Wagner SprayTech FLEXiO 590 Handleiding
Wagner SprayTech
Verfspuit
FLEXiO 590
Lees hieronder de 📖 handleiding in het Nederlandse voor Wagner SprayTech FLEXiO 590 (21 pagina's) in de categorie Verfspuit. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/21
EnglishFrançaisEspañol
0113 • Form No. 0529835B
Owner’s Manual
Read this manual for complete instructions
Français (page 17) / Español (página 33)
Contents
2 Important Safety Information
4Controls and Functions
6Material Preparation
7Assembly
8 Air and Material Controls
9 Spray Pattern Adjustment
10 Proper Spraying Technique
12 Cleanup
14 Reassembly
15 Maintenance
16 Troubleshooting
49 Parts List
56 Warranty
Questions?
Call Wagner Technical Service at:
1-800-328-8251
Register your product online at:
www.wagnerspraytech.com
English
2 © Wagner Spray Tech - All Rights Reserved
Important Safety Information
Read all safety information before
operating the equipment. Save these
instructions.
Indicates a hazardous situation which,
if not avoided, could result in death or
serious injury.
To reduce the risks of re or explosion,
electrical shock and the injury to
persons, read and understand all
instructions included in this manual. Be
familiar with the controls and proper
usage of the equipment.
Grounding Instructions
This product must be grounded. In the event of an
electrical short circuit, grounding reduces the risk
of electric shock by providing an escape wire for
the electric current. This product is equipped with a
cord having a grounding wire with an appropriate
grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING - Improper installation of
the grounding plug can result in a risk
of electric shock.
If repair or replacement of the cord or plug is
necessary, do not connect the green grounding wire
to either at blade terminal. The wire with insulation
having a green outer surface with or without yellow
stripes is the grounding wire and must be connected
to the grounding pin.
Check with a qualied electrician or serviceman
if the grounding instructions are not completely
understood, or if you are in doubt as to whether the
product is properly grounded. Do not modify the
plug provided. If the plug will not t the outlet, have
the proper outlet installed by a qualied electrician.
This product is for use on a nominal 120 volt
circuit and has a grounding plug that looks like
the plug illustrated below. Make sure that the
product is connected to an outlet having the same
conguration as the plug. No adapter should be
used with this product.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
WARNING - To reduce the risk
of re or explosion:
1. Do not spray ammable or combustible
materials near an open ame, pilot lights
or sources of ignition such as hot objects,
cigarettes, motors, electrical equipment and
electrical appliances. Avoid creating sparks
from connecting and disconnecting power
cords.
2. For use with only water-based or mineral
spirit-type materials with a minimum ash point
of 21ºC (70º F) — Do not spray or clean with
liquids having a ash point of less than 21ºC
(70º F). Flash point is the temperature at which
a uid can produce enough vapor to ignite.
3. Verify that all containers and collection systems
are grounded to prevent static discharge.
4. Connect to a grounded outlet and use
grounded extension cords (electric models
only). Do not use a 3 to 2 adapter.
5. Keep spray area well ventilated. Keep a good
supply of fresh air moving through the area
to keep the air within the spray area free from
accumulation of ammable vapors.
6. Do not smoke in the spray area.
7. Do not operate light switches, engines, or
similar spark producing products in the spray
area.
8. Keep area clean and free of paint or solvent
containers, rags, and other ammable materials.
9. Know the contents of the paint and solvents
being sprayed. Read all Material Safety Data
Sheets (MSDS) and container labels provided
with the paints and solvents. Follow the paint
and solvent manufacture’s safety instructions.
10. Fire extinguisher equipment shall be present
and working.
English
© Wagner Spray Tech - All Rights Reserved 3
Important Safety Information
WARNING - To reduce the risk of
injury:
1. Always wear appropriate gloves, eye protection,
clothing and a respirator or mask when
painting. Hazardous vapors – Paints, solvents,
insecticides, and other materials can be harmful
if inhaled or come in contact with body. Vapors
can cause severe nausea, fainting or poisoning.
2. Do not operate or spray near children. Keep
children away from equipment at all times.
3. Do not overreach or stand on an unstable
support. Keep eîƒective footing and balance at
all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under
the inuence of drugs or alcohol.
