Viking E-20B Handleiding

Viking Intercomsysteem E-20B

Lees hieronder de 📖 handleiding in het Nederlandse voor Viking E-20B (4 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Provide Convenient Handsfree Communication

Features

The E-10A, E-10-WHA E-20B and are telephone line

powered speaker phones that provide straightforward

two-way handsfree communication. All units function

identically, but are available in different housings to

better suit the application. When the “Call” button is

pressed, the speaker phone will come off-hook and

will remain off-hook until one of the following happens:

a CPC signal is detected, the programmed timeout

has elapsed, a busy signal is detected, or the call goes

silent, making the unit automatically disconnect.

The speaker phone can be connected directly to a

C.O. line or analog PABX/KSU station when

programmed as a ringdown circuit, or used with a

Viking Dialer. If a line or station is not available,

Viking’s DLE-200B ring down circuit can be used.

One to four speaker phones can share an existing

phone line in a house or small business when used

with a Viking or C-200, C-250, C-500, C-2000B

Controller.

For outdoor installations models E-10A-EWP,

E-10-WHA-EWP and E-20B-EWP come eqipped with

Enhanced Weather Protection (EWP). EWP products

are designed to meet IP66 standards and may feature

foam rubber gaskets and boots, sealed connections,

gel-filled butt connectors, as well as potted circuit

boards with internally sealed, field-adjustable trim pots

and DIP switches for easy on-site programming. For

more information, see . DOD 859

• Alternate action call button to place or cancel a call

• Intelligent call progress detection for automatic hang-

up on CPC, silence, busy signal, or time out

• Telephone line powered

• Weather resistant features: mylar speaker, gaskets,

internally sealed push button switch, UV stable

exterior, enamel coated PCB

• E-10A-EWP, E-10-WHA-EWP E-20B-EWP and are

designed to meet IP66 Ingress Protection Rating

• Adjustable microphone and speaker volume

• Programmable maximum call length

• Selectable auto-answer feature allows remote

monitoring

• Two way handsfree communication

• Programmable VOX (mic/speaker) switching speed

E-10A, E-10WHA Features:

- Vandal resistant, black or white powder painted,

aluminum face plate with heavy duty 316 stainless

steel call button and mounting gasket

- Flush mountable using included plastic rough-in box

part number - 259576

- Surface mount with optional ( ) VE-5x5 DOD 424

- T-10 Torx Security Screws

E-20B/E-20B-EWP Features:

- Light gray colored, impact resistant, U.V. stable,

plastic chassis

- Surface mountable only

Power: Telephone line powered (18 VDC/20mA minimum)

Dimensions: E-10A: Overall: 5” x 5” x 2.25” (127mm x 127mm

x 57.2mm), Rough-in box: 4” x 4” x 2.25” (102mm x 102mm x

57mm) 5.5” x 4.5” x 1.7” (140mm x 115mm x 43mm)E-20B:

Shipping Weights:

E-10A: 2 lbs (0.91 kg), E-20B: 1.5 lbs (.75 kg)

Operating Temperature:-30° F to 150° F (-34° C to 65° C)

Humidity - Standard Models: 5% to 95% non-condensing

Humidity - EWP Models: up to 100% condensing

Speaker Volume: Approximately 70db maximum @ 1m

Ring Voltage: 25V AC RMS minimum

CPC Disconnect Time: 300ms minimum

REN: 0.8A

Connections: (2) gel-filled butt connectors

Applications

Specifications

www.VikingElectronics.com

Information: 715-386-8861

Use as a Handsfree Speaker Phone for:

• Courtesy communication

• Delivery entrances

• Parking lots and ramps

• ATM machines

• Convention centers

• Stadiums

• Building lobbies

• Pedestrian gates

• Residences

• Businesses

DESIGNED, MANUFACTURED AND SUPPORTED IN THE USA E-10A/EWP Series

E-20B/EWP

Speaker Phones

February 9, 2021

PRODUCT

MANUAL

SECURITY & COMMUNICATION

VIKING

E-10-WHA

E-10-WHA-EWP

Flush Mount, White or Black

Powder Painted Aluminum

E-10A

E-10A-EWP

E-20B / E-20B-EWP

Surface Mount,

Light Grey UV Stable

Plastic Chassis

E-10A shown with

Viking Model

VE-GNP

Gooseneck

Pedestal

Red

(Ring)

