Vantage Point SATS05 Handleiding

Vantage Point Niet gecategoriseerd SATS05

Lees hieronder de 📖 handleiding in het Nederlandse voor Vantage Point SATS05 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
SoundGear
IMPORTANT CONSIDERATIONS PRIOR TO INSTALLATION
Preview all steps before beginning. Should any portion of these instructions be unclear, contact us at 800-582-9595 for assistance.
Do Not Attempt to install this Speaker Mount if you have any doubts as to its proper installation. This Speaker Mount is specifically
designed for mounting small Surround style speakers weighing 8 lbs. or less. Use of this Speaker Mount for any other purpose
unless specified by the Manufacturer is not recommended.
B - 1/4-20 x 7/8” machine screw (5)
E - 1/4-20 x 1-1/2” machine screw (5)
F - 1/4-20 x 1-1/2”
slotted screw (5)
C - #8 x 3/4” self tapping screw (5)
G - #12 x 1-3/4” self
tapping screw (10)
H - #12-14 TOGGLER
ALLIGATOR plastic anchor (2)
I - 5/32” short allen
wrench included
Mount to WallMount to Ceiling
Invert for Shelf
Mounting
Wall / Ceiling
Plate (5)
Link Set (5) assembled at factory
Speaker Post (5)
Maximum Weight Load 8 lbs.
D - 8-32 x 5/8” machine screw (5)
A - 8-32 round key hole nut (5)
REQUIRED TOOLS
™
WARRANTY INFORMATION
All Vantage Point Products Corp. products are manufactured to ensure superior quality, performance and durability for a lifetime of use . Warranty covers
the product to be free of defects in materials and workmanship under normal and reasonable use. Vantage Point Products will repair or replace, at our
option, any product which proves to be defective upon our inspection. This warranty will not apply to products that have been lost or damaged by misuse,
abuse or accident, altered or repaired in any way or by any person or firm other than specified by us, used in violation of instructions or incorrect assembly
nor used in a manner other than specified by us. This warranty is nontransferable to a new owner and may require proof of purchase. All claims must be
directly handled with Vantage Point Products Corp. by calling us at 1-800-582-9595.
Vantage Point Products Corp • P.O. Box 2485 Santa Fe Springs, CA 90670 USA
USA Tel: 1.800.582.9595 • Canada Tel: 905.607.9994 • Europe Tel: 31.72.581.6056
Web Site: www.vanptc.com • Email: cons-serv@vanptc.com
Satellite Speaker Mount Installation
Instructions For Model SATS05
Install Link Set portion of speaker mount to wall/ceiling plate. Secure the allen set
screw enough to hold assembly in place with the weight of the speaker attached.
Install speaker with speaker post attached. Secure the allen set screw enough to
hold assembly in place with the weight of the speaker attached. Adjust to desired
angle and secure.
Link Set Mounting
All Applications
tighten allen screw
using allen key
provided
(I)
Speaker Mounting
(I)
STEP 3. Installation of Link Set
(I)
TYPE 1. POST MOUNT Key Hole Design and JBL ® models.
If your speaker has a factory key hole design you will use the 8-32 x 5/8” machine screws
in combination with the 8-32 round key hole nut. Loosely pre-assemble the speaker mount
post with 8-32 screw and key hole nut (see fig.) NOTE: be sure key hole nut is installed
with knurled edge toward post. Engage the key hole nut into key hole slot as pictured. Put
tension on the assembly by gently pulling back on speaker mount post while tightening the
8-32 screw. The key hole nut will engage on housing in key hole slot.
Proceed to step (2)
If the speaker has a screwed on metal keyhole plate you may remove it and install post as shown
in TYPE 4.
(D)
(A)
keyhole speaker post
TYPE 1
TYPE 2. POST MOUNT JBL models
JBL® Speakers are supplied with a rubber bushing that is inserted into the base of the speaker as
shown. First install the Hard Rubber Bushing supplied by JBL® into the base of the JBL Speaker.
Using the 1/4”-20 x 1-1/2” slotted flat head screw, install the screw through the speaker post and
thread or push it into the hard rubber bushing.
(F)
speaker post
bushing supplied with
JBL ® speakers
speaker TYPE 2
TYPE 3. POST MOUNT Factory Installed Threaded Insert.
If your speaker has a single factory installed 8-32 threaded insert you will use the 8-32 x
5/8” machine screw for mounting the post to the speaker housing. For speakers with single
factory installed 1/4”- 20 threaded insert you will use the 1/4”- 20 x 7/8” machine screw for
mounting the post to the speaker housing. (see fig.) Once proper configuration is deter-
mined, -secure post to speaker.
(D)
(E)
speaker post
TYPE 3
STEP 1. Installation of Speaker Post to Speaker.
Supplied are parts and hardware for mounting to various manufactures speakers. You will need to select the type that best suites your applica-
tion. If the hardware provided does not fit your speaker you will need to acquire the appropriate hardware.
TYPE 4. POST MOUNT No Factory Holes, Wood Cabinet.
(Recomended use with speakers weighing 4 lbs or
less) Locate the optimum Mounting position for the post and mark through the
center of the post for drilling. NOTE: you do not want to drill or screw into the
speaker where you could possibly damage internal components. Drill a single
hole using a 3/32” drill bit. This hole should be drilled no more than 1/2” deep.
You can accomplish this by placing a piece of tape a 1/2” from the end of the drill
bit providing you with a guide. After hole is drilled, mount the post using the #8 x
3/4” self tapping screw.
Proceed to step (2)
drill 3/32” dia. x 1/2” deep hole
(C)
TYPE 4
speaker post
HOLLOW DRYWALL SURFACE - Locate best mounting location in ceiling or
wall. Using the wall plate as a template mark hole position on mounting surface (see
fig. 1)
NOTE: In wall mounting applications position mounting holes in a vertical pattern. (see
fig.) Drill holes in the drywall using a 5/16” drill bit. Once holes are drilled insert
the #12 plastic anchors into the holes making sure anchor is flush with wall or ceiling
surface (see fig. 2) With plastic anchors in place, mount the wall plates using the #12
x 1-3/4” self tapping screws (see fig. 3) Complete the installation of the remaining
wall / ceiling plates.
Proceed to step (3)
SOLID WOOD OR WOOD STUD - Using a stud finder locate the wood stud or
framing member. Using a pick or small drill bit locate the center of the wood stud, be
careful doing this as you don’t want to go any wider than the width of the wall plate
(wall plate will cover any extra holes) Using the wall plate as a template mark hole
position on mounting surface (see fig. 1) NOTE: In wall mounting applications position
mounting holes in a vertical pattern. Drill holes through the drywall and into the wood
stud using a 1/8” drill bit. These holes should be drilled no less than 1-7/8” deep (see
fig 2) You can accomplish this by placing a piece of tape a 1-7/8” from the end of the
drill bit providing you with a guide. After holes are drilled, mount the wall plate using
the #12 x 1-3/4” self tapping screws. Complete the installation of the remaining wall
/ ceiling plates. Proceed to step (3)
Mounting Hardware is supplied for 3 different surface applications. You will need to determine what style hardware will work
best with your mounting surface. NOTE: Always use CAUTION when drilling into a wall or ceiling. Make sure you are avoiding all
electrical and water lines.
drill (2)
1/8” dia.
x 1-7/8”
deep
holes
1
2
3
locate
wood stud
in ceiling
or wall
install mounting plate
using (2) #12 x 1-3/4”
screws into wood stud
(G)
(G)
drill (2)
1/8” dia. x
1-7/8” deep
holes
Insert plastic
anchor into wall.
Inse rt #1 2 x 1-3 /4”
scre w thr ough wall
plat e int o anc hor.
1
2
3
(G)
(G)
(G)
(H)
(H)
Figure 1
Figure 2
Insert plastic
anchor into concrete
wall or ceiling.
Insert #12 x 1-3/4”
screw through wall plate
into the plastic anchor.
hammer insert into
media until flush with
surface.
2
3
(G)
(G)
(G)
(H)
(H)
1
Figure 3
STEP 2. Installation of Wall / Ceiling Plate
SOLID CONCRETE OR HOLLOW BLOCK Using the wall plate as a template
mark hole position on mounting surface (see fig. 1)
NOTE: In wall mounting applications position mounting holes in a vertical pattern. (see
fig.) Drill holes in the solid concrete or hollow block using a 5/16” masonry drill bit.
Once holes are drilled insert the #12 plastic anchors into the holes making sure
anchor is flush with wall or ceiling surface (see fig. 2) With plastic anchors in place,
mount the wall plate using the #12 x 1-3/4” self tapping screws (see fig. 3) Complete
the installation of the remaining wall / ceiling plates.
Proceed to step (3)

