Vantage Point BKSPE Handleiding

Vantage Point Niet gecategoriseerd BKSPE

Lees hieronder de 📖 handleiding in het Nederlandse voor Vantage Point BKSPE (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
rev 08/24/05
CAUTION: RECOMMENDED HARDWARE PROVIDED IS DESIGNED FOR SPEAKER WEIGHTS INDICATED. INSTALLER
MUST CONSIDER THE INTEGRITY AND DESIGN OF THE SPEAKER CABINET. SOME INSTALLATIONS MAY REQUIRE
THE INSTALLATION OF A THROUGH BOLT AND REINFORCEMENT BACKING IF SPEAKER CABINET DESIGN WILL NOT
SUPPORT SPEAKER WEIGHT.
ATTACHING SPEAKER ASSEMBLY TO EXTENSION
Install The plastic speaker plate cover (G) onto speaker plate link assembly installed on speaker
cabinet. Carefully align the link assemblies together using the threaded binder nut (I) as a guide.
Using the 5/16”-18 button head link screw (H), join the link assemblies together. Set your approxi-
mate tilt angle, being sure serrations are fully aligned at joint. Tighten the 5/16”-18 button head link
screw using the supplied 3/16” allen wrench.
G
H
ADJUSTING SPEAKER ALIGNMENT - ROTATION
You must first pull back the plastic speaker plate cover (G) to expose the link cap screws (J). You
can adjust the rotation of the speaker by loosening the 1/4”-20 socket head cap screws (J) on the
link assembly. Loosen these screws slightly using the 3/16” allen wrench (O). Adjust speaker to
desired position and re-tighten the link cap screws (J).
J
J
ROTATION
ADJUSTING SPEAKER ALIGNMENT - TILT
You can adjust the tilt of the speaker by loosening the 5/16”-18 button head link screw
(H) on the link assembly. Loosen the screw slightly using the 3/16” allen wrench (O).
CAUTION: Make sure you support the weight of the speaker as you loosen screw.
Adjust speaker to desired position and re-tighten the button head link screw (H).
TILT
H
Installation Instructions Bookshelf Series
Extended Speaker Mount-Model BKPSPE
Finished Product
PARTS LIST
Maximum weight load 25 lbs.
REQUIRED TOOLS
A
A
B
B
C
D
E
E
M
F
F
G
H
I
J
J
Assembled at Factory
A Wall Plate / Ceiling / Speaker Plate 4
B Coupler Link 4
C Extension Tube 2
D Plastic Wall Plate Cover 2
E Link 4
F Link Cap 4
G Plastic Speaker Plate Cover 2
H 5/16”-18 x 3/4” button head link screw 2
I 5/16”-18 serrated binder nut (with id. mark) 2
J 1/4”-20 x 1” socket head cap screw 16
Bagged Hardware Kit
K #14 x 2” self tapping screw 4
L #14 x 1” self tapping screw 4
M 1/4”-20 x 3/4” machine screw 4
N Toggler® Alligator anchors 4 “TOGGLER is a registered trade-
mark of Merchandise Plastics
Corp.” ALLIGATOR® ANCHOR
“Patented under US Patent num -
bers 4,181,061;4,752,170 and
5,161,296 and foreign counter
parts thereof. Other patents
pending”
K
L
O
N
SoundGear™
WARRANTY INFORMATION
All Vantage Point Products Corp. products are manufactured to ensure superior quality, performance and durability for a lifetime of
use . Warranty covers the product to be free of defects in materials and workmanship under normal and reasonable use. Vantage
Point Products will repair or replace, at our option, any product which proves to be defective upon our inspection. This warranty will
not apply to products that have been lost or damaged by misuse, abuse or accident, altered or repaired in any way or by any person
or firm other than specified by us, used in violation of instructions or incorrect assembly nor used in a manner other than specified
by us. This warranty is nontransferable to a new owner and may require proof of purchase. All claims must be directly handled with
Vantage Point Products Corp. by calling us at 1-800-582-9595.
Vantage Point Products Corp • P.O. Box 2485 Santa Fe Springs, CA 90670 USA
USA Tel: 1.800.582.9595 • Canada Tel: 905.607.9994 • Europe Tel: 31.72.581.6056
Web Site: www.vanptc.com • Email: cons-serv@vanptc.com
SOLID WOOD OR WOOD STUD - Using a stud finder locate the wood stud or framing member. Using
a pick or small drill bit locate the center of the wood stud, be careful doing this as you don’t want to go any
wider than the width of the Speaker Wall Plate (A) (wall plate will cover any extra holes) Using the wall plate
as a template mark hole position on mounting surface (see fig. 1) NOTE: In wall mounting applications
position mounting holes in a vertical pattern. Drill holes through the drywall and into the wood stud using
a 1/8” drill bit. These holes should be drilled no less than 1-7/8” deep (see fig 2) You can accomplish this
by placing a piece of tape at 1-7/8” from the end of the drill bit providing you with a guide. After holes are
drilled, mount the wall plate using the #14 x 2” self tapping screws (L).
