System Sensor RRS-MOD Handleiding

System Sensor Detector RRS-MOD

Lees hieronder de 📖 handleiding in het Nederlandse voor System Sensor RRS-MOD (4 pagina's) in de categorie Detector. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

SPECIFICATIONS

Operating Voltage Range: 8.5 to 35 VDC

Maximum Operating Current: 25mA

Relay Contacts: 2A at 35 VDC

Operating Temperature Range: 32° to 131° F (0° to 55° C)

Operating Humidity Range: 5% to 93% non-condensing

Dimensions: 21⁄2˝ x 21⁄2˝ x 1˝

Wire connections: 18 AWG stranded, tinned, 16˝ long

RRS-MOD Reversing Relay/Synchronization Module

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

GENERAL DESCRIPTION

The RRS-MOD polarity reversing relay/synchronization module is intended

for use with 2-wire and 4-wire i3 series detectors equipped with a built-in

sounder, models 2WTA-B, 4WTA-B, 4WTAR-B, and 4WITAR-B. It is designed

to allow all the detectors in the same loop to sound when one of the detectors

goes into alarm, and to synchronize their audible output. The RRS-MOD also

allows the silencing of the detector sounders from the alarm control panel.

The RRS-MOD may be used with an alarm zone that provides coded output for

fire and continuous output for burglary. By default the RRS-MOD’s switch is

set to “off”. Therefore, the RRS-MOD will only trigger when the alarm output

is coded. In this manner, smoke detectors will only sound from the result of a

fire, and not from a burglary alarm. In this mode, the detectors will provide a

synchronized, coded output. The RRS-MOD contains a relay that is meant for

zone applications, per UL 864.

The RRS-MOD can also be set to only trigger on continuous alarm zone sig-

nals by selecting the switch to “on”. In this mode, the detectors will provide a

synchronized, coded output.

NOTICE: This manual shall be left with the owner/user of this equipment

INSTALLATION

Install in a dry indoor location. Choose a mounting location in the control

panel within reach of the provided wire leads. Use a water/isopropyl alcohol

mixture (50/50) to clean the mounting surface. Allow surface to dry and re-

move paper backing from the Velcro and catch. Stick the Velcro in the panel

and the catch on the back of the module, then mount the module inside the

control panel. Route terminals to the appropriate terminals as noted below.

WARNING

When calculating total current draw of the control panel, remember to add

current consumption (25mA) for the polarity reversal relay module (RRS-

MOD). IMPORTANT: If the fire alarm output signal is coded, set the switch on

the RRS-MOD to “OFF”. If the fire alarm output signal is continuous, set the

switch to “ON”.

WIRING

IMPORTANT: All polarities must be observed!

1. Connect the RRS-MOD module trigger wire to the fire alarm output terminals.

A. Alarm/Bell output: (Figures 1 and 2)

Connect the purple wire to the Alarm or Bell output.

B. Alarm relay, normally open contact: (Figures 3 and 4)

1. Connect one end of the alarm relay contact output to positive

auxiliary or detector power fire alarm output.

2. Connect the purple wire to the other end of the alarm relay

contact output.

2. Connect the red and black wires to the panel auxiliary or detector power

(red to positive, black to negative).

3. 2-wire models

Connect the yellow and orange wires to the panel initiating circuit (yel-

low to positive, orange to negative).

4-wire models

Connect the yellow and orange wires to the panel detector power circuit

(yellow to positive, orange to negative).

4. 2-wire models

Connect the brown and white wires to the smoke detector power supply

input (brown to positive, white to negative).

4-wire models

Connect the brown and white wires to the smoke detector power circuit

(brown to positive, white to negative).

NOTE: In an alarm condition, a wiring-fault

trouble state may also register at the panel

when the RRS-MOD is used.

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Series

D500-44-00 1 I56-2203-005

I56-2203-005

D500-44-00 2 I56-2203-005

NOTE: Please refer to Figures 5 and 6 for Ademco Vista panels and Figures 7 and 8 for DSC Power 832 panels.

S0101-01

S0102-00

S0103-01

Figure 1. 2-Wire sYsTem Triggered From aLarm/BeLL ouTPuT:

Figure 2. 4-Wire sYsTem Triggered From aLarm/BeLL ouTPuT:

Figure 3. 2-Wire sYsTem Triggered From aLarm reLaY ConTaCT:

EOL

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

–

UL LISTED

ALARM

CONTROL

PANEL

2–WIRE

INITIATING

DEVICE

CIRCUIT

PURPLE

T+

–

AUX POWER

YELLOW

IN+

ORANGE

IN–

RED

PWR+

BLACK

PWR–

BROWN

OUT+

WHITE

OUT–

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 RA-

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 RA-

–

BELL/

ALARM

CIRCUIT

(positive signal

in alarm state)

EOL

UL LISTED

ALARM

CONTROL

EOL RELAY

(SHOWN ENERGIZED)

PANEL

DETECTOR

POWER

–

AUX POWER

DETECTOR

POWER

INITIATING

DEVICE

CIRCUIT

–

BELL/ALARM

CIRCUIT

(positive signal

in alarm state)

PURPLE

T+

YELLOW

IN+

ORANGE

IN–

RED

PWR+

BLACK

PWR–

BROWN

OUT+

WHITE

OUT –

1 + IN

2 + OUT

3 - IN/OUT

4 N.O.

5 C

1 + IN

2 + OUT

3 - IN/OUT

4 N.O.

5 C

ALARM

RELAY

(NO Contact)

UL LISTED

ALARM

CONTROL

PANEL

2–WIRE

INITIATING

DEVICE

CIRCUIT

PURPLE

T+

–

AUX POWER

YELLOW

IN+

ORANGE

IN–

RED

PWR+

BLACK

PWR–

BROWN

OUT+

WHITE

OUT–

EOL

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

–

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 RA-

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 RA-

–

CAUTION

When using the RRS-MOD with model

2WTA-B, do not mix the 2WTA-B with

other model smoke detectors and dry

contact closure devices, including me-

chanical heat detectors, manual pull

stations and waterflow switches. Such

mixing can cause a direct short on the

auxiliary power terminals, damaging the

control panel’s internal circuitry and/or

damaging devices connected to the initi-

ating device circuit.

