Tripp Lite PDUMNH20HVAT Handleiding

Tripp Lite Stekkerdoos PDUMNH20HVAT

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite PDUMNH20HVAT (72 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/72

1. Important Safety 2

Instructions

2. Installation 3

2.1 Mounting the ATS 3

2.2 Connecting the ATS 5

2.3 Networking the ATS 6

3. Features 6

4. Digital Display 8

5. Using the Digital Display 10

5.1 Navigating Display Menus 10

and Submenus

5.2 Navigating Conﬁg Menus 13

and Submenus

6 15. Conﬁguration and Operation

6.1 Automatic Transfer Switch 15

7. Service 17

8. Warranty and Product 18

Registration

Español 19

Français 37

Póññêèé 55

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

PDUMNH16HVAT

(Series Number: AG-0135)

PDUMNH30HVAT

(Series Number: AG-012F)

PDUMNH20HVAT

(Series Number: AG-0134)

PDUMNH32HVAT

(Series Number: AG-012F)

15-09-215-93338F.indb 1 9/30/2015 4:56:23 PM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation, and storage of this product.

Failure to heed these instructions and warnings may affect the

product warranty.

• The ATS provides a convenient dongle outlet, but it DOES NOT provide surge or line noise

protection for connected equipment.

• The ATS is designed for indoor use only, in a controlled environment, away from excess moisture,

temperature extremes, conductive contaminants, dust or direct sunlight.

• The ATS can only be used in a Restricted Access Location where access can only be gained by

qualified service personnel.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The ATS must be installed by a qualified technician only.

• Do not attempt to mount the ATS to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the ATS to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• Do not power on and use the ATS with one plug exposed.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the ATS to an ungrounded outlet or to extension cords or adapters that eliminate

the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Disconnect both AC input sources before servicing ATS unit.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the ATS should not draw more current than the individual

outlet’s rating.

• The total load connected to the ATS must not exceed the maximum load rating for the ATS.

• Do not attempt to modify the ATS, input plugs or power cables.

• Do not drill into or attempt to open any part of the ATS housing. There are no user-serviceable

parts inside.

• Do not attempt to use the ATS if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended. Do not use this equipment in the presence of a

flammable anesthetic mixture with air, oxygen or nitrous oxide.

1. Important Safety Instructions

15-09-215-93338F.indb 2 9/30/2015 4:56:23 PM

2.1 Mounting the ATS

The ATS supports 1U rack configurations.

Notes:

• The instructions described in this guide are for common rack and rack enclosure types and may not be

appropriate for all applications. The user must determine the fitness of hardware and procedures before

mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your

rack or rack enclosure for a solution.

• The user must determine the fitness of hardware and procedures before mounting. The PDU and included

hardware are designed for common rack and rack enclosure types and may not be appropriate for all

applications. Exact mounting configurations may vary.

• Rackmount equipment may be extremely heavy—be careful when moving or lifting equipment. Use one or more

assistants if necessary.

2. Installation

2.1.1 1U Rack Mounting

Attach the PDU to the rack by inserting four

user-supplied screws A through the PDU

mounting brackets B and into the mounting

holes of the rack rail as shown.

2.1.2 Rear Rack Rail Kit Installation

For additional stability, a front and rear rail kit can be used for rack mount installations. This kit is

included for models PDUMNH30HVAT and PDUNH32HVAT, but can also be purchased separately

for models where it is not included.

Disassemble the Bracket Sets

Note: This rail kit is only compatible with a 4-post rack or rack enclosure.

A Disassemble each bracket set by sliding

them apart.

Attach Rear Rail Segments to the Rack

B Insert two cage nuts (provided with your

rack enclosure) on each of the rear vertical

mounting rails of the rack enclosure at

your desired location.

15-09-215-93338F.indb 3 9/30/2015 4:56:24 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Stekkerdoos
Model:	PDUMNH20HVAT
Kleur van het product:	Zwart
Gewicht:	6970 g
Breedte:	430 mm
Diepte:	355.6 mm
Hoogte:	43.7 mm
Snoerlengte:	10 m
Gewicht verpakking:	7210 g
Breedte verpakking:	520.7 mm
Diepte verpakking:	520.7 mm
Hoogte verpakking:	182.9 mm
LED-indicatoren:	Stroom
Beeldscherm:	LCD
Land van herkomst:	Taiwan
Afmetingen verpakking (BxDxH):	190 x 525 x 550 mm
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-15 - 60 °C
Compatibele producten:	UL, FCC, NOM
Maat:	19 "
Hoogte, in bedrijf:	0 - 300 m
Verpakkingsinhoud:	PDUMNH20HVAT\nMounting brackets\nOwner's manual
Afmetingen (B x D x H):	44 x 356 x 430 mm
Montage:	Horizontaal
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Rackcapaciteit:	1U
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Aantal AC uitgangen:	1 AC-uitgang(en)
Nominale input voltage:	200-240 V
Stopcontacttypes:	NEMA L6-20R
Stroom (max.):	20 A
PDU types:	Monitored,Switched
Netspanning, in bedrijf:	200-240 V