Green (Tip)

* Gel-Filled Butt

Connectors

LED3LED1 LED2 LED4 LED5 LED6 LED7 CCCCC

C C

J11-

1 2 3

J10-

1 2 3

J9-

1 23

J8-

1 2

J7-

2 3

11 2

22 3

44 5

VIKING

©MODEL C-2000B

VIKIN G

ELECTRON I CS

HUDS ON, WI 5401 6

ADVANCED DOOR/GAT E AND

ENTRY PHONE CONTROLLER

1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

PWR 13 .8 VACEARTH GND

EN TRY PHONE 1

DOOR STRIKE 1

EN TRY PHONE 2

DOOR STRIKE 2

EN TRY PHONE 3

DOOR STRIKE 3

EN TRY PHONE 4

DOOR STRIKE 4

DOORBELL SWI TCH /

AUX. IN PUT

AUX. CONTACTOUTPUT

PH ONE LIN E

IN PU T

LIN E OUT

TO PHON ES

ANALOG STATION

IN PU T

VIKING©

DLE-200B

RES

RINGDOWN

BUSY

1 2

VIKING

Pro grammable

To ne Dia ler

MODEL: K- 1900-5

Qui ck Progra mmin g Gui de

1. Ca ll the phone connecte d to the dia ler.

2. Answe r phone . Ente r

∗

& security code .

(Fa ctory set t o 845464) Write your

security code be low:

3. Enter your spped dial numbe r & #00.

Note : For additional programming se e

K-1900-5 Technical Practice.

Viki ng Electronics , Inc.

Hud son, WI 54016

LINE IN PHO NE

Viking C-2000B 1-4 Entry Phone

Controller (not included)

** Optional Viking

K-1900-5 Dialer or

K-1900-30 Multi-

Number Dialer

(not included)

*** C.O. Line or Analog

PABX/KSU Station

(programmed for ringdown)

Viking DLE-200B

Two Way Ringdown

Circuit (not included)

To dedicated phone, unused trunk/line input of a phone system, or Viking C-1000B Doorbox Controller

SINGLE ENTRY PHONE

CONTROLLER

VIKING©MODEL C-200

PWR 13.8 VAC

AUX RELA Y

CONT ACTS

1 2 3 4 5 6 7 8 9 10

EARTH

GND

PHONE LINE

INPUT

LINE OUT

T O PHONES

T O ENT RY

PHONE

VIKING

ELECT RO NICS

HUD SO N, WI 54016

EARTH

GND C .O. LINE

INP U T OU T T O

PH O N ES ENT RY

PH O N E N. O. COM N .C.

AUX CO NT ACT S

1 2 3

Viking C-200 or C-250 Single Entry

Phone Controller (not included)

-or-

To C.O. Line or

PABX/KSU station

**** Wires from

E-10A/E-10A-EWP

E-20B/E-20B-EWP

Installation

Front View of Optional

VE-5x5 (not included)

2.25”

Condensation

Drain Hole

* 1/8" thick foam

gasket (included)

5.14”

5.22” 3.25”

Call

4.0"

Rear View of VE-5x5 (not included)

Push to Call Button

(4) 6-32 X 3/4” stainless steel, flat

head, T-10 Torx, security screws (included)

Condensation Drain Hole

5.0”

Typical

(4) 0.38” diameter (for gooseneck mounting)

(4) 0.2 x 0.43 slots for double gang box

(2) 0.2 x 0.43 slots for single gang box

(1) .74" dia

3.0” 3.3”

3.0”

2.1”

Wall Stud

Front View of Plastic

Rough-In Box (included)

Wire knock out

(2) Standard flat head dry wall

(sheet rock) screws (not included)

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC

outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.

