the appropriate
switching functions to occur. The link connectors are not compatible with
LAN.
Each AT-DMM828 includes two separate external control system interfaces:
Individual channel contact closures (via DB25 connector) and PC control (via
RS232 connector or USB). The RS232 connector can also be used to connect
an external control system (e.g. Crestron
® or AMX®) using “open disclosure
communication protocol” to control the mixer.
AT-DMM828 Features
• Eight balanced inputs allow to be used with either mic-level or line-level
signal.
Each input provides:
°　 Smart Mixer V1 (Gating mode)
°　 Smart Mixer V2 (Gain Sharing mode)
*Supported by AT-DMM828 Ver.2 or later
°　 48V phantom power (individually selectable)
°　 Individual gain and sound volume controls
°　 Gate attenuation adjustable (0 dB to full mute in steps of 1 dB)
°　 Gate hold time adjustable (0.1 sec to 6.0 sec in steps of 0.1 sec)
°　 Mic on threshold level adjustable (Auto/Manual)
• DSP algorithm
°　 Signal level meter (Peak/RMS)
°　 Signal generator (Sine wave/Pink noise/White noise)
*input channel
only
°　 Parametric EQ (3 band/4 band)
°　 Filter (Low pass/High pass/Low shelving/High shelving/Notch/All
pass)
°　 Limiter
°　 Delay *output channel only
°　 8×8 full matrix-mixing (can be extended to 128×8 matrix-mixing)
• Selectable NOMA (Number of Open Microphones Attenuated)
°　 Automatic gain adjustment as each microphone is activated
• Selectable manual mode overrides automatic functions
• Linking capability for up to 16 units (up to 128 inputs)
• Selectable external connector’s pin assignment
°　 Gate status output (using for the Camera moving)*
°　 Gate On/Off
/Toggle
(using for input gate control by tactile switch)*
°　
Mute On/Off/Toggle (
using for channel level control by tactile switch
)*
°　
Volume Up/Down (
using for channel level control by tactile switch
)*
°　 VCA function (using for channel level control by external
potentiometer)
*Positive/Negative selectable
• Compatible with Crestron
® or AMX® systems
• All settings can be adjusted or modified through AT-DMM828 Control
Software
• Mounts in a single U 19” rack space (EIA Standard)

Product specificaties

Merk: Audio-Technica
Categorie: Mengpaneel
Model: AT-DMM828

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica AT-DMM828 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Mengpaneel Audio-Technica

Audio-Technica

Audio-Technica AT-DMM828 Handleiding

15 Mei 2023
Audio-Technica

Audio-Technica AT-MX341b Handleiding

5 Maart 2023
Audio-Technica

Audio-Technica SmartMixer AT-MX351a Handleiding

4 December 2022

Handleiding Mengpaneel

Nieuwste handleidingen voor Mengpaneel

NutriBullet

NutriBullet Ultra 1200 Handleiding

16 November 2024
Mackie

Mackie ProFX12 Handleiding

15 November 2024
Solid State Logic

Solid State Logic SSL UF1 Handleiding

15 November 2024
Yamaha

Yamaha IM8-32 Handleiding

14 November 2024
Yamaha

Yamaha IM8-40 Handleiding

14 November 2024
Yamaha

Yamaha DCU5D Handleiding

14 November 2024
Yamaha

Yamaha SP02R96 Handleiding

14 November 2024
Yamaha

Yamaha MG166C-USB Handleiding

13 November 2024
RCF

RCF L-PAD 12C Handleiding

5 November 2024
RCF

RCF L-PAD 10C Handleiding

5 November 2024