Wagner Airless HEA Control Series 250M Handleiding

Wagner Verfspuit Airless HEA Control Series 250M

Lees hieronder de 📖 handleiding in het Nederlandse voor Wagner Airless HEA Control Series 250M (1 pagina's) in de categorie Verfspuit. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

DOING A SPRAY TEST BEFORE

STARTING YOUR PROJECT

Before taking on your project simply take a piece of cardboard and do a

couple of spray tests. This will help you to achieve the right settings on the

paint sprayer:

× After installing the correct spray tip in the holder, try different

spray directions (e.g. vertical or horizontal) as shown by the arrow

on the tip.

× Adjust the pressure on the unit. While thicker materials (e.g. wall

paint) require more pressure, thinner ones (e.g. wood stains) need

less pressure.

× If your pattern is tailing, your spray tip might be incorrect, your spray

gun filter might be clogged or the paint is not diluted enough (for

further instructions see manual).

SPRAYING TIPS FOR EVEN

COVERAGE

× Spray at a constant speed and at an even distance from the surface.

The best distance is 20 to 30 cm between the spray tip and the

surface. For ceilings and hard to reach places WAGNER oers a wide

variety of accessories like extensions, longer hoses, etc.

× Make sure you are spraying at right angles to the surface. It is

important to move your entire arm back and forth rather than just

exing your wrist, otherwise one end of the pattern will be thicker

than the other and will cause overspray.

× The spray gun should be triggered by turning it on and o with each

stroke. Do not trigger the gun during the middle of a stroke. This will

result in an uneven spray and patchy coverage.

× Overlap each stroke by about 30 % for a smooth coating.

OTHER HELPFUL TIPS

× If you accidentally sprayed too much paint on one area, dab the paint

with a cloth or kitchen roll and spray another thin coat over it.

× During a break of several hours, it is not necessary to clean the entire

unit. The gun can be simply placed in a bucket with water to prevent

the paint in the tip from drying out. You should also cover up the paint

container to prevent the paint from drying out.

For more information, please read the relevant product manual

or visit our FAQs:

go.wagner-group.com/faqs-airless

MASKING AND COVERING

× If possible, empty the room completely. Alternatively, place all the

furniture in the middle of the room and cover it with a dust sheet.

× Cover the oor with a dust sheet, painter eece or cardboard.

× Use masking tape with an integrated drop sheet to cover up large

surfaces such as windows and doors.

× In addition test that the dust sheet does not utter when you get

close to it by just using the paint sprayer to blow air.

At WAGNER we have got you covered and have put together dierent

masking kits with all you need for a wide range of painting applications.

SET-UP

× Make sure to set up the Wagner unit properly (see manual).

CHOOSING THE CORRECT SPRAY

TIP AND FILTER

× For very thick materials, e.g. wall paints, we suggest using a 515, 517

or 619 tip with white lter.

× For thin materials, such as lacquers and stains, we recommend a 311

tip with red lter.

PREPARING COATING MATERIAL

Before putting the suction hose into the material, you need to prepare it:

× Most of the units can spray material straight from the container

without diluting. However, with some more viscous materials,

diluting by 5-10 % can give a better result (e.g. for a 10 L bucket 10 %

dilution means 1 L of water).

× If working with paint, make sure that it is approximately at room

temperature. Warm materials have more viscosity and are easier to

work with. However, do not go below or above the min./max.

temperature advised by the paint supplier.

× If there are any small particles in the paint such as dry paint from the

bucket, it is helpful to lter the paint to get rid of them.

× Dilute the paint with warm water (not hot!) or solvent for solvent-

based paints in accordance with manufacturer‘s instructions.

× Stir the material thoroughly with a stirring stick for at least 2 minutes.

In the case you are working with a bigger volume, e. g. 10 L bucket, it

is better to use a drill and a mixer therefor. Stir well, and always make

sure that there are no lumps in the paint, especially at the bottom

of the bucket. Some of the heavier materials in the paint can sink to

the bottem when the bucket has been standing for a longer time on

the shelve. When not mixed well, the lumps in the paint can clog the

paint sprayer.

In case of any questions, please do not hesitate to contact us directly:

HEA SPRAYING

TIPS & TRICKS

Product specificaties

Merk:	Wagner
Categorie:	Verfspuit
Model:	Airless HEA Control Series 250M

Heb je hulp nodig?

Als je hulp nodig hebt met Wagner Airless HEA Control Series 250M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Verfspuit Wagner

Wagner FineCoat 9900 Plus Handleiding

15 November 2024

Wagner Control Pro 300 Move 18V Handleiding

7 Augustus 2024

Wagner SteamForce Speed Pro Handleiding

7 Augustus 2024

Wagner Flexio 585 Handleiding

18 December 2023

Wagner Flexio 990 Handleiding

18 December 2023

Wagner ProjectPro 213 Extra Handleiding

18 December 2023

Wagner ProSpray 3.29 Handleiding

18 December 2023

Wagner FLEXiO 995 Handleiding

13 Oktober 2023

Wagner FLEXiO 580 Handleiding

13 Oktober 2023

Wagner 2361742 Handleiding

1 Juli 2023

Handleiding Verfspuit

Nieuwste handleidingen voor Verfspuit

Ozito PXOSGK-250 Handleiding

16 November 2024

Aqua Joe AJ-MSG-TND Handleiding

16 November 2024

Worx WX020 Handleiding

5 November 2024

MSW -RPS-100 Handleiding

15 Oktober 2024

MSW -PCS-50 Handleiding

15 Oktober 2024

Abac G-542F Handleiding

27 Augustus 2024

Abac G-540F Handleiding

27 Augustus 2024

Abac G-550F Handleiding

27 Augustus 2024

Abac G-551A Handleiding

27 Augustus 2024

Einhell BT-FSS 500 Handleiding

7 Mei 2024