Atdec SD-POS-HA Handleiding

Atdec Niet gecategoriseerd SD-POS-HA

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec SD-POS-HA (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Component Checklist

3/2.5mm

Allen Key (x1 each)

M4x12mm (x4)

M4x16mm (x4)

POS Assembly (x1)

Screw Cover (x1)

VESA Plate (x1)

Top Cap (x1)

M5 Grub Screw (x1)

14 Gauge

Screws (x4)

Installation

Template (x1)

M4x10mm (x4)

180

270 355

Gap in

Rotation

90 180

270

355

Gap

in Rotation

USER USER

Direction

Arrow

Direction Arrow

LOCKING HOLES

Direction Arrow

Locking Hole (Fixed)

0-90

Locking Hole

0-180

Locking Hole

0-270

Locking Hole

Base Plate

M5 Grub Screw

2.5mm Allen Key

3mm (0.12")

Pilot Holes

45mm

(1.75") Cable

Access Hole

14 Gauge

Screws (x4)

INSTALLATION

TEMPLATE

3mm (0.12")

USER

Security Screw (x1)

Installation Instructions

SD-POS-HA

Display l POS Height Adjustable

IMPORTANT INFORMATION:

Step 1. Check Components

Step 2. Limit Rotation

Step 3. Locate and Secure your POS Height Adjustable

! IMPORTANT - Install Spacedec POS Height Adjustable as per Installation Instructions.

! This product supports a maximum load of 20kg (44lbs).

! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.

! The height adjustment range (from desk level to the centre of the screen) 330-450mm (12.99"-17.72").

Display Mounting

Screws

Hardware

Your SD-POS-HA offers 355°

of Rotation. This can also be

limited to suit a specific

application. The direction in

which you mount SD-POS-HA

will determine where the 5°

gap in rotation is located,

and how you choose to limit

the rotation.

Determine the degree of rotation

you require

(refer to Mounting Options above).

To limit the rotation, use the

2.5mm Allen Key to insert the

supplied M5 Grub Screw into your

chosen Locking Hole until it sits

flush with the Base Plate.

NOTE: If you want the full

355° rotation, you do NOT

need to install a grub screw.

Mounting Options

Rotation Options

0° Rotation (Fixed)

0-90° Rotation

0-180° Rotation

0-270° Rotation

0-355° Rotation

Position the Installation Template in the desired

location on your work surface. Ensure the straight

edge sits perpendicular with the User’s line of

sight. Mark the center points of each of the

required holes onto the work surface with a pencil.

Drill 4 x 3mm (0.12") Pilot Holes to a depth of

15mm (0.59"). Use a 45mm (1.75") hole saw to

drill the Cable Access Hole in the work surface.

Reposition SD-POS-HA with the “Direction Arrow”

pointing in the direction required for your chosen

rotation. Secure the SD-POS-HA to the work surface

using the supplied 14 Gauge Screws (x4).

Check you have received all parts against the component checklist and Hardware above.

Pilot Holes

Cable Access Hole

NOTE: Philips-head

screwdriver not supplied

Centre for 45mm (1.75")

(optional)

! The minimum thickness of the mounting surface is 15mm (0.59") when using the manufacturer supplied Hardware.

! The manufacturer accepts no responsibility for incorrect installation.

Screw Cover

Top Cap

PUSH

Hand Grip

Push out to remove

Cable Access Cap

CABLE

ACCESS CAP

PUSH

Pull cables out through

Rear Cable Access Port.

VESA Plate

Mounting Screws (x4)

Installation Complete

Step 6. Install Top Cap

No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 03.07.13

Step 4. Attach Screw Cover

Step 8. Install Monitor Cables

Step 10. Attach your Display to the POS Assembly

Step 11. Adjust the VESA Ball Mount

Remove the paper backing from the Screw

Cover and adhere to the base as shown.

Loop the Security Cable (Kensington or

similar) around the internal post of the

POS Assembly.

Feed the other end of the cable through

the POS Assembly and out the Cable

Management Hole.

After you have attached the monitor

(As directed in Step 9) install the lock to the

monitor as per the manufacturer

guidelines.

Note: Security Cable Not Included

Step 7. Adjust Pole Height

Step 5. (Optional)

Install Monitor Security Cable

Step 8. Install Monitor Cables

Push down firmly to attach the Top Cap.

Prior to attaching your monitor,

install the monitor cables.

Run them through the Front

Cable Access Port, down the

pole and out of the Cable

Access Hole in the work

surface.

Loosen Hand

Grip.

Set to desired

Height

Tighten Hand Grip

to lock pole at

desired height.

LOOSEN

TIGHTEN

TO LOCK

ADJUST

HEIGHT

Option 2: When you do not want to route the cables

below the work surface.

Step 9. Attach the VESA Plate to your Display

These Installation Instructions secure

the SD-POS-HA using the provided

fasteners from the above work surface.

For advanced Security Installation from

below the work surface. Please refer to

the

Advanced Security Installation

Addendum.

Advanced Security Installation

OUT

Option 1:

There are two mounting

hole configurations:

• 75 x 75mm

• 100 x 100mm

Choose appropriate

Mounting Screws from

the Hardware supplied

to suit your Display.

75mm 75mm

100mm

Back of Display

Top of

Display

HOOK

Back of Display

Quickshift Mount.

Hook the top of the VESA plate onto the

Press and hold the Release Buttons. Gently

push bottom of VESA Plate into Quickshift

Mount. Release Buttons to lock in place.

PUSH

Release Button Back of Display

Insert the Security Screw, and

tighten using a Phillips-head Screwdriver

TIGHTEN

Phillips-head

Screwdriver

Security Screw

Back of Display

Position your Display to the desired viewing angle using the 40 °

angular movement allowed by the VESA Ball Mount.

If the display does not hold its position, or is too

resistant, adjust the Tension Plate located at the

rear of the VESA Ball Mount.

To make any adjustments, use the 3mm Allen Key

supplied. Apply half a turn at a time to each screw

on the Tension Plate to adjust evenly.

Check the display, and the adjust again if necessary.

Tension Plate

3mm Allen Key

TIGHTEN (+kg)

LOOSEN (-kg)

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	SD-POS-HA
Kleur van het product:	Zwart
Hoogte:	17.91 "
Montagewijze:	Vloer
Maximale gewichtscapaciteit:	20 kg
Montage interface compatibiliteit (min):	75 x 75 mm
Montage interface compatibiliteit (max):	100 x 100 mm
Minimale schermgrootte:	- "