Atdec AWM-AHX-S Handleiding

Atdec Niet gecategoriseerd AWM-AHX-S

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec AWM-AHX-S (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

AWM-AHX Page 1 of 3

Installation Guide

AWM-AHX

Heavy Duty Dynamic Arm

COMPONENT CHECKLIST REQUIRED TOOLS

All tools supplied

Lower Angled

Link

(x1)

Heavy Duty

Dynamic Link

(x1)

4mm

Allen Key

(x1)

WEIGHT RANGE

Desk Base Mount

6 - 16kg

(13 - 35 )lb

Post Mount

6 - 14kg

(13 - 31 )lb

Monitor weight should be

within the weight range of

all modular elements that

make up the complete

monitor mounting solution.

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed

the capacity of the mount even though the monitor weight may be within the stated range.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with AWM Series monitor arm products.

AWM-AHX Page 2 of 3

1.1 Push two arm links together

2.1 Push arm onto shaft

3.1 Push link

onto shaft

3.2 Ensure link

is fully pushed

onto shaft

3.3 Tighten set screw

1.2 Ensure arm is fully pushed together

2.2 Ensure arm is fully pushed onto base

1.3 Tighten set screw

2.3 Tighten set screw

1. Assemble Arm Links

2. Fit arm onto Arm Base (AWM-LB) or Channel Clamp (AWM-LC) (sold separately)

3. Fit Heavy Duty Tilt Head (AWM-LTH) or Dual Crossbar (AWM-LR) (sold separately)

Note: Check that arm rotation

is smooth after tightening

Note: Check that arm rotation

is smooth after tightening

Note: Check

rotation is smooth

after tightening

Optional: Set joint

rotation to 180°

on Arm Base or

Channel Clamp by

following separate

instruction manual.

To set up follow

separate installation

guide supplied with

the Dual Crossbar

Dual Crossbar

AWM-LR

Heavy Duty VESA Tilt Head

AWM-LTH

To set up follow

separate installation

guide supplied with the

Heavy Duty Tilt Head

AWM-AHX Page 3 of 3

Heavier

Monitor

Push

& Hold

Lighter

Monitor

4. Adjust arm tension

4.1 Use the provided allen key to adjust the arm tension

NOTE:

Hold arm in horizontal

position when adjusting

4.3 If the monitor sags or falls down,

increase the arms tension by rotating

the screw anti-clockwise.

4.5 If the monitor oats or hovers in all

positions the arm tension is balanced and

does not require further adjustment.

4.4 If the monitor springs upwards,

decrease the arms tension by rotating

the screw clockwise.

4.2 Installing multiple similar monitors?

1. Set up one monitor and record the

position of the marker on the gauge.

2. When installing other similar monitors,

pre-tension the arm to the recorded

marker position then ne-tune the

tension by following steps .4.3 to 4.5

Marker

Monitor Falls

(from top)

Increase Tension

Monitor ‘Floats’

(all positions)

Balanced

Monitor Springs

(from bottom)

Reduce Tension

5. Cable management

5.1 Plug cables into the monitor and

route the cables down the arm using

the cable hooks and clips.

Important!

Ensure enough

cable slack is given

in this area to allow

for movement of

the monitor.

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	AWM-AHX-S
Kleur van het product:	Zilver
Breedte:	597 mm
Materiaal behuizing:	Aluminium
Maximale gewichtscapaciteit:	16 kg
Compatibiliteit:	AWM-LTH, AWM-LR
Draaihoek:	180 °
Verbeterd kabelbeheer:	Ja
Type product:	Flatscreen bevestigingsarm
Minimale schermgrootte:	43 "