Viking E-60-BK Handleiding

Viking Intercomsysteem E-60-BK

Lees hieronder de 📖 handleiding in het Nederlandse voor Viking E-60-BK (8 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

The E-60 Series entry phones are compact,

vandal resistant, telephone line powered

speaker phones designed to provide two-way

handsfree communication. The 's compactE-60

size allows it to be mounted in a standard double

gang electrical box. The is available in fourE-60

different attractive finishes to match your door

hardware, light fixtures, etc. Replacement E-60

faceplates (PNL60) can be purchased

separately and are available in all four standard

finishes. The E-60’s blue LED continually

provides light for locating the push button in dark

locations, dims to indicate off hook and flashes

during incoming ring.

The model , ,E-60 entry phones can share a single phone line with house or small business telephones when used with a Viking C-200 C-250

C-500 or C-2000B Entry Phone controller. The entry phones can also be connected to an unused analog station port (programmed for ringE-60

down) on a phone system or connected directly to a telephone line when used with a auto dialer. TheViking model or K-1900-5 K-1900-30

E-60 features microphone and speaker volume controls, selectable auto answer for monitoring and intelligent call progress detection for automatic

hang-up when the call is completed. For outdoor installations where the unit is exposed to precipitation or condensation, the Series isE-60

available with Enhanced Weather Protection ( ). For more information on , see .EWP EWP DOD 859

PRODUCT MANUAL

Designed, Manufactured and Supported in the USA

C O M M U N I C A T I O N & S E C U R I T Y S O L U T I O N S

Entry Phones Now Mount in a Standard Double Gang Box

Features

E-60 Series

Double Gang

Entry Phones with LED

April 26, 2018

Applications

Specifications

VIKING

• Compact size: Front panel is the size of a typical double gang mid-size

wall plate

• Mounting: Flush mounts in a double gang electrical box (2.25” deep x

3.65” wide x 2.84” tall minimum) or surface mounts in a Viking model

VE-5x5 DOD 424(not included, see ) for mounting to a wall, post or

VE-GNP Gooseneck Pedestal (EWP recommended)

• Available in 4 standard faceplate finishes: Brushed Stainless Steel, Oil

Rubbed Bronze, Satin Black and Satin White

• PNL-60 faceplates: Replacement faceplates with matching screws

available in all four standard finishes

• Vandal Resistant Features: 18 gauge 304 stainless steel faceplate, 316

stainless steel push button, carbon fiber reinforced plastic speaker

screen, scratch resistant powder coating, hex drive mounting screws

• Weather Resistant Features: Mylar speaker, faceplate gasket, mic and

speaker gasket, internally sealed (IP67) push button switch, self draining

mic mount and UV stable weather resistant powder coating (excluding

E-60-SS 304 Stainless Steel faceplate)

• is designed to meet IP66 Ingress Protection Rating (see E-60-EWP DOD

859 for more information)

• Blue LED helps locate push button, indicate ringing and off hook

• Telephone line powered

• Microphone and speaker volume controls

• Programmable intelligent call progress detection for automatic hang-up on

CPC, silence, busy signal, or time out

• Selectable auto answer feature for monitoring

• Programmable VOX (mic/speaker) switching speed

• VE-LIGHT: VE-5x5 DODOptional faceplate light kit for use with the (see

859 for more information)

Power: Telephone line powered. Minimum 18V DC talk battery

voltage with a minimum loop current of 20mA. Loop current may be

boosted on low current lines with a Viking model Talk BatteryTBB-1B

Booster(see ).DOD 632

Dimensions: Faceplate: 4.875” x 4.938” x 0.17” (123.8mm x 125.4mm

x 4.3mm), Phone: 2.84” x 1.8” x 1.65” (72mm x 46mm x 42mm)

Shipping Weight: 1.2 lbs (0.55 kg)

Operating Temperature: -30° F to 150° F(-34° C to 65° C)

Humidity: Standard model: 5% to 95% non-condensing humidity,

EWP model: up to 100% humidity

Speaker Volume: Approximately 62db maximum @ 1m

Ring Voltage: 25V AC RMS minimum (for auto answer)

