Unimac ACM-500 Handleiding

Unimac Compressor ACM-500

Lees hieronder de 📖 handleiding in het Nederlandse voor Unimac ACM-500 (17 pagina's) in de categorie Compressor. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/17

User Manual

[Revision 6 ].0 July 2022

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY,

PROPERTY DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE

REFERENCE. • Products covered by this manual may vary in appearance, assembly, inclusions,

specifications, description, and packaging.

The product is NOT supplied with engine oil, although traces of oil from the manufacturing process may be

present. It is essential to add adequate engine oil of the correct type to the engine before use. Failure to

add engine oil will void the product warranty.

Air Compressor – -ACM 250, ACM- 500

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• - Before Use If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• - risk Keep packaging away from children

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non slip safety footwear, hard -

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately if fuel gets on –

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build up in the tank to release -

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon Monoxide Safety-

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon poison you -monoxide a –

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

• -The equipment is not weather proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

Air Compressor – -ACM 250, ACM- 500

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before , changing adjusting

accessories or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Air Compressor Safety

Before attempting to operate this the following basic safety precautions should always be taken to reduce the risk of fire, electric shock compressor,

and personal injury. It is important to read the instruction manual to understand the application, limitations and potential hazards associated with

any tool. They are designed for the safety of yourself and others, ensuring a long and trouble -free service life from your machine.

Work Area. Workbenches should be kept tidy because cluttered benches and work areas invite accidents. Floors should be kept clean and free

from rubbish. Special care should be taken if the floor is slippery due to sawdust or wax.

Work Environment. Keep the work area well lit. Do not use compressor in areas where there is a risk of explosion or fire from combustible

materials, flammable liquids, e.g., paint, varnish, petrol etc or flammable gases and dust of an explosive nature..

Guard Against Electric Shock. Do not expose your compressor to in damp or wet locations. rain or use

Children and Pets. Children and pets should be kept out of the work area.

Use the Right Tool. Select the right tool for the job. Do not use a tool for a job for which it was not designed. Do not force a small tool to do the job

of a heavy duty tool.-

Personal Safety Clothing. Do not wear loose clothing, or anything that could get caught in moving machinery.jewellery

Hair. Long hair should be tied back or contained in a protective covering.

Eye Protection. Always use protective safety goggles or safety glasses.

Ear Protection. Ear protection is advised during periods of extended operation.

Footwear. Where there is a risk of heavy objects damaging feet or if there is a risk of slipping on wet or slippery floors suitable non-slip safety

footwear should be worn.

Secure the Work Piece. Wherever possible secure the work piece using clamps or a vice. It is safer than using your hand and leaves both hands

free to control the air tool.

Do Not Over-reach. Do not over always keep proper footing and maintain your balance-reach, .

Maintain Tools with Care. Keep cutting tools sharp and clean for better and safer performance. Follow the instructions for lubricating and changing

accessories. Check the tool power cord periodically and if damaged have it replaced by an authorized service facility. Keep handles dry, clean and

free from oil and grease. Ensure that ventilation slots are always kept clean and free from dust. Blocked ventilation slots can cause overheating and

damage to the motor.

Stay Alert. Watch what you are doing, use common sense, and do not operate the air tool when you are tired or have taken medication that causes

drowsiness, consumed alcohol or drugs.

General Warnings for Compressors

• Do not attempt to modify the compressor in any way.

• The use of any tools or accessory other than those designed for use with compressed air could result in injury to the operator.

• The output pressure of the compressor should be adjusted to the design pressure of the air tool or accessory being used.

• Always check that the output of the compressor does not exceed the maximum pressure for any attached tool or accessory.

• Repairs should only be carried out by qualified persons using original spare parts. Failure to do so may result in considerable danger to the user.

Breathable Air Warning. This compressor/pump is not equipped should not be used to supply breathing quality air for any application of air for and

for human consumption.

Overload Protection. This compressor is fitted with an overload protection device. the motor becomes too hot, a thermal protection device will If

cut the mains supply to the motor. When the motor temperature returns to normal the mains supply will be restored automatically.

Product specificaties

Merk:	Unimac
Categorie:	Compressor
Model:	ACM-500

Heb je hulp nodig?

Als je hulp nodig hebt met Unimac ACM-500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Compressor Unimac

Unimac ACM-200s Handleiding

9 April 2024

Unimac ACM-150s Handleiding

9 April 2024

Unimac ACM-160s Handleiding

9 April 2024

Unimac ACM-240s Handleiding

9 April 2024

Unimac UMVC-15S Handleiding

15 Juni 2023

Unimac ACM-1000s Handleiding

3 Juni 2023

Unimac UMC-12P Handleiding

8 Mei 2023

Unimac ACM-500s Handleiding

2 Mei 2023

Unimac ACM-400s Handleiding

2 Mei 2023

Unimac ACM-250s Handleiding

1 Mei 2023

Handleiding Compressor

Nieuwste handleidingen voor Compressor

Workzone WZK 182 Handleiding

14 November 2024

Hyundai HY3200S Handleiding

20 Oktober 2024

MSW -UVRSRI Handleiding

15 Oktober 2024

MSW -SPS-24 Handleiding

15 Oktober 2024

Einhell BT-AC 180/6 Kit Handleiding

6 September 2024

Einhell N-KS 210/8/24 Set Handleiding

6 September 2024

Anova CA30S Handleiding

5 September 2024

Anova CA50S Handleiding

5 September 2024

DeWalt D55154 Handleiding

29 Augustus 2024

DeWalt DCC2520 Handleiding

27 Augustus 2024