6. Never aim spray gun at any part of the body.
7. Follow all appropriate local, state, and national
codes governing ventilation, re prevention,
and operation.
8. The United States Government Safety Standards
have been adopted under the Occupational
Safety and Health Act (OSHA). These standards,
particularly part 1910 of the General Standards
and part 1926 of the Construction Standards
should be consulted.
9. Use only manufacturer authorized parts. User
assumes all risks and liabilities when using parts
that do not meet the minimum specications
and safety devices of the turbine manufacturer.
10. Power cord must be connected to a grounded
circuit.
11. Do not spray outdoors on windy days.
WARNING - To reduce the risk of
electric shock:
1. Always remove turbine before cleaning.
2. Power cord must be connected to a grounded
circuit.
3. Never submerge electrical parts.
4. Never expose the equipment to rain. Store
indoors.
5. Keep electrical cord plug and spray gun trigger
free from paint and other liquids. Never hold
the cord at plug connections to support the
cord. Failure to observe may result in an
electrical shock.
Important Electrical
Information
Use only a 3-wire extension cord that has a 3-blade
grounding plug and a 3-slot receptacle that will
accept the plug on the product. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough
to carry the current your product will draw. An
undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. A 14
gauge or 12 gauge cord is recommended. If an
extension cord is to be used outdoors, it must be
marked with the sux W-A after the cord type
designation. For example, a designation of SJTW-A
would indicate that the cord would be appropriate
for outdoor use.
IMPORTANT:
Household use only. Intended
for indoor/outdoor use ONLY with materials
having ashpoint above 70ºF (21ºC).
Thank you for your purchase!
Thank you for purchasing the Wagner FLEXiO sprayer with best-in-class features
that are designed for spraying residential paint, un-thinned, indoors or out.
Only the FLEXiO sprayers have the power of the X-Boost® turbine and versatility
of the iSpray nozzle that will help you nish projects fast and professionally.
They are easy to use right out of the box and with low overspray and less
clogging you will enjoy the exibility to tackle all the painting projects on your
list. We appreciate your feedback, so please visit our website and write a review
on the FLEXiO handheld sprayer so we can continue to learn and improve our
products.
Just click on www.wagnerexio.com
Product specificaties
| Merk: | Wagner SprayTech |
| Categorie: | Verfspuit |
| Model: | FLEXiO 590 |
Heb je hulp nodig?
Als je hulp nodig hebt met Wagner SprayTech FLEXiO 590 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verfspuit Wagner SprayTech
10 Juni 2023
2 Juni 2023
20 Mei 2023
13 Mei 2023
11 Mei 2023
Handleiding Verfspuit
- Verfspuit Bort
- Verfspuit Deco
- Verfspuit Defort
- Verfspuit Easymaxx
- Verfspuit Einhell
- Verfspuit Elektra Beckum
- Verfspuit Ferm
- Verfspuit Holzmann
- Verfspuit Magnum
- Verfspuit Metabo
- Verfspuit Paintmaxx
- Verfspuit Parkside
- Verfspuit Pattfield
- Verfspuit Powerplus
- Verfspuit Silverline
- Verfspuit Wagner
- Verfspuit Westfalia
- Verfspuit Worx
- Verfspuit Jocca
- Verfspuit Ozito
- Verfspuit 3M
- Verfspuit Black And Decker
- Verfspuit Cocraft
- Verfspuit Meec Tools
- Verfspuit Aerotec
- Verfspuit Cotech
- Verfspuit Power Craft
- Verfspuit Truper
- Verfspuit Fieldmann
- Verfspuit Sun Joe
- Verfspuit Probuilder
- Verfspuit MSW
- Verfspuit Birchmeier
- Verfspuit Yato
- Verfspuit Aqua Joe
- Verfspuit Abac
- Verfspuit Meister Craft
- Verfspuit Chapin
- Verfspuit XU1
Nieuwste handleidingen voor Verfspuit
16 November 2024
16 November 2024
15 November 2024
5 November 2024
15 Oktober 2024
15 Oktober 2024
27 Augustus 2024
27 Augustus 2024
27 Augustus 2024
27 Augustus 2024