Aritech ATS1510 Handleiding

Aritech Beveiliging ATS1510

Lees hieronder de 📖 handleiding in het Nederlandse voor Aritech ATS1510 (4 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

X Y

ATS1510

Audio Module

[

Audio Module

WHAT DOES IT DO?

The ATS1510 allows event reporting including audio information used to

verify alarms by providing both live and recorded audio.

HOW DOES IT ALLOW EVENT REPORTING? (REF. TO FIG.  & )

Event reporting takes place by transmitting messages over the

telephone. After transmission of alarm information, audio information is

available for a certain period. Audio information available provides for

live and recorded audio information. Recorded audio (10) contains 15

seconds of audio information before and 15 seconds after an alarm has

occurred. Audio information is picked up by the RD3000AGC (6)

microphones and wired (8) to the ATS1510 (9) through RD3300 mixers

(11). It is advisable to use the RD3300 mixer in the following situations:

1. When the microphone cable distance is more than 50 metres; and

2. When more than one microphone per area is required.

The ATS1510 sends audio information to the control panel (12) via the

MI-bus (13). For maintenance purposes, a headphone can be connected

to check audio levels (7).

Note:

1. Recorded audio is only available for armed areas.

2. Microphones can be selected for areas using J1 to J4 on the mixer

board. For example, you can have individual connections from four

inputs to four outputs to four areas. Another possibility is to mix the

four inputs individually depending on the positions of J2, J3 and J4.

3. The tamper outputs (14) must be connected to the next available

zone of a DGP or the ATS control panel.

INPUTS AND AREAS

The 8 audio inputs can be assigned to the first 8 areas of the ATS panel.

The 8 audio inputs of a second ATS1510 (not available for

ATS2000/3000) can be assigned to areas 9 – 16 of the ATS panel.

MOUNTING LOCATION (REF. TO FIGURE  & )

The ATS1510 must be mounted inside an ATS panel housing.

Important:

1. Disconnect the mains power before opening the cabinet.

2. Disconnect AC mains plug from AC mains wall socket. OR

3. Disconnect the mains with a dedicated circuit breaker.

4. Disconnect the battery (if applicable).

MOUNTING THE UNIT (REF. TO FIGURE  & )

Mounting the ATS1510 into the control panel (ATS2000/3000/4500

series)

1. Place the clips in the square holes (4) (use metal pillars when

available).

2. Mount the ATS1510 using screws.

Mounting the ATS1510 into the control panel (ATS4000 series)

1. Remove the screws (1) and lift off the control panel PCB.

2. Place the extension pillars with the plastic rings on top of the

existing pillars (3).

3. Place the clips in the square holes (4).

4. Mount the ATS1510 using the screws and extension pillars (5).

5. Place the ATS control panel PCB back into it’s original position.

CONNECTING THE AUDIO MODULE (MI BUS)

1. Connect the flat cable (2) from the control panel (connector J20) to

the ATS1510 (connector CONN3 or CONN4).

ADVISED WIRING

To meet CE requirements the cable connected between the RD

3000AGC, the RD 3300 and the ATS1510 MUST be a screened cable.

For optimal results, use the following types of cable:

RD 3000AGC to RD 3300 Screened single twisted pair (single area

per cable run), – max. 50 m

Individually screened cable, max 800 m

RD 3300 to ATS1510 Individually screened cable, max 8 km

CONNECTING MIXERS AND MICROPHONES (REF. TO FIGURE )

No. Description Function

1. Microphone Microphone on the RD3000AGC

2. JP1 Fixed gain

3. JP2 Automatic gain control (preferred

setting)

No. Description Function

4. Tamper switch Wired separately to the mixer

board. The output (8) must be

connected to the Control Panel

(9).

5. Led Provides indication that

microphone is active and picking

up audio information.

6. RD3000AGC Microphone module

7. RD3300 audio mixer

board

Mixes signals from different

microphones to separate or to a

single output (J1, J2, J3 and J4)

8. Tamper Tamper output to control panel

input.