CPC Disconnect Time: 300ms minimum

REN: 0.8A

Connections: (2) gel-filled butt connectors

• Door or gate communication, business delivery entrances

• Use with a or to control on a single lineViking C-200 C-250 E-60

• Use with a to control 1 or 2 (expandable to 8) Viking C-500 E-60’s

and door/gate control on a single phone line

• Use with a to control 1 to 4 ’s and door/gateViking C-2000B E-60

control on a single phone line

• Provide unique front and back door chimes and paging when

used with a , and Viking SLP-1 SLP-4 C-2000B

• Residential, commercial and industrial door security

• Use with a or for automatic speedViking K-1900-5 K-1900-30

dialing on telephone lines or analog PABX/KSU station ports

• Use on any analog PABX station port with programmable

ringdown capability

E-60-BK

“Satin Black”

(fine texture satin

black powder paint)

E-60-WH

“Satin White”

(satin white

powder paint)

E-60-SS “Brushed

Stainless Steel”

(similar to brushed nickel)

Shown with optional VE-5x5

box and (not included)

E-60-BN

“Oil Rubbed Bronze”

(satin dark brown

powder paint with fine

copper metallic)

Installation

A. New Construction Flush Mounting

Step 1

Front of box should stick out approximately ½" from front surface of wall stud (this may

vary depending on the walls sheathing and siding thickness). Caution: Rough-In box

must be mounted and must stick out beyond the front surface of siding. LEVEL NOT

Step 2

To maintain a vapor barrier on outside wall applications, caulk around the box, filling any

gaps between the box and the rough opening. Apply caulk to any holes in the box around

wires, etc.

Step 3

When installing siding cut a hole just large enough for the Rough-In box opening.

Caution: Too large of a hole can cause plate misalignment and compromise the gasket

seal. Note: When mounting to 4 inch or less horizontal lap siding, a siding mounting block

can be used Contact siding installer for the correct mounting block. A sideNote:

mounting block is recommended when mounting to vinyl siding.

The E-60 is designed to be flush mounted into a standard double gang rough-in box with minimum

inside dimensions of 2.25” deep x 3.65” wide x 2.84” tall. The can also be surface mounted in aE-60

Viking model for mounting to a wall, post or Viking model gooseneck pedestal, EWPVE-5x5 VE-GNP

model recommended (not included, see ). DOD 424 WARNING: Do NOT use a typical “wet location

box” as not all styles seal properly with the faceplate.E-60

Features Overview

Rear (PCB) View of E-60

Push Button Switch: Push to

initiate call, push again to

disconnect. Solid 316 stainless

steel internally sealed per IP67.

Speaker Screen: Speaker

screen with 0.018" wide slots to

prevent punctures from

paperclips, etc.

Faceplate Material: 18 gauge

304 stainless steel. The SS model

has a #4 brushed finish, the BK,

BN and WH models have a

powder painted finish.

Speaker: Mylar speaker with

rubber gasket to maintain

water-tight seal and eliminate

water deterioration.

Mounting Screws: (4) 6-32 x

3/4" Marine grade 316 stainless

steel, flat head, 5/64" hexdrive

screws (included).

Blue Call LED: Lights steady to

help locate the button in low light,

flashes during dialing, then lights

steady when answered.

Microphone: Omni-directional

microphone with protective

water-resistant cloth.

Front View of the E-60

Faceplate Gasket: 1/8" thick

closed cell PVC to provide a

water-tight seal.

Earth Ground: To increase

surge protection, loosen the

screw labeled (as shown)

and fasten a wire with ring

terminal (included) from the

mounting screw to Earth

Ground (grounding rod,

water pipe, etc.)

Speaker Volume

Microphone Volume

Entry Phone Board:

Compact analog speaker

phone with call progress

detection for automatic

disconnect.

DIP Switches (see page 6):

1: Auto Answer Feature (on/off)

2: Dial Tone Detection (on/off)

3: Programming Switch

(normal/programming)

4: LED (on/off)

B. Old Work / Remodel Flush Mounting (Using an Allied Molded 9331 Rough-In Box)

C. Surface Mounting

D. Mounting the Faceplate

Step 1 .Make sure mounting location is free of wall studs, wires, etc.

Step 2

Place Rough-In box against siding. Trace outline of box onto siding. LEVEL Note: When mounting

to 4 inch or less horizontal lap siding, a siding mounting block can be used. Contact your siding

Installer for the correct mounting block part number. A siding mounting block is recommendedNote:

when mounting to vinyl siding.

Step 3 Cut a hole through the siding and wall sheathing just large enough for the rough-in box. Caution:

Too large of a hole can cause plate misalignment and compromise the gasket seal.

Step 4 The front surface of the Rough-In box can be mounted flush against wood siding or can be recessed

and mounted flush against wall sheathing when mounting on aluminum, steel or vinyl siding.