HOLLOW DRYWALL SURFACE - Locate best mounting location in ceiling or wall. Using
the Speaker Wall Plate (A) as a template mark hole position on mounting surface (see
fig. 1) NOTE: In wall mounting applications position mounting holes in a vertical pattern. (see
fig.) Drill holes in the drywall using a 5/16” drill bit. Once holes are drilled insert the #14
TOGGLER® ALLIGATOR anchors (N) into the holes making sure anchor is flush with wall
or ceiling surface (see fig. 2) With TOGGLER® ALLIGATOR anchors in place, mount the
wall plates using the #14 x 2” self tapping screws (K) (see fig. 3).
SOLID CONCRETE OR HOLLOW BLOCK - Using the speaker wall plate (A) as a tem-
plate mark hole position on mounting surface (see fig. 1) NOTE: In wall mounting appli-
cations position mounting holes in a vertical pattern. (see fig. 3) Drill holes in the solid
concrete or hollow block using a 5/16” masonry drill bit. Once holes are drilled insert the
#14 TOGGLER® ALLIGATOR anchors (N) into the holes making sure anchor is flush
with wall or ceiling surface (see fig. 2) With TOGGLER® ALLIGATOR anchors in place,
mount the wall plate using the #14 x 2” self tapping screws (K) (see fig. 3)
16 inches
(TYPICA L)
Install mounting plate
using (2) #14 x 2”
screws into wood stud
Insert Toggler Alligator
anchor into concrete
wall or ceiling.
Insert #14 x 2” screw
through wall plate into
Alligator™ anchor.
1
2
3
Hammer insert into into
media until flush with
surface.
drill (2)
1/8”
dia.
x
1-7/8”
deep
holes
locate wood stud in
ceiling or wall
N
N
AK
K
drill (2)
5/16” dia.
x 1-7/8”
deep
holes
Insert Toggler Alligator
anchor into wall.
Insert #14 x 2” screw
through wall plate
into anchor.
1
2
3
N
K
K
K
A
N
K
A
2
SPEAKER WIRE ROUTING The design of this product allows for the concealing of the speaker
wire through the center of the extension tube.
Route the speaker wire through the access hole in the coupler link (B) feed the wire through the
center of the extension tube (C) until it exits out the opposite end. Slip wire through the center
hole on the Wall plate cover (D) and into the other link set. Speaker wire should exit through gap
between the link (E) and link cap (F). See drawing to the left for reference. Make sure when tight-
ening the link assemblies the speaker wire is not pinched or crushed.
E
J
F
D
C
BB
A
ATTACHMENT OF COUPLER LINK AND EXTENSION
Engage one half of the coupler link (B) to the extension tube (C), position assembly onto the wall/
ceiling plate (A). Move the remaining coupler link half (B) into place. Assemble using (4) 1/4”-20 x
1” socket head cap screws (J). Tighten screws using the provided 3/16” allen wrench. Make sure
coupler link (B) is fully seated onto both the wall / ceiling plate (A) and extension tube (C). This is
a good time to feed the speaker wire through assembly. Install the plastic wall / ceiling plate cover (D)
over extension tube assembly.
D
B
B
C
A
B
C
J
A
ASSEMBLY OF LINK TO EXTENSION TUBE
Install either of the links (E) onto the end of the extension tube (C). Secure link cap (F) to the link
(E) by using the 1/4”-20 x 1” link cap screws (J). Tighten the screws using the provided 3/16” allen
wrench. Make sure the link assembly is fully seated on extension tube (C).
J
F
E
C
INSTALLING SPEAKER PLATE 1/4”-20 THREADED HOLES
Hardware has been provided for speaker cabinets with factory installed 1/4”-20 threaded inserts.
Verify the thread size in your speaker cabinets prior to installation. Using the 1/4”-20 x 3/4” phillips
machine screws (M) install the speaker plate (A) to the speaker cabinet. Once speaker plate (A) is
installed, install the link (E) and link cap (F) assembly onto the speaker plate (A). Secure using the
1/4”-20 x 1” socket head cap screws. Tighten using the provided 3/16” allen wrench (O).
THREADED HOLES
MM
A
G
F
E
H
INSTALLING SPEAKER PLATE WOOD CABINETS
Locate the optimum mounting position for the speaker plate (A). Using the the speaker plate (A)
as a template, mark mounting hole location. CAUTION: Do not drill into speaker where you could
possibly damage any internal components. Drill holes using a 1/8” drill bit. Holes should be drilled
no more than 3/4” in depth. (You can accomplish this by placing a piece of tape 3/4” from the end
of the drill bit, this will provide you with a guide) Using the #14 x 1” self tapping screws (L) mount
the speaker plate (A) to the speaker cabinet. Once speaker plate (A) is installed, install the link (E)
and link cap (F) assembly onto the speaker plate (A). Secure using the 1/4”-20 x 1” socket head
cap screws. Tighten using the provided 3/16” allen wrench (O).
NO HOLES
M
A
M
G
F
E
H