9. ATS Control panel ATS2000/3000/4000/4500

DESCRIPTION OF THE ATS1510 (REF. TO FIGURE )

No. Description Function

1. CONN 3/CONN 4

(System connector)

Communicates between the

ATS1510 and the main panel.

2. LED (green) Flashing indicates presence of

+12 VDC power.

3. Conn 2 Audio inputs from RD3300

mixers.

4. Conn 1 Power supply output (+ and -) to

ATS3300 mixers and external

power input (EXT and -).

5. Fuse Fuse (315 mA QB) to secure

power supply output.

6. Jumpers Test – Puts ATS1510 under test

A0, A1, A2 – MI address

selection

7. Headphone Output providing audio for

checking audio levels.

8. LED (red) Diagnostics LED indicating audio

levels during recording and

playback.

9. Int/Ext. jumper Selects int./ext. Power supply

(Factory default set to internal)

HOW TO POWER EXTERNAL DEVICES (RD3000 AND

RD3300AGC (REF TO FIGURE )

The Int/Ext. Jumper defines if the power supply output (4) for external

devices is delivered by the internal power supply (Fused, 315 mA max.)

is delivered by an external power supply (EXT, CONN1). Connect the +

from the external power supply to EXT POWER and the – to – of

CONN1.

MI ADDRESS SELECTION AND POSITIONING JUMPERS

The address of the ATS1510 on the MI-bus is determined by three

jumpers. These jumpers are placed beside the fuse holder, and are

labelled A0, A1 and A2. If only one module is used, all jumpers will be

present. For the second module, jumper A0 will be removed.

Device Jumpers

A0 A1 A2

Module 1 I I I Default I = Inserted

Module 2 R I I R = Removed

Note: A maximum of two modules can be connected. If two modules are

used, audio information for 16 areas is available.

TESTING THE AUDIO MODULE (REF. TO FIGURE )

1. Place the TEST jumper on the TEST position (6).

2. Turn the power on. The MI Bus (green LED) lights up and

remains lighted during the test mode. (The audio module will

perform a self-test.

• First a memory test will be performed for 15-20 sec.

• Then the Diagnostics LED will light up (flashing will

indicate memory test failed).

3. Connect a wire between the DIAG and input 1 from CONN 2.

After a short delay, the Diagnostics LED should go off for

approximately 0.5 sec. If not, retry.

4. If the test succeeds, do the same for inputs 2 – 8 in sequential

order.

5. Three seconds after successfully testing input 8, the

Diagnostics LED will go off and stay off.

6. Remove the TEST jumper from the TEST position. The green

LED will blink to indicate normal operation.

Product specificaties

Merk:	Aritech
Categorie:	Beveiliging
Model:	ATS1510

Heb je hulp nodig?

Als je hulp nodig hebt met Aritech ATS1510 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beveiliging Aritech

Aritech ATS1203 Handleiding

23 December 2022

Aritech AP475 SERIES Handleiding

23 December 2022

Aritech FP-FR 2000 Series Handleiding

23 December 2022

Aritech DO510 Handleiding

23 December 2022

Aritech Zerowire Handleiding

23 December 2022

Aritech ATS1510 Handleiding

23 December 2022

Aritech CS875 Handleiding

18 September 2022

Aritech CD-4401S1 Advisor Handleiding

18 September 2022

Aritech CS275 Handleiding

19 September 2022

Aritech CS575 Handleiding

18 September 2022

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging

Geemarc SOS-PRO 295 Handleiding

6 Maart 2024

Technaxx TX-106 Handleiding

4 Februari 2024

One2track Safety Angel Handleiding

16 Oktober 2023

Sygonix SY-3851632 Handleiding

16 Oktober 2023

Sygonix 1326052 Handleiding

16 Oktober 2023

Sygonix 43588A WLAN Camera Handleiding

16 Oktober 2023

Sygonix 43176S LAN Camera Handleiding

16 Oktober 2023

Sygonix SY-3181234 Handleiding

16 Oktober 2023

Sygonix Touch IP65 Handleiding

16 Oktober 2023

Sygonix 1882082 Handleiding

16 Oktober 2023