Audibax MG08 USB Handleiding

Audibax Mengpaneel MG08 USB

Lees hieronder de 📖 handleiding in het Nederlandse voor Audibax MG08 USB (13 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/13
MG MG MG04 USB / 06 USB / 08 USB
Please read the manual before using the product
USER´S
MANUAL
11
MG04 USB
MG06 USB
MG08 USB
Notes:
USER´S
MANUAL
MG MG MG04 USB / 06 USB / 08 USB
1 10
*Built-in 16 bit DSP processor
*Built-in Bluetooth connect with mobile phone or other Bluetooth player
*Built-in MP3 player support a variety of formats music
*Connect the computer to record and play music
1.4/6/8 channels mixer 2.Mic + stereo line inputs
3.Ultra-musical 3-band EQ on all channels 4.Peak LED on all Channels
5.High accurate level indicator 6.Phantom power switch (+48V)
7.Sealed rotary controls to resist dust and grime 8.Rugged steel chassis
9.New Multi-Voltage power supply for worldwide use
CHANNEL INPUT
1.[MIC] Input, use this socket to connect the microphone of BALANCED XLR PLUG.
2. [LINE] Input, connect the microphone, musical instrument or audio device (CD
player and so on) to the device. The socket is supporting UNBALANCED 1/4"
PLUG.
3. [INSERT] Input, can be inserted into a mono channel of compressor or equalizer.
4. [GAIN] Controller, determines the basic volume of each channel, adjust them
for the maximum volume performance, when the volume gets too loud, the
[PEAK]LED (9) indicator light will keep flashing.
5. [HIGH] Treble tone controller, adjust the controller to enhance or attenuate for
15dB at 12KHz.
6.[MID] Alto tone controller, adjust the controller to enhance or attenuate for
15dB at 2.5KHz.
7.[LOW] Bass tone controller, adjust the controller to enhance or attenuate for
15dB at 80Hz.
8.[FX] Controller, adjust the signal level from the channel to the reverberation line.
Please note, the single level will vary with the different setting of the channel
attenuator. If using the stereo channel, will mix the signals from L and R channels,
then, send it to reverberation line.
4 CHANNEL 6 CHANNEL 8 CHANNEL
1. The external power input socket, receiving external power supply, DC +15V, -15V, +48V,
ground wire
2. Power Switch
GENERAL SPECIFICATIONS
MP3 MODULE FUNCTION
A .USB insert
B.The power indicator
C.Play or Pause
D.Select to play next song
1
2
3
4
5
6
7
8
9
10
1
2
A B C D E
4 CHANNEL
6 CHANNEL
8 CHANNEL
Input channels
Mono:MIC/LINE
2
2
4
Stereo:LINE
1
2
2
MP3
1
1
1
USB sound card
TAPE/CD Input
1
1
1
Output
channels
STEREO OUT
1
1
1
PHONES
1
1
1
RETURN
Bus
STEREO
1
1
1
SEND
1
1
1
Input Channel
Function
PAD
26dB
EQ
HIGH Gain +15dB/-15dB Frequency 12kHz
shelving MID Gain +15dB/-15dB Frequency
2.5kHz shelving LOW Gain +15dB/-15dB
Frequency 80kHz shelving
PEAK LED
LED turns on when post EQ signal reaches 3
dB below clipping level
Level Meter
2*5-segment LED meter,(+6,+3,0,-3,-10 dB)
Effects
Built-in
Built-in
Built-in
Phantom Power Voltage
+48V
Power Requirements
AC 100-240V,50/60Hz DC +15V,-15V,+48V
Power Consumption
20W
20W
20W
1.[MIC/LINE] Mono input, connect the microphone, musical instrument or
audio device (CD player and so on) to the device. The sockets are supporting
both XLR and UNBALANCED 1/4" PLUG.
2.[+48V PHANTOM] Button/LED, when the button is turned on, the LED light is
on, provide DC+48V phantom power to XLR plug on MIC/LINE mono input.
Please turn on this button when using the condenser microphone which is
powered by a phantom power.
3.[PAD] button, it will attenuate the sound input to the device when turn on
this switch. You can turn on the switch if you hear the distortion or [PEAK]LED
(9) indicator light is on.
4.[GAIN] Controller, determines the basic volume of each channel, adjust
them for the maximum volume performance, when the volume gets too loud,
the [PEAK]LED (9) indicator light will keep flashing.
5.[HIGH] Treble tone controller, adjust the controller to enhance or attenuate
for 15dB at 12KHz.
6.[MID] Alto tone controller, adjust the controller to enhance or attenuate for
15dB at 2.5KHz.
7.[LOW] Bass tone controller, adjust the controller to enhance or attenuate for
15dB at 80Hz.
8.[FX] Controller, adjust the signal level from the channel to the reverberation
line. Please note, the single level will vary with the different setting of the
channel attenuator. If using the stereo channel, will mix the signals from L and
R channels, then, send it to reverberation line.
9.[PEAK] LED indicator light, when the volume of input signal or volume after
adjusting equalizer is too high, the LED indicator light will keep flashing, please
rotate the [GAIN] CONTROLLER counterclockwise to turn down the volume.
10.[LEVEL] Controller, adjust to balance the volume of each channels.
USER´S
MANUAL
MG MG MG04 USB / 06 USB / 08 USB
9 2
9.[PEAK] LED indicator light, when the volume of input signal or volume after adjusting
equalizer is too high, the LED indicator light will keep flashing, please rotate the [GAIN]
CONTROLLER
10.[LEVEL] Controller, adjust to balance the volume of each channels.
MAIN CONTROL
1. USB interface and MP3 display.
2. [+48V PHANTOM] Button/LED, when the button is
turned on, the LED light is on, provide DC+48V phantom
power to XLR plug on MIC mono input. Please turn on
this button when using the condenser microphone which
is powered by a phantom power.
3. Converting switch for "Channel " and "USB signal".
4.Channel input socket (stereo), 8CH mixer with two
group of input socket, 4CH and 6CH mixers with one
group of input socket. If only connect to L (MONO)
socket, the mixer will send out the same mono signal to L
and R sockets.
5. [TAPE/CD IN] TAPE/CD signal input socket
1. [MAIN OUT] Output, connect the active speaker or amplifier.
2. [SEND&RETURN] Socket, when using the [SEND] output socket
separately, can be connected with power amplifier, act as the
monitoring signal. When using the [RETURN] input socket
separately, can be connected with the audio source. When
using two sockets together, can connect with the external audio
processor.
3. [PHONES]Output socket, connect an earphone, the socket is
stereo phone plug.
1. Level indicators can show the signal level from
[STEREO OUT] output. Adjust the LEVEL] controller to
lower the level if [PEAK] indicator light up in RED.
2. [DELAY] Controller, adjust the depth of the
reverberation.
3. [REPEAT] Controller, adjust the repetition times of the
reverberation.
4. [FX LEVEL] Effects return level controller, adjust the
volume of effect.
5. [LEVEL PHONES] Earphone controller, adjust the
volume of earphone.
6. [STEREO LEVEL] Fader, adjust the overall volume
from [STEREO OUT] output signal.
CHANNEL INPUT
4 CHANNEL 6 CHANNEL 8 CHANNEL
1
2
3
4
5
6
7
8
9
10
1
4
2 3
5
6
8
7
1
5
2
3
4
1
3
2

