Atdec VF-AT Handleiding

Atdec Niet gecategoriseerd VF-AT

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec VF-AT (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 201 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installation Instructions

VF-AT

Component Checklist

Focus | Articulated Arm

M4x10/12/16mm (x4)

Phillips Head Mounting Screws

Primary Arm

Cable Cover

Cable Stops

(x2)

Pole Top Cap Cable Clip

Secondary Arm

Cable Cover

M8x30mm

Screw

Bolt Through

Base

Steel Washer

Arm Assembly

Pole Assembly Desk Clamp Assembly

5mm Allen Key

HARDWARE Display Mounting

Screws

! IMPORTANT - Install Visidec Focus Articulated Arm as per installation instruction.

! This product supports a maximum load of 8kg (17.6lbs).

! The manufacturer accepts no responsibility for incorrect installation.

IMPORTANT INFORMATION:

Step 1. Check Components

Check what you have received against the component checklist and hardware above.

Step 2. Mount Pole Assembly

Option 1 Option 2: Bolt Through : Mount using Desk Clamp

Pole Assembly

Pressure Plate

2.1 Remove both the Pressure

plate and M10 Desk Clamp

Screw.

2.2 Fasten the Desk Clamp to the Bolt

Through Base & Pole Assembly using the

M8 x 30mm Screw and Tighten Firmly.

M10 Desk Clamp

Screw

M8 x 30mm Screw

Bolt Through Base

Pole Assembly

Slot

Slot Tab

Bolt Through Base

Steel Washer

M8x60mm Screw

5mm Allen Key

It is recommended that the Pole Assembly be

mounted towards the rear edge of the work surface.

Note: Ensure that the Slot Tab in the Bolt

Through Base fits snugly into the Slot on the

Pole Assembly.

The Visidec logo on the Bolt Through Base

must face the of this assembly.front

5mm Allen Key

M8x60mm

Screw

Step 2. Mount Pole Assembly (cont.)

Step 3. Mount Arm Assembly

2.4 Remove the M8 x 16mm Socket Head Countersunk

Screws to release the Desk Clamp Bracket.

2.3 The Desk Clamp bracket can be repositioned to suit different mounting

surface thicknesses. The maximum mounting surface thicknesses supported

are listed below from the Top to Middle and Bottom Screw Holes.

T TM MB B

M8 x 16mm Socket

Head Countersunk

Screw

5mm Allen Key

Desk Clamp Bracket Pressure Plate

Table Top

M8 x 16mm Socket

Head Countersunk

Screw

M10 Desk Clamp Screw

5mm Allen Key

Arm Assembly

Pole Top Cap

2.5 Place in desired

location.

If you need to reposition the desk clamp bracket or you have no

access to the rear of your table continue to . Step 2.4

If you DO NOT need to reposition the desk clamp bracket and

you have access to the rear of your table skip to .Step 2.7

2.6 Reattach Desk

Clamp Bracket.

2.7 After positioning

your Pole Assembly,

screw Pressure Plate in

and Tighten Firmly.

3.1 Unlock Handgrip

and raise so that

Handgrip Tab

protrudes.

3.2 Slip the Arm

Assembly over the

Handgrip Tab and then

onto the Pole.

3.3 Slide the Arm

Assembly and Handgrip

down the pole before

locking the handgrip at

the desired height.

3.4 Insert Pole Top

Cap into Pole. This is

also where the Allen

Key is stored.

Desk Clamp Bracket

Handgrip Tab

Top 0 - 32mm (default)

Middle 7 - 47mm

Bottom 22 - 62mm

Top 29 - 69mm

Middle 43 - 84mm

Bottom 59 - 99mm

6.2 Cable Clips and Cable Stops can be

installed to further manage cables.

Please See Over.

Step 4. Mount Displays

Step 5. Adjust Height

M4 Phillips Head

Mounting Screws

Option 1: 75x75mm Hole Pattern 100x100mm Hole PatternOption 2:

Note: Extend Arms to

achieve 100x100mm

hole pattern.

5.1 Unlock Handgrip ensuring both the

screen and arm assembly are supported.

5.2 Lift/Lower the Screen to the desired height.

Move both Screen and Arm assembly together.

Step 6. Cable Management

6.1 After plugging in your cables, install the Cable Covers.

A. Insert Cable Covers up

into Lock Slots.

B. Push Cable Covers away

from Elbow Joint to secure

in place.

Elbow Joint

‘click’

Lock Slot

Cable Stop

Cable Clip

5.3 Lock Handgrip firmly.

Note: Ensure enough cable

slack is given to allow for

movement.

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	VF-AT
Montagewijze:	Bureau
Maximale gewichtscapaciteit:	8 kg
Draaihoek:	360 °
Pan bereik:	0 - 180 °
Bereik kantelhoek:	0 - 70 °