Astralpool Olot Handleiding
Astralpool
Waterfilter
Olot
Lees hieronder de đź“– handleiding in het Nederlandse voor Astralpool Olot (37 pagina's) in de categorie Waterfilter. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/37
BOBBIN FILTERS
FILTRES BOBINÉS
FILTROS BOBINADOS
FILTRI BOBINATI
FILTROS BOBINADOS
FILTRY ZWOJONE
INSTRUCTIONS AND OPERATION MANUAL
MANUEL D´INSTRUCTIONS ET DE FONCTIONNEMEN
MANUAL DE INSTRUCCIONES Y FUNCIONAMIENTO
MANUALE DI ISTRUZIONI E FUNZIONAMENTO
MANUAL DE INSTRUÇÕES E FUNCIONAMENTO
INSTRUKCJA OBS UGI I DZIA ANIA
"In order to archive optimum performance from your filter, please see the following instructions".
1. CHECK THE PACKAGING
Check that the filter and all its components are in good condition after transportation.
There is a box with the filter, which contains pressure gauges, along with other accessories. There will also be a guarantee and test certificate.
2. GENERAL SPECIFICATIONS
Filters are the most important part of a water filtration system, and their function is to remove suspended solids and clarify the water.
The effect of correct filtration will influence the results of disinfectant process.
The principle of filtration involves retaining the suspended particles that the water tries to carry with it through the filter sand bed.
The water treatment process involves a range of equipment besides filters, such as; pumps, chemical dosing, pool shell fittings, which ensure the
correct suction and return of water, which with the rest of the equipment ensures the correct circulation and maintenance of the water quality.
Whilst standards are approaching homologation throughout Europe, each country normally has its own standards, regulations or recommendations
governing private and public pools, and installers should adhere to these when designing and installing any system. All designs and all materials used
must meet the relevant standards.
The filtration quality may depend on different factors: Design of the filter, type of collector used - collectors or nozzles, media bed depth,
specifications and density of the filtering material etc. At the same time the filtration velocity is a determining factor when seeking good quality
filtration and a velocity of no more than 40 m/h is recommended.
Bobbin filters are manufactured from polyester resin and glass fibre materials, which have excellent anticorrosive properties. The interior includes a
collector and diffuser made from PVC and PP plastic. They are also resistant to salt water and can operate up to a maximum temperature of 50ÂşC.
The special layer of isopthalic resin on the interior of the filter gives it maximum durability against wear and tear and abrasion, also enabling it to be
used with potable water. Filters may also be manufactured on request with a vinylester lining, which is resistant to most chemicals including ozone.
3. IDENTIFICATION OF COMPONENTS
A) Filters with laterals (FIG.1)
1. Lid for addition of media, and inspection.
2. Air relief valve
3. Pressure gauge
4. Sight glass (optional, on request)
5. Reinforced polyester and fibre glass tank
6. Dirty water inlet
7. Clean water outlet
8. Water collected via laterals
9. Reinforced polyester and fibre glass base
10. Manual water drainage
11. Sand discharge cap
12. Side man hole (optional, on request)
13 Filtration media
14. Water diffuser system
15. Eyebolt to transport the filter (only for use when the filter is empty)
B) Filters with nozzle plates (FIG.2)
1. Lid for addition of media, and inspection.
2. Air relief valve
3. Pressure gauge
4. Sight glass (optional, on request)
5. Reinforced polyester and fibre glass tank
6. Dirty water inlet
7. Clean water outlet
8. Water collected via nozzle plate
9. Reinforced polyester and fibre glass base
10. Manual water drainage
11. Air inlet connection for backwash
12. Side man hole and sand discharge
13. Filtration media
14. Water diffuser system
15. Eyebolt to transport the filter (only for use when filter is empty)
IMPORTANT: The instruction manual that you have in your hands contains fundamental information on the necessary security measures which
need to be adhered to when installing and commisioning the filter. It is therefore essential that both the installation engineer and the end user read
these instructions before proceeding any further.
ENGLISH
1
BATTERY ASSEMBLY:
4. INSTALLATION SPECIFICATIONS
•In order to achieve successful installation it is important to consider the following points:
•Choose a pump suitable for the required flow at 10 m head (water).
•In order to backwash the filter, the system of pumps and filters must combine to obtain the necessary flow, which can be from 40 - 50m/h
lateral models, and up to 60 m/h for nozzle plate models.
•To scour the filter with air (nozzle plate models or models with double laterals) it will use one or more air blower or capable of supplying air at
a velocity of 60 m/h 300 mbar. Never use a compressor because damage could occur due to excessive pressure.
•It is advised to install the filters below the level of, and as close to the pool as possible.