The E-10 Series is designed to be flush mounted to the included 4” x 4” x 2” deep plastic rough in box or surface

mounted using an optional Viking model VE-5x5. Note: The E-10 Series will NOT mount to a standard double

gang box. The plastic rough in box (part # ) may be purchased separately. Go to 259576

www.vikingelectronics.com Spare Partsand click on “ ”.

A. Mounting the E-10A, E-10-WHA, E-10A-EWP or E-10-WHA-EWP

The optional Surface Mount Box is de-VE-5x5

signed to be surface mounted to a single gang

box, double gang box or gooseneck VE-GNP

pedestal (shown right). For more information

on the and , see .VE-5x5 VE-GNP DOD 424

* Note: Peel off paper

liner and adhere gasket to

the back of the faceplate,

centering it over the four

corner mounting holes.

The E-20B and are designed to be surface mounted to a single gang box (not included), a standard E-20B-EWP

4” x 4” electrical junction box (not included), or directly to a wall or flat sided post. Caution: For rough surfaces

(ie: brick, stucco, etc.) additional caulking may be required.

B. Mounting the E-20B and E-20B-EWP

3.40"

1.55"

3.40" 2.35" 3.30"

Back Panel of the

E-20B and E-20B-EWP

Side view of the

E-20B and E-20B-EWP

Mount back panel to a wall, a single

gang box or a 4”x4” junction box with

the arrow pointing up. Note: For

outdoor applications apply a bead of

caulk between back panel and wall.

Attach the cover to the

base with the two included

screws as shown.

C. Wiring

* Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum

insulation of 0.082 inches. Cut off stripped wire ends before terminating.

** Note: Talk battery must be a minimum of 28V DC when using the speaker phone with a Viking Dialer ( ) or K-1900-5 DOD# 317

K-1900-30 Multi-Number Dialer ( ). DOD 300

*** Note: TBB-1B When installing a line powered phone on a low voltage and/or low loop current phone system extension, a Viking

Talk Battery Booster may be required, see .DOD 632

**** Note: When wires are routed

from above, a “drip loop” is recom-

mended to keep water away from the

circuit board.

Caution: For rough sur-

faces (ie: brick, stucco,

etc.) additional caulking

may be required.

A. Adjusting the Speaker Volume

Programming

Step 1. ON CMove DIP switch 1 to the position (sets unit to answer incoming calls - see section ).

Step 2. ON CMove DIP switch 3 to (incoming calls automatically enter the programming mode - see section ).

Step 3. From a Touch Tone phone call the line attached to the .E-10/E-20

Step 4. E-10/E-20When the answers, 2 beeps will be heard and you will automatically enter the programming mode.

Step 5. 0000 OFF CWhen finished programming, enter “ ” to exit programming and move DIP switch 3 back to (see section ).

B. Adjusting the Microphone Volume

The SPKR VOL pot can be adjusted to increase or de-

crease the speaker volume to the level desired as shown.

ON S1

1 2 3

OFF

1 2 3

DIP Switches

(shown in default positions)

Speaker Volume

(shown in default position)

Microphone Volume

(shown in default position)

Rear View of the Speaker Phone models:

E-10 / E-20

Less (-)

More (+)

Less (-)

More (+)

* Earth

Ground

(optional)

(Spade

connector

included)

In certain noisy locations (background traffic, machinery or wind),

the microphone volume may need to be decreased. A symptom of

this is one-way talk path, in which the distant party cannot be heard

over the speaker. A pot is provided for increasing or de-MIC VOL

creasing the microphone volume. Note: If the microphone volume

is set too high or too low, one-way talk path may occur.

* Note: To increase surge protection, loosen the PCB mounting screw labeled (as

shown) and fasten a wire with spade terminal (included) from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)

C. DIP Switch Programming

Switch Position Description

1 ON Auto answer ON*

1 OFF Auto answer OFF

2 ON Dial tone detection ON*

2 OFF Dial tone detection OFF

3 ON Programming mode

3 OFF Normal operation mode*

DIP switch 1 is for turning the Auto Answer feature ON and OFF.