Product specificaties

Merk: Vantage Point
Categorie: Niet gecategoriseerd
Model: SATS05

Heb je hulp nodig?

Als je hulp nodig hebt met Vantage Point SATS05 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Vantage Point

Vantage Point

Vantage Point SATS05 Handleiding

8 Juli 2023
Vantage Point

Vantage Point UL01S Handleiding

8 Juli 2023
Vantage Point

Vantage Point U70 Handleiding

6 Juli 2023
Vantage Point

Vantage Point PTC20 Handleiding

4 Juli 2023
Vantage Point

Vantage Point U50 Handleiding

3 Juli 2023
Vantage Point

Vantage Point U42 Handleiding

1 Juli 2023
Vantage Point

Vantage Point BKSPE Handleiding

1 Juli 2023
Vantage Point

Vantage Point BKSP Handleiding

30 Juni 2023
Vantage Point

Vantage Point WL01S Handleiding

30 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Topeak

Topeak Fixer 8 Handleiding

18 December 2024
Thermaltake

Thermaltake The Tower 250 Handleiding

18 December 2024
Blackburn

Blackburn Multi-Mirror Handleiding

18 December 2024
Blackburn

Blackburn Big Switch Handleiding

18 December 2024
Digi-Pas

Digi-Pas DWL-1300XY Handleiding

18 December 2024
Hayter

Hayter RANGER 48 AD Handleiding

18 December 2024
Blackburn

Blackburn Helmet Mirror Handleiding

18 December 2024
Hayter

Hayter SCARIFIER Handleiding

18 December 2024
Hayter

Hayter RANGER 53 AD 4 SPEED Handleiding

18 December 2024
Hayter

Hayter SPIRIT 41AD Handleiding

18 December 2024