Astralpool APV800 Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor Astralpool APV800 (4 pagina's) in de categorie Waterfilter. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
INSTALLATI
INSTALLATI
INSTALLATI
INSTALLATIINSTALLATION AN
ON AN
ON AN
ON ANON AND
D
D
D D
OPERATI
OPERATI
OPERATI
OPERATIOPERATING INSTRU
NG INSTRU
NG INSTRU
NG INSTRUNG INSTRUCTIO
CTIO
CTIO
CTIOCTIO
NS
NS
NS
NSNS
www.astralpool.com.au
sales@astralpool.com.au
INSTALLATION AND OPERATING INSTRUCTIONS I INSTALLATION AND OPERATING INSTRUCTIONS
FG Bobbin Wound
Fibreglass Sand Filters
FG Bobbin Wound Fibreglass Sand Filter V08. 20
2
Capacit
Capacit
Capacit
CapacitCapacity Table
y Table
y Table
y Table y Table
MODEL
MODEL
MODEL
MODEL MODEL
DIAMETER
DIAMETER
DIAMETER
DIAMETER DIAMETER
FILTER AREA
FILTER AREA
FILTER AREA
FILTER AREA FILTER AREA
6 HR TURNOVER
6 HR TURNOVER
6 HR TURNOVER
6 HR TURNOVER 6 HR TURNOVER
8 HR TURNOVER
8 HR TURNOVER
8 HR TURNOVER
8 HR TURNOVER 8 HR TURNOVER
MEDIA
MEDIA
MEDIA
MEDIA MEDIA
REQUIRED
REQUIRED
REQUIRED
REQUIRED REQUIRED
FG 604
FG 604
FG 604
FG 604 FG 604
60 0 mm (24”)
0.29 Sq M
85,000ltrs(22,500g)
114,000ltrs(30,000g)
150 kg(330 Ibs)
FG 705
FG 705
FG 705
FG 705 FG 705
700 mm (26 ”)
0.38 Sq M
130,000ltrs(34,000g)
173,000ltrs(46,000g)
200 kg(440Ibs)
FG 805
FG 805
FG 805
FG 805 FG 805
800 mm (31 ) ”
0.43 Sq M
144,000ltrs(38,000g)
192,000ltrs(51,000g)
330 kg(727Ibs)
FG 905
FG 905
FG 905
FG 905FG 905
900 mm (35”)
0.65 Sq M
180,000ltrs(47,500g)
240,000ltrs(63,400g)
410 kg(903Ibs)
GENERAL NOTES
GENERAL NOTES
GENERAL NOTES
GENERAL NOTES GENERAL NOTES
1. When unpacking the filter, be sure the unit is complete and no visible shipping damage has occurred.
2. Allow sufficient clearance around filter system for access and maintenance. If installed in a plant room, ensure there
is sufficient access to remove filter at a later date.
3. Provide adequate ventilation for pumping equipment, installed in conjunction with filter.
4. Provide solid mounting for filter and pump. If installed outdoors, install the system on a slab or solid concrete base
to avoid risk of settlement. Filter systems once located with media can exceed a weight of 500 kg. Pump, filter and
other connecting equipment should be located on the same slab.
5. Installation of filters and pumps should be located as close to the pool as possible to avoid excessive piping friction
loss.
6. If system is installed below pool level it is important to install isolating valves to prevent risk of flooding from back
up water, from the pool or spa.
7. The proper media selection is critical to good filter performance. Ensure that the media is an approved Quartz
Silica with a sizing range of 0.4 to 0.55 mm.
8. The installation of filters requires no special tools. An Al n key is provided with the filter to tighten the multiport le
valve clamps.
9. Confirm that plumbing lines from pool are correctly identified. This will ensure proper connection to markings on
filter valve (i.e. β€œPump”, β€œWaste”, and β€œReturn”).
10. The tank should be situated in such a way to allow easy access to on underside of filter. winter
winter
winter
winter winter drain
drain
drain
drain drain
LOADING FILTER MEDIA
LOADING FILTER MEDIA
LOADING FILTER MEDIA
LOADING FILTER MEDIA LOADING FILTER MEDIA
Once the filter system has been positioned, the installation of filter media may be undertaken as follows:
1. Check filter size in order to determine necessary amount of media required.
2. Double check that the internal system consisting of a lateral hub and stand pipe are intact inside the tank.
3. Fill tank half full with water.
4. Place the disposable metal loading disc into the upper tank opening and the plastic cover over stand pipe to stabilise
the filter and stand pipe. It is important that the stand pipe remains centered through the media loading procedure
to ensure alignment with valve assembly opening.
5. Proceed to load correct volume of dry media slowly (if media is saturated loading can be difficult). Generally, a
coffee can or funnel, can aid in the loading process.
6. Once media is loaded discard loading disc and check to determine if stand pipe is properly centred in tank opening.
Dimens
Dimens
Dimens
DimensDimensions With Val
ions With Val
ions With Val
ions With Valions With Valve Installe
ve Installe
ve Installe
ve Installeve Installed
d
d
d d
Model
Height
Width
Shipping Weight
FG 604
FG 705
FG 805
FG 905
98 8.5 cm (3 ”)
