Astralpool ZX Series Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Astralpool ZX Series (8 pagina's) in de categorie Waterfilter. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
INSTALLATION AND
OPERATING INSTRUCTIO NS
Melbourne: 03 8796 8600 Gold Coast: 07 5552 2600 Perth: 08 9350 2600
Sydney: 02 9853 2100 Townsville: 07 4750 3100 sales@astralpool.com.au
Brisbane: 07 3308 5400 Adelaide: 08 8152 7600 www.astralpool.com.au
INSTALLATION AND OPERATING INSTRUCTIONS I INSTALLATION AND OPERATING INSTRUCTIONS
ZX Series Cartridge
Filter
INST 247 ZX Series Cartridge Filter 7. V0 20
2
INST 247 ZX Series Cartridge Filter 7. V0 20
3
INTRODUCTION
Congratulations on the purchase of your AstralPool ZX series cartridge filter.
The ZX series filters are made to last by utilising the best quality materials available. The tank is made from high quality
ABS plastics, capable of withstanding the harshest of environments while DuPont Remay elements are used which are
regarded by the industry as the best available. Include with this Mircoban antimicrobial coating on the elements and
you are sure to achieve one of the cleanest pools possible.
WARNING: DO NOT OVERTIGHTEN LOCKING RING AS THIS MAY CAUSE THE FILTER TO LEAK. GENTLE HAND
TIGHT IS SUFFICIENT FOR CORRECT SEALING.
INSTALLATION OF ZX SERIES
1. Ensure cartridge filter is located on a clean, stable and level base.
2. The ZX series filter has three inlet ports (from pump) and one outlet port (to pool/spa). Glue one of the 50mm slip
tails supplied into one of the inlets and second slip tail supplied into the outlet of the filter that suits the plumbing
configuration.
3. Glue in the supplied blanking cap and drain plug cap into the two remaining inlets. Allow a minimum of one hour
for glue to dry before subjecting filter to system pressures.
4. Glue water connection pipes from pump and pool return to 50mm tails supplied. (Ensure locking nut is placed on
pipe before gluing on tails.
5. Apply Teflon tape (not included) to the pressure gauge and screw into lid where indicated.
START UP INSTRUCTIONS
1. Before starting your ZX filter, make sure the cartridge is in the filter and the lid and lock ring are in place anup d
tightened.
2. Open the suction and return line valves (when fitted).
3. Start pump and open the air release valve on the filter lid 2 to 3 turns air will begin to be forced from the tank. –
Once water begins to flow from the valve, tighten to close. Check there is a good flow of water back in the pool. to
4. Clean the cartridge when the flow to the pool reduces or the pressure gauge increases by 15 20 kPa. –


Product specificaties

Merk: Astralpool
Categorie: Waterfilter
Model: ZX Series

Heb je hulp nodig?

Als je hulp nodig hebt met Astralpool ZX Series stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Waterfilter Astralpool

Handleiding Waterfilter

Nieuwste handleidingen voor Waterfilter

Fluval

Fluval U2 Handleiding

3 December 2024
Fluval

Fluval C3 Handleiding

3 December 2024
Fluval

Fluval 407 Handleiding

3 December 2024
Fluval

Fluval U4 Handleiding

3 December 2024
Fluval

Fluval U3 Handleiding

3 December 2024
Philips

Philips ADD6830 Handleiding

24 November 2024
Puretec

Puretec CFS4000 Handleiding

19 November 2024
Laica

Laica H0M Handleiding

19 November 2024
Laica

Laica C3M Handleiding

18 November 2024