Supermicro SuperStorage 2029P-E1CR48L Handleiding

Supermicro Niet gecategoriseerd SuperStorage 2029P-E1CR48L

Lees hieronder de 📖 handleiding in het Nederlandse voor Supermicro SuperStorage 2029P-E1CR48L (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

Information for Lot 9 of ErP (Ecodesign)

This addendum addresses European Union (EU) Ecodesign requirements for servers and storage

products. All data and ratings within this addendum are in reference only to the Supermicro product(s) in

the manual. The below information conforms requirements laid down in Annex II of the Commission to

Regulation 2019/424.

3(1)(a): See Section 1.1 of the system manual for the product type.

3(1)(b): See the title page and preface of the system manual for the trademark and

manufacturer’s address.

3(1)(c): See the title page of the system manual for product model number(s).

3(1)(d): See the serial number on the physical system to determine the year of manufacture.

3(1)(e-j): PSU Efficiency and Power Factor Value (Table) (From 80 Plus report)

PSU Model #:PWS-1K62A- 1R

Watts: 1620

PSU Efficiency

Power Fact or

% Rated Load of

10 %

20 %

50 %

100 %

50 %

Single Output (AC-DC)

87.6 %

91.9 %

94.0 %

91.4%

0.98

System (EUT) Efficiency in Idle State Power (Table)

Representative

Configurations

Measured Idle State

Power (W)

Calculated Idle Power

Allowance (W)

High-End Performance

Configuration

312.90

679.56

Typical Configuration

N/A

Low-End Performance

Configuration

186.70

335.16

System (EUT) Efficiency in Active State Power (Table)

Representative

Configurations

Active State

Efficiency Score

(Effserver)

Minimum Active State

Efficiency for 2-Socket

Server

High-End Performance

Configuration

27.3

Typical Configuration

N/A

9.5

Low-End Performance

Configuration

18.6

3(1)(k): The operating condition class is A2.

Dry bulb temp °C

Hum idity range, non-condensing

Operating

condition

class

Allowable

range

Recom

mend ed

range

Allowable range

Recommended range

Max dew

point (°C )

Maximum

rate of

change (°

C/hr)

15 32-

18 27-

–

12 °C Dew Point (DP) and

8 % relative humidity (RH) to

17 °C DP and 80 % RH

–

9 °C DP to

15 °C and DP

60 % RH

5/20

10 35-

18 27-

–

12 C °DP and 8 % RH to

21 C and % °DP 80 RH

Same as A1

5/20

5-40

18 27-

–

12 C °DP and 8 % RH to

24 C and % °DP 85 RH

Same as A1

5/20

5-45

18 27-

–

12 C °DP and 8 % RH to

24 C and % °DP 90 RH

Same as A1

5/20

3(1)(l): The idle state power at the higher boundary temperature of the operating conditions

class is 369 W.

3(1)(m): The active state efficiency and performance is SERT Score = .327 (High End

Configuration)

3(1)(n): There are two methods by which a user can securely delete data from this system. The

user performing secure data deletion should be an IT professional.

The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility

works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe devices.

Any user may access and download this utility through following link:

https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Secure

_Data_Deletion_Utility/

Download the shell utility package and extract it to a USB flash drive, then plug the drive

into the server for which secure data deletion is necessary. Then turn the system on.

Navigate to the BIOS setup menu, then place the server system into the UEFI shell

environment. Follow the instructions in the README file to invoke the utility and

complete the deletion.

The second method is through the secure data deletion tool provided by the original

manufacturer of the hard drive. This should be used in a scenario where the shell utility

is not applicable. Each manufacturer should have the tool available on their website. If

needed, please look on the hard drive label for the name of the manufacturer and model

information.

3(1)(o): List of recommended combinations of blade servers with chassis: N/A.

3(1)(p): List of all current SKUs within this product family: -E1CR48H, 2029P-E1CR48L. 2029P

3(3)(a): There is no use of cobalt in batteries in this product.

The indicative weight range of neodymium in the HDD is 