105 ( cm 41”)
115 5.5 cm (4 ”)
12 507 (cm ”)
60 4 cm (2 ”)
70 6 cm (2 ”)
80 1 cm (3 ”)
90 5 cm (3 ”)
22 kg (49 Ibs)
32 kg (71 Ibs)
38 kg (84 Ibs)
45 kg (99 Ibs)
FG Bobbin Wound Fibreglass Sand Filter V08. 20
3
INSTALLATION OF SELECTOR VALVE
INSTALLATION OF SELECTOR VALVE
INSTALLATION OF SELECTOR VALVE
INSTALLATION OF SELECTOR VALVEINSTALLATION OF SELECTOR VALVE
1. Following the media loading, clean any media particles or debris from upper surface of tank opening.
2. Install six (6) position selector valve after placing in cavity in underside of valve body. Place valve into tank
O
O
O
OO-Rin
-Rin
-Rin
-Rin-Ring
g
g
gg
opening while ensuring that the has remained in position.
O
O
O
OO-Ring
-Ring
-Ring
-Ring -Ring
3. Install selector valve into top tank opening and rotate valve to best suit plumbing lines. Once positioned, fit clamp
band assembly around neck of filter and valve and tighten sufficiently for good engagement. N
N
N
NNote: A
ote: A
ote: A
ote: Aote: An Al
n Al
n Al
n Aln Al n key is
n key is
n key is
n key is n key is
le
le
le
lele
provided to t
provided to t
provided to t
provided to tprovided to tighte
ighte
ighte
ighteighten the bolts in t
n the bolts in t
n the bolts in t
n the bolts in tn the bolts in the clam
he clam
he clam
he clamhe clamp band.
p band.
p band.
p band.p band.
4. Double check that incoming pool lines are connected to appropriate valve openings as marked on valve port (i.e.
pump, return (pool) and waste).
5. The threaded openings on valve are 40mm or 50mm thread which all accommodate Astralpo barrel unions ol
supplied with MPV. O-rings are supplied to fit between the multiport valve and barrel union. It is only necessary to
tighten by hand.
The use
The use
The use
The useThe use of Teflon ta
of Teflon ta
of Teflon ta
of Teflon ta of Teflon tape is not req
pe is not req
pe is not req
pe is not reqpe is not required.
uired.
uired.
uired.uired.
6. Remove white plug from side wall of valve and install threaded pressure gauge using Teflon tape wrap (do
do
do
dodo not o
not o
not o
not o not over
ver
ver
ver ver
tighten
tighten
tighten
tightentighten). Minimum hand tightening is adequate to provide a good seal.
VALVE OPERATION
VALVE OPERATION
VALVE OPERATION
VALVE OPERATION VALVE OPERATION
The operation and the positions of valve settings are as follows:
Valve Set
Valve Set
Valve Set
Valve SetValve Settings
tings
tings
tings tings
Directio
Directio
Directio
DirectioDirection of flow thro
n of flow thro
n of flow thro
n of flow thron of flow through Valve
ugh Valve
ugh Valve
ugh Valveugh Valve
Filter (also during vacuuming)
From pump down through valve, through sand bed,
up through stand pipe to valve and back through
pool return.
Back Wash
From pump, through valve, down through stand
pipe, up through sand bed, and through valve to
waste.
Rinse
Flow from pump, through valve, down through sand
bed, up through stand pipe, through valve to waste.
(Position also used for initial start-up and leveling
sand bed after Back-wash)
Waste
From pump, through valve to waste. Also position
for lowering water level or assist in draining pool.
Closed
From pump to valve without further circulation.
Prevents any flow to filter and pool.
Recirculate
From pump through valve to pool. This position bi-
passes the filter and is used for circulation of pool
water only.
NOTE: A
NOTE: A
NOTE: A
NOTE: ANOTE: Always β€œSTO
lways β€œSTO
lways β€œSTO
lways β€œSTOlways β€œSTOP” pump whe
P” pump whe
P” pump whe
P” pump wheP” pump when changing sele
n changing sele
n changing sele
n changing selen changing selector valve
ctor valve
ctor valve
ctor valve ctor valve position.
position.
position.
position.position.


Product specificaties

Merk: Astralpool
Categorie: Waterfilter
Model: APV800

Heb je hulp nodig?

Als je hulp nodig hebt met Astralpool APV800 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Waterfilter Astralpool

Handleiding Waterfilter

Nieuwste handleidingen voor Waterfilter

JANDY

JANDY CS250 Handleiding

18 December 2024
JANDY

JANDY CS150 Handleiding

18 December 2024
JANDY

JANDY CS100 Handleiding

18 December 2024
Heissner

Heissner HLF6000 Handleiding

16 December 2024
Haier

Haier HRO4H85-3 Handleiding

10 December 2024
Haier

Haier HRO6H85-3 Handleiding

10 December 2024
Haier

Haier HBWS-S15 Handleiding

10 December 2024
Haier

Haier HBCF-S3002 Handleiding

10 December 2024
Haier

Haier HBP-V40 Handleiding

10 December 2024