Product specificaties

Merk: Audibax
Categorie: Mengpaneel
Model: MG08 USB

Heb je hulp nodig?

Als je hulp nodig hebt met Audibax MG08 USB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Mengpaneel Audibax

Audibax

Audibax 202 Go Handleiding

2 November 2024
Audibax

Audibax MG08 USB Handleiding

2 November 2024
Audibax

Audibax MG06 USB Handleiding

2 November 2024
Audibax

Audibax MG04 USB Handleiding

2 November 2024
Audibax

Audibax MG05 XU Handleiding

2 November 2024

Handleiding Mengpaneel

Nieuwste handleidingen voor Mengpaneel

Martin

Martin 2518 DMX Handleiding

17 November 2024
NutriBullet

NutriBullet Ultra 1200 Handleiding

16 November 2024
Mackie

Mackie ProFX12 Handleiding

15 November 2024
Solid State Logic

Solid State Logic SSL UF1 Handleiding

15 November 2024
Yamaha

Yamaha IM8-32 Handleiding

14 November 2024
Yamaha

Yamaha IM8-40 Handleiding

14 November 2024
Yamaha

Yamaha DCU5D Handleiding

14 November 2024
Yamaha

Yamaha SP02R96 Handleiding

14 November 2024
Yamaha

Yamaha MG166C-USB Handleiding

13 November 2024
RCF

RCF L-PAD 12C Handleiding

5 November 2024