Step 5

When mounting to 5/8 inch thick or less wall sheathing the two attached screws with wing brackets

can be used to secure the rough-in box. When mounting to surfaces thicker than 5/8 inch, four

standard flat head dry wall screws can be used to secure the Rough-In box through its mounting

ears.

Step 6 To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps

between the box and the rough opening. Apply caulk to any holes in the box around wires, etc.

A Viking model can be used to surface mount an to a wall, post or Viking model VE-5x5 E-60 VE-

GNP Gooseneck Pedestal (EWP model recommended), see for more information on theDOD 424

VE-5x5 and VE-GNP. Drill a small wire exit hole in wall. Pull wire through and seal hole around

wire with putty or caulking. Route wire into the box, securely screw it to wall or post andVE-5x5

seal hole in box around wire with putty or caulking. Attach (2) junction box to double gang adapter

plates (included with ) to top and bottom holes of the prior to mounting the E-60 VE-5x5 E-60. Note:

Conduit may also be used when surface mounting wire, but should not enter through the top of the

VE-5x5. When routing wiring from above, a drip loop is required. WARNING: Do NOT use a typical

“wet location box” as not all styles seal properly with the faceplate.E-60

After the Rough-In box or is securely mounted, caulking between the box and rough openingVE-5x5

is completed (if required), and wires are connected, remove paper liner from face plate gasket.

While firmly holding the LED light pipe in the faceplate, carefully slide the faceplate gasket over the

back of the light pipe and press gasket to the back of the faceplate. Push the 1-1/4" 6-32 screws

through faceplate holes and small holes in gasket, the faceplate gasket should retain the screws.

Position Circuit board mounting plate over screws. Align screws with single gang box bosses and

tighten face plate until gasket is fully collapsed and the push button is protruding through the

clearance hole in the face plate. Included 1/4" thick gasket will provide an adequate seal for most

siding surfaces; however for rough surfaces (ie: brick, stucco, etc.) additional caulking may be

required.

Circuit Board

Mounting Plate

(included)

1/4" Thick Foam

Faceplate Gasket

(included)

Facplate

(included)

(4) 6-32 x 1.25" Long

5/64" Hexdrive

Flathead Screws

(included)

"Old Work" Double Gang

Rough-In Box (Allied Molded

9312 box shown, not included)

(4) Optional Dry Wall

Screws (not included)

Optional VE-5x5 Surface Mount Box with black

satin powder paint finish, not included (DOD# 424).

Optional VE-LIGHT kit can be used to illuminate the

faceplate when used with a VE-5x5 (DOD# 428).

WARNING: Do NOT use a wet location box.

2.25”

5.14”

5.22” 3.25”

3.63”

(2) Gel-Filled

Butt Co nnect o rs

(included)

Red

Gre e n

-OR-

(2) Junction Box to

Double Gang Adapter

Plates and (4) 5/64 Hex

Drive Flat Head Screws

(included with the E-60)

3.65"

Wide

Min.

2.84"

Tall Min.

*2.25"

Deep

Min. ** LED

Light Pipe

(included)

* CAUTION: Excessive wire length and/or using a rough-in box with inadequate depth can apply force to the

circuit board causing physical damage.

** Important: Push LED light pipe into faceplate hole, then place faceplate upside down on a clean flat surface

and push down on back side of plate until light pipe is fully seated and straight. WARNING: Inserting the

light pipe more than one time can cause a loose fit. 3

Product specificaties

Merk:	Viking
Categorie:	Intercomsysteem
Model:	E-60-BK
Kleur van het product:	Zwart
Gewicht:	550 g
Breedte:	125.4 mm
Diepte:	4.3 mm
Hoogte:	123.8 mm
Geluidsniveau:	62 dB
Materiaal behuizing:	Roestvrijstaal
Internationale veiligheidscode (IP):	IP67
Plaatsing:	Muur
Connectiviteitstechnologie:	Bedraad
Certificering:	CC Part 68\nFCC Part 15
Aantal knoppen:	1
Afmetingen (B x D x H):	125.4 x 4.3 x 123.8 mm
Buitenunit inbegrepen:	Ja
Gemakkelijk te installeren:	Ja
Outdoor units hoeveelheid:	1
Bedrijfstemperatuur (T-T):	-34 - 65 °C
Type product:	Uitgangsknop
Stroomtype van buitenunit:	AC/DC