Product specificaties

Merk: Vantage Point
Categorie: Niet gecategoriseerd
Model: BKSPE

Heb je hulp nodig?

Als je hulp nodig hebt met Vantage Point BKSPE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Vantage Point

Vantage Point

Vantage Point SATS05 Handleiding

8 Juli 2023
Vantage Point

Vantage Point UL01S Handleiding

8 Juli 2023
Vantage Point

Vantage Point U70 Handleiding

6 Juli 2023
Vantage Point

Vantage Point PTC20 Handleiding

4 Juli 2023
Vantage Point

Vantage Point U50 Handleiding

3 Juli 2023
Vantage Point

Vantage Point U42 Handleiding

1 Juli 2023
Vantage Point

Vantage Point BKSPE Handleiding

1 Juli 2023
Vantage Point

Vantage Point BKSP Handleiding

30 Juni 2023
Vantage Point

Vantage Point WL01S Handleiding

30 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Topeak

Topeak Fixer 8 Handleiding

18 December 2024
Thermaltake

Thermaltake The Tower 250 Handleiding

18 December 2024
Blackburn

Blackburn Multi-Mirror Handleiding

18 December 2024
Blackburn

Blackburn Big Switch Handleiding

18 December 2024
Digi-Pas

Digi-Pas DWL-1300XY Handleiding

18 December 2024
Hayter

Hayter RANGER 48 AD Handleiding

18 December 2024
Blackburn

Blackburn Helmet Mirror Handleiding

18 December 2024
Hayter

Hayter SCARIFIER Handleiding

18 December 2024
Hayter

Hayter RANGER 53 AD 4 SPEED Handleiding

18 December 2024
Hayter

Hayter SPIRIT 41AD Handleiding

18 December 2024