Traxxas EZ-Peak Dual Handleiding

Traxxas Batterij-oplader EZ-Peak Dual

Lees hieronder de 📖 handleiding in het Nederlandse voor Traxxas EZ-Peak Dual (4 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

NiMH/LiPO DUAL CHARGER INST RUCT IONS

Covers Part #2972X

Thank you for purchasing the Traxxas EZ-Peak Dual charger.

This charger features exclusive Traxxas innovations that make

charging batteries easier and safer than ever. If you have any

questions or concerns about your charger, please contact our

customer support team for fast, friendly answers and solutions.

Contact information is at the bottom of this page.

WARNING! For best charging results and your safety, it is essential that you read and

understand these instructions, warnings, and precautions before using the charger.

Charging and discharging batteries has the potential for serious injury and damage

to property. Use care when charging and follow all instructions and cautions. A

Charge

Status

iD LogoBattery Type

Traxxas High-Current

Connector

Charge

Progress

Charge Rate

(Amps)

G G

*Note: Either charger output port can be used independently or both ports can be used

simultaneously to charge. Use the buttons corresponding with the chosen port(s) to

operate the charger.

1. Plug the charger into an AC wall outlet

and connect the battery/batteries

2. Verify the charge settings

Charging Traxxas iD NiMH Batteries

Battery type selected must match the battery type shown on the battery.

The charger will recognize the iD batteries

and show you the charge settings.

Charge Rate StartBattery Type

HKC18031-R02 180808

T R A X X A S . c o m

Traxxas, 6250 Traxxas Way, McKinney, TX 75070,

Phone: 1-888-TRAXXAS (Toll-free, US only) or 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com

3. Charging

Press and hold the Start button(s)

for 1 second. The charger will

play a tone, indicating that

charging has started. Press once

to stop. The charger will play a

tone, indicating that charging

has been canceled. The charge

progress LEDs will light as the

battery charges.

Charging

(flashing)

Charge Cycle Progress

4. Charge cycle complete

The charger will play a complete tone, followed by one or two beeps

to indicate channel 1 (left) or channel 2 (right) charging is complete.

The EZ Peak Dual will

trickle charge your NiMH

battery at up to 200mA

for 12 hours after the

charge cycle is complete.

Cycle

Complete

(solid)

A. Start/Stop

B. LiPo Charge Mode Select

C. Battery Type Select

D. Charge Rate Select

E. Charger Output Ports (Traxxas

High-Current Connector)*

F. 2S/3S Lipo Balance Ports

(pull to remove cover)

G. Charge Status LEDs

H. Charge Progress/

Charge Rate LEDs

Identifying iD Batteries LiPo battery shown, NiMH battery similar

Dual Charge Mode

Charging Traxxas iD LiPo Batteries

Fast charge

Fast charges batteries without

balancing your cells. Stops charging

when the ﬁrst cell reaches peak voltage.

Depending on the condition of the

batteries, this may reduce the charge

time by a few minutes.

Balance charge

Always balance charge your LiPo

batteries for maximum capacity,

voltage, and battery life. This is the

default setting for Traxxas iD batteries.

The EZ-Peak Dual performs a balance

charge quickly and efﬁciently.

LiPo Charging M

Storage charge

Makes it easy to charge or discharge

batteries to the proper storage

voltage. Use this mode whenever

batteries will be stored unused for

more than 7 days.

Change your LiPo charging mode if desired.

The default setting for iD LiPo batteries is Balance Charge.

Charging Traxxas iD Batteries

in High Output Mode

High Output Mode allows you to charge high capacity batteries

at a faster charge rate. Use the high output channel to charge your

5000 mAh NiMH batteries at 5 amps and your 4000 mAh and larger

LiPo batteries at a “2C” charge rate (2C is 2 times the capacity; 4000

mAh x 2 = 8000 or 8 amps). Only one Traxxas battery at a time can be

charged in High Output Mode using the output port on the right side

of the charger (the left side of the charger is disabled).

Move the switch

to High Output, and follow steps 1-4 for Traxxas iD battery charging.

Note: The 5A LED will light to indicate the charge rate setting for Traxxas

Power Cell batteries requiring a charge current of 5 amps or less.

4. Charge cycle complete

The charger will play a complete tone, followed by one or two beeps to

indicate channel 1 (left) or channel 2 (right) charging is complete.