•The plant room where the filters are installed should be well ventilated and have the necessary drainage channels available to allow escape
of water, should a pipe, filter or pump leak in the case of an accident, preventing damage to any equipment. If it is not possible to install such
drainage measures then an alternative automated system (e.g. submersible pumps) should be installed for water removal.
5. INSTALLATION
Filters are delivered packaged and palleted, due to their weight and volume. This can make them difficult to manoeuvre around the building site
and install so it is recommended that they be transported by fork lift, crane etc.
Filters are made of plastic, and although they are designed to be resist to internal pressure, they can be susceptible to external damage. It is
important to ensure that the filter does not receive any external knocks during installation or operation that could damage the base, the tank or
any connections.
Always use suitable plastic connections and make ensure they are fitted with suitable supports and are not forced, or under stress.
The media must only be loaded once the filter is situated in its final position, following the instructions for “Commissioning”.
Filters like other items of plant, will need regular checks, so it is essential to leave a suitable working clearance above and around the filter.
(FIG. 3)
Correct installation of the filters:
• Place the filters in their designated position, and ensure that they are stable and the floor is perfectly flat. (FIG. 4)
• Assemble the batteries on the filters, ensuring they
are not stressed. Remember that the water tightness
of the unions is achieved with seals and gaskets, so
do not over tighten the bolts. Do not use Teflon
(PTFE) tape.
• Install adequate battery/pipe supports and adjust
their height accordingly.
• Plumb the batteries to the pump discharge pipes, the
return pipes to the pool and to the waste drain.
5.1. INSTALLATION OF THE PRESSURE GAUGES
Once you have installed the pressure gauge panel on
the flange of the filter connection, note the flexible
plastic and transparent pipes that must be connected
between the pressure gauges and the ¼” threaded
holes in the battery tees, as the illustration shows
(FIG 5).
The pressure gauge panel clearly identifies the
pressure gauge that controls the inlet and outlet
pressures. The pressure gauges indicate when
backwash of the filter is necessary. For example,
in a clean filter the entrance pressure should be
between 0.8 and 1 kg/cm
2and the exit pressure
should be between 0.4 and 0.6 kg/cm
2.
When the difference between the pressure in the
inlet pressure gauge and that in the outlet pressure
gauge is 1kg/cm
2 or higher, then it is time to
backwash the filter.
FIG.3
FIG.4
2
Product specificaties
| Merk: | Astralpool |
| Categorie: | Waterfilter |
| Model: | Olot |
Heb je hulp nodig?
Als je hulp nodig hebt met Astralpool Olot stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Waterfilter Astralpool
22 Juni 2023
22 Juni 2023
21 Juni 2023
21 Juni 2023
21 Juni 2023
20 Juni 2023
20 Juni 2023
18 Juni 2023
18 Juni 2023
18 Juni 2023
Handleiding Waterfilter
- Waterfilter Electrolux
- Waterfilter Philips
- Waterfilter Panasonic
- Waterfilter LG
- Waterfilter JBL
- Waterfilter Tefal
- Waterfilter Zanussi
- Waterfilter Avanti
- Waterfilter Bartscher
- Waterfilter Breville
- Waterfilter Brita
- Waterfilter BWT
- Waterfilter Eden
- Waterfilter Eheim
- Waterfilter Fisher And Paykel
- Waterfilter Franke
- Waterfilter GE
- Waterfilter Grohe
- Waterfilter Haier
- Waterfilter Kent
- Waterfilter Laica
- Waterfilter Midea
- Waterfilter Smeg
- Waterfilter Solac
- Waterfilter Sunbeam
- Waterfilter Terraillon
- Waterfilter Ufesa
- Waterfilter Verbatim
- Waterfilter Zodiac
- Waterfilter Jata
- Waterfilter Jura
- Waterfilter Juwel
- Waterfilter Oase
- Waterfilter Imetec
- Waterfilter Fluval
- Waterfilter Eldom
- Waterfilter Aarke
- Waterfilter Ecowater
- Waterfilter Flama
- Waterfilter FIAP
- Waterfilter Pureit
- Waterfilter Everpure
- Waterfilter Consul
- Waterfilter T.I.P.
- Waterfilter MSR
- Waterfilter Billi
- Waterfilter LifeStraw
- Waterfilter Baracuda
- Waterfilter Waterdrop
- Waterfilter Zip
- Waterfilter Waterco
- Waterfilter Aquasure
- Waterfilter ZeroWater
- Waterfilter Beemur
- Waterfilter Ionmax
- Waterfilter Puretec
- Waterfilter Tunze
- Waterfilter Aqua Medic
- Waterfilter PUR
- Waterfilter Sera
- Waterfilter Oliveri
- Waterfilter Hydor
- Waterfilter Aquael
- Waterfilter LARQ
Nieuwste handleidingen voor Waterfilter
21 November 2024
19 November 2024
19 November 2024
18 November 2024
15 November 2024
14 November 2024
28 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024