The E-10/E-20 is factory set to auto answer when an inbound call

is detected.

1. Auto Answer Feature (DIP Switch 1)

With DIP switch 2 in the ON position, if the detects more E-10/E-20

than 5 seconds of continued dial tone, the unit will automatically dis-

connect. If the is installed on a continuously noisy line, it E-10/E-20

may detect the noise as dial tone and automatically disconnect. If

this happens, turn the dial tone detection (DIP switch 2) OFF.

2. Dial Tone Detection (DIP Switch 2)

With DIP switch 3 in the OFF position, the E-10/E-20 is in the “Normal Operation Mode” (factory setting). By placing DIP switch

3 in the ON position, the ’s programming mode is enabled. The programming mode is used for adjusting the Call Length E-10/E-20

Time Out, Silence Time for automatic disconnect and the Talk/Listen delay (VOX switching speed). These features are set from

the factory and normally do not need adjustment. If adjustment is necessary, see sections .Programming D - I

3. Programming Mode (DIP Switch 3)

D. Accessing the Programming Mode

The E-10/E-20 can be programmed from any Touch Tone phone using a telephone line, Viking model C-200 or

C-2000A Entry Phone Controller, analog PABX/KSU station or a Viking model Line Simulator.DLE-200B

Description Select

Feature

Wait for

Beep(s)

Enter Time

Value

Wait for 2

Beeps

Call length time out (1-9 minutes), 10 = disabled (factory set to minutes) ......................................11111 = 5 0 beep 111... beep beep

Silence time out for disconnect (10-90 seconds), 10 = disabled (factory set to secs) ...................1111 = 40 00 beep 111... beep beep

Talk/listen delay (VOX switching speed) 0.1 - 0.9 seconds (factory set to 111 = 0.3 secs) ............................ 000 beep 111... beep beep

Forced hang-up command (used to exit programming and hang up) ............................................................ 0000 3 beeps 111... beep beep

E. Quick Programming Features

F. Programming Beeps

If a valid “Feature” is entered, a single beep will be heard. If an

invalid “Feature” (five or more zeros) is entered, 3 beeps will be

heard and the will hang up. If a valid “Time” is en-E-10/E-20

tered 2 beeps will be heard. If an invalid “Time” is entered, 3

beeps will be heard and you will have 20 seconds to enter the

next valid “Feature”.

G. Call Length Time Out

This feature selects the maximum length of time that calls can

be connected. Programmable in increments of 1 minute up to

a maximum of 9 minutes. Programming nothing in the time

value location will disable the call length time out. With the call

length disabled, the phone must rely on CPC, busy, E-10/E-20

silence or return dial tone to hang-up. Use the chart at the right.

* The factory default is 5 minutes.Note:

See table below

Time

Value

Call Length

Time Out

Silence

Time Out

Talk/Listen

Delay

1 1 min 10 sec .1 sec

11 2 min 20 sec .2 sec

111 3 min 30 sec .3 sec*

1111 4 min 40 sec* .4 sec

11111 5 min* 50 sec .5 sec

111111 6 min 60 sec .6 sec

1111111 7 min 70 sec .7 sec

11111111 8 min 80 sec .8 sec

111111111 9 min 90 sec .9 sec

10 or more Disabled Disabled Error 3

Product specificaties

Merk:	Viking
Categorie:	Intercomsysteem
Model:	E-20B
Kleur van het product:	Wit
Breedte:	115 mm
Diepte:	38 mm
Hoogte:	140 mm
Geluidsniveau:	70 dB
Gewicht verpakking:	750 g
Plaatsing:	Muur
Certificering:	FCC Part 68\nFCC Part 15
Aantal knoppen:	1
Gemakkelijk te installeren:	Ja
Bedrijfstemperatuur (T-T):	-34 - 65 °C