UL LISTED

ALARM

CONTROL

PANEL

2 – WIRE

SMOKE

ZONE

–

AUXILIARY

POWER

OUTPUT

YELLOW

PURPLE

T +

ORANGE

RED

BLACK

BROWN

WHITE

AUXILIARY

RELAY

470

1/2 WATT*

SYSTEM SENSOR

2WTA-B SMOKE

DETECTORS

(UP TO 16 DETECTORS

PER ZONE)

ADEMCO

CONTROL

PANEL

APPCLICABLE

CONTROLS:

5110XM

5140XM

VISTA-32FB

VISTA-100

VISTA-128FB

SYSTEM SENSOR REVERSING

RELAY/SYNCHRONIZATION MODULE (RRS-MOD)

(MOUNT INSIDE CONTROL ENCLOSURE)

NOT REQUIRED ON 5110XM

WHEN 5100XM JUMPER W3 INTACT

TAKE POWER FROM CONTROLS

AUXILIARY POWER OUTPUT ONLY

EOL

2K OHMS

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

–

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 RA-

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 RA-

–

*470 1/2 WATT RESISTOR NEEDED FOR PANEL TO RESETΩ

ALARM

CIRCUIT

(positive signal

in alarm state)

UL LISTED

ALARM

CONTROL

PANEL

INITIATING

CIRCUIT

PURPLE

T+

–

AUX POWER

2 -WIRE

YELLOW

ORANGE

RED

BLACK

BROWN

WHITE

BELL/

470

1/2 WATT*

ADEMCO

CONTROL

PANEL

APPCLICABLE

CONTROLS:

VISTA-20

VISTA-40

VISTA-50P

VISTA-32FB

VISTA-100

VISTA-128FB

SYSTEM SENSOR REVERSING

RELAY/SYNCHRONIZATION

MODULE ( RRS-MOD)

(MOUNT INSIDE CONTROL ENCLOSURE)

SYSTEM SENSOR

2WTA-B SMOKE

DETECTORS

(UP TO 16 DETECTORS

PER ZONE)

EOL

2K OHMS

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

OPTIONAL

REMOTE

ANNUNCIATOR

(RA400Z/RA100Z)

–

1 + IN

2 + OUT

3 - IN/OUT

4 N.O.

5 C

1 + IN

2 + OUT

3 - IN/OUT

4 RA+

5 C

–

*470 1/2 WATT RESISTOR NEEDED FOR PANEL TO RESETΩ

D500-44-00 3 I56-2203-005

S0104-00

Figure 4. 4-Wire sYsTem Triggered From aLarm reLaY ConTaCT:

UL LISTED

ALARM

CONTROL

PANEL

DETECTOR

POWER

–

AUX POWER

DETECTOR

POWER

INITIATING

DEVICE

CIRCUIT

–

ALARM

RELAY

(NO Contact)

PURPLE

T+

YELLOW

IN+

ORANGE

IN–

RED

PWR+

BLACK

PWR–

BROWN

OUT+

WHITE

OUT–

EOL

EOL RELAY

(SHOWN ENERGIZED)

1 + IN

2 + OUT

3 - IN/OUT

4 N.O.

5 C

1 + IN

2 + OUT

3 - IN/OUT

4 N.O.

5 C

S0105-02

Figure 5. ConneCTing 2WTa-B smoke deTeCTors To ademCo ConTroLs using rrs-mod moduLe Triggered From BeLL/aLarm CirCuiT:

S0106-02

Figure 6. ConneCTing 2WTa-B smoke deTeCTors To ademCo ConTroLs using rrs-mod moduLe Triggered From auxiLiarY reLaY:

ConneCTion diagrams WiTh ademCo VisTa PaneLs

The connection diagrams enclosed show how to connect the 2WTA-B model smoke detector to the Vista panels using the System Sensor polarity reversal relay

module (RRS-MOD). Please make sure that the smoke detectors are connected properly to the zones specified in the wiring diagrams for proper operation of the

smoke detectors.

Programming information:

• The supervisory feature for the bell cir-

cuit must be turned off. See applicable

control manual for procedure.

RRS-MOD Configuration:

• Set switch on RRS-MOD to “OFF”.

Programming information:

• Program Auxiliary relay to activate on

alarms

• Assign Auxiliary relay as an output for

zones programmed for fire alarm re-

sponse only (Types 9, 16, or 17)

RRS-MOD Configuration:

• Set switch on RRS-MOD to “ON”.

Product specificaties

Merk:	System Sensor
Categorie:	Detector
Model:	RRS-MOD
Breedte:	63 mm
Diepte:	25 mm
Hoogte:	63 mm
Gebruikershandleiding:	Ja
Aantal per verpakking:	1 stuk(s)
Soort apparaat:	Rookdetector
Compatibele producten:	System Sensor i3 Series
Type product:	Relaismodule