1. Plug the charger into an AC wall outlet

and connect the battery/batteries

The charger will recognize the iD batteries

and show you the charge settings.

2. Verify the charge settings

Battery type selected must match the battery type shown on the battery.

3. Charging

Press and hold the Start button(s) for 1 second. The charger will play a

tone, indicating that charging has started. Press once to stop. The charger

will play a tone, indicating that charging has been canceled. The charge

progress LEDs will light as the battery charges.

Charging

(flashing)

Charge Cycle Progress

Cycle

Complete

(solid)

Disabled

Start

Charge Mode

(the default is

Balance) Charge RateBattery Type

Dual Charge Mode

1. Connect the main connector and the balance connector to the charger

(pull to remove balance port cover)

2. Enter Advanced Mode:

Simultaneously press and hold

the Start button and the Charge

Rate Select button for 2 seconds.

The charger will play a short tone.

Charging Traxxas Batteries without iD in Advanced Mode

Advanced Mode offers full manual control for users that have an in-depth knowledge of battery types (chemistry) and battery charging techniques.

Advanced mode also allows you to adjust the charge rate (current) for Traxxas iD batteries. If you do not understand the differences in various battery

types or what charge rates should be used, then do not use Advanced Mode. Use the Traxxas Battery iD System instead for safe, easy, and fast charging.

High Output Mode Advanced Mode (see above) can also be used while charging batteries in .

When batteries are connected for charging

that do not have Traxxas Battery iD, the red

charge rate/progress LEDs will sweep in a

scanning motion. Advanced Mode must be

used for manual battery type and charge rate

selection. The Start button will not light blue

when there is no Traxxas Battery iD present.

WARNING: DO NOT attempt to charge LiPo batteries with missing or damaged balance connectors. The EZ-Peak Dual will default to LiPo mode

charging when a balance plug connection is detected. If you fail to plug in the balance connector, or attempt to charge a LiPo battery with a damaged

or missing balance connector, you create the risk of accidentally selecting to charge a LiPo battery in NiMH mode, resulting in ﬁre and possible injury

to yourself and others. Always make sure to select the battery type that matches the connected battery. If you do not understand what this warning

means, do not attempt to use Advanced Mode on the EZ-Peak Dual. Contact Traxxas for more information.

LiPo Only

WARNING: When the charger is switched to High Output Mode, the charge rate selection begins at 5 amps and goes up to 8 amps. Make sure you

do not exceed the maximum charge rate recommended by your battery manufacturer. If you are unsure about the maximum charge rate for your

battery, then do not attempt to charge the battery in Advanced Mode. Contact Traxxas or your local hobby dealer for more information.

3b. Charging a LiPo battery or batteries

LiPo mode should be selected by default (green LEDs). If the LiPo and

NiMH LEDs alternately blink, then the balance connector is either

disconnected or damaged. Do not attempt to charge this LiPo battery.

LiPo Only

3a. Charging a NiMH battery or batteries

Press and hold the Start button(s) for 1 second. The charger will play

a tone, indicating that charging has started. Press once to stop. The

charger will play a tone, indicating that charging has been canceled.

The charge progress LEDs will light as the battery charges.

Charge cycle progresses as shown in steps 3 and 4 for iD

NiMH charging.

Select NiMH

Battery Type (Red)

Select Charge

Rate

Select Charge

Rate

Press and hold the Start button(s) for 1 second. The charger will play a

tone, indicating that charging has started. Press once to stop. The charger

will play a tone, indicating that charging has been canceled. The charge

progress LEDs will light as the battery charges.

Charge cycle progresses as shown in steps 3 and 4 for iD LiPo charging.

Select Charge

Mode

Product specificaties

Merk:	Traxxas
Categorie:	Batterij-oplader
Model:	EZ-Peak Dual
Kleur van het product:	Meerkleurig
Gewicht:	575 g
Breedte:	176 mm
Diepte:	138 mm
Hoogte:	57 mm
Soort:	Batterijlader voor binnengebruik
Ondersteund aantal accu's/batterijen:	2
Ingangsspanning:	100-240 V
Frequentie:	- Hz
Output current:	8 A
Compatibele batterij technologiën:	Lithium Polymer (LiPo), Nickel-Metal Hydride (NiMH)