WMD Spectrum Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor WMD Spectrum (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
FT
PW FM
PWM
SAW
TRI
SINE
S/P
PLS
COARSE TUNE CONTROL
Wide range control of the VCO frequency.
FINE TUNE CONTROL
Narrow range control for ne tuning the VCO frequency.
PULSE WIDTH CONTROL
Controls the pulse width of the PULSE and CRP/ESP waveforms.
PULSE WIDTH CV ATTENUATOR
Adjusts the control voltage (CV) level or depth PWM of signals applied the
input.
SPECTRUM is a precision, saw-core VCO with eight possible waveforms (six simultaneous
outputs), an eight octave switch, LFO mode and FM mode select with attenuation. In addition to
the standard waveforms; (sine, pulse, triangle and saw), SPECTRUM features two selectable
saw/pulse hybrid waveforms and two selectable sub-octave waveforms with variable range.
Additional features include pulse width modulation with CV and attenuation, hard sync and
panel accessible 1V/OCT calibration.
PULSE WIDTH MODULATION INPUT
Apply audio or control voltage signals here to . modulate the pulse width
The eect is dependent on the relative PULSE WIDTH CONTROL and
ATTENUATOR settings.
SQUARE/ PULSE WAVE OUTPUT
PULSE wave output. Change the width/shape of the pulse with the PULSE
WIDTH control and PULSE WIDTH MODULATION input.
SINE WAVE OUTPUT
Very high purity sine wave output.
TRIANGLE WAVE OUTPUT
Symmetrical triangle out.
SAWTOOTH WAVE OUTPUT
Falling edge ramp wave - also known as a sawtooth wave.
PANEL CONTROL
LED INDICATOR
INPUT
OUTPUT
MODE SELECTOR
COLOR KEY LEGEND
CT
PW
CV
FM
SYNC
SUB
SFM
CT
FT
PW
PW
CV
FM FREQUENCY MODULATION CV ATTENUATOR
Adjusts the control voltage (CV) level or depth FM input of signals applied the .
PWM
FM FREQUENCY MODULATION INPUT
Apply audio or control voltage signals here to modulate the frequency of
the VCO. Use the FM CV ATTENUATOR to adjust the depth of modulation.
The response can be either linear or exponential - see operation modes on
page two for more information.
SCALED (1V/OCT) FM INPUT
This is the direct input for, but not limited to, controlling the VCO frequen-
cy with keyboard control voltages, midi to CV converters, sequencers and
other devices. This is an exponential CV input.
HARD SYNC INPUT
Apply pulsed or falling edge sawtooth waveforms to the SYNC input to
slave the oscillator to the applied signal frequency. The hard sync
method causes the slaved VCO to - adding harmonic reset abruptly
content to the output waveform.
SYNC
SFM
PLS
SAW/PULSE HYBRID WAVE OUTPUT
Center-Ramp-Pulse and Edge-Saw-Pulse wave outputs. Change the
width/shape of both waveforms with the PULSE WIDTH control and
PULSE WIDTH MODULATION input. Only one wave type can be selected
at a time. See operation modes on page two for details.
S/P
SINE
TRI
SAW
SUB OCTAVE OUTPUT
Outputs a sub octave sawtooth or square wave that is one or two octaves
below the main oscillator frequency. See operation modes on page two for
waveform and octave selection.
SUB
SUB
OCT
LFO
OCT
VCO
SUB
LFO 1
SUB
2
L
FM
E
CRP
WS
CAL
ESP
OCT
OCT OCTAVE SELECT SWITCHES and LEDs
Use the UP/DOWN buttons to select between a range of 8 octaves.
The three LEDs are used to indicate the currently selected octave range
in . See 3-bit binary conversion chart below.3-bit binary notation
LFO
LFO LFO MODE SELECT and LED
Push this button to set the VCO into Low Frequency Oscillator (LFO)
mode. The LFO LED is lit when LFO mode is active.
SUB
SUB
1
SUB
2
SUB OCTAVE MODE SELECT and LEDs
Hold this button down (approx 1.5s) to switch the SUB oscillator
waveform type. The SUB 1 LED will turn green for SUB SAW and blue
for SUB PULSE.
Push this button quickly to of the SUB oscillator select the octave
output. The SUB 2 LED will turn blue for one octave and green for two
octaves below the main frequency.
CRP
WS
ESP
SAW/PULSE HYBRID WAVE SELECT and LEDs
Push this button to select the hybrid waveform present at the
CRP/ESP waveform output. The respective waveform LED will be lit
when that waveform is active.
PANEL CONTROL
LED INDICATOR
INPUT
OUTPUT
MODE SELECTOR
COLOR KEY LEGEND
L
FM
E
FM INPUT MODE SELECT and LEDs
Push this button to select between Linear and Exponential response to
signal applied to the FM input and FM LEVEL control. The respective
response LED will be lit when that mode is active.
SPECTRUM OPERATION MODES
SAVING MODE STATES
Spectrum will store all mode states during power cycle intervals. Please
allow a to pass in order to insure that your minimum of 60 seconds
mode states will be retained when power is cycled o/on.
OCTAVE #
0
1
2
3
4
5
6
7
BINARY
(ACTIVE LEDs in BLUE)
BINARY to DECIMAL CONVERSION CHART
CAL 1V/OCT CALIBRATION TRIMPOT
This is the front panel access point for 1V/OCT calibration of the VCO.
SPECTRUM is calibrated at the factory to precisely track 7-8 octaves.
Therefore, it is not necessary or recommended to change the position
of the trimpot unless absolutely necessary! It is best to leave this
adjustment to a qualied technician or hobbyist.


Product specificaties

Merk: WMD
Categorie: Niet gecategoriseerd
Model: Spectrum

Heb je hulp nodig?

Als je hulp nodig hebt met WMD Spectrum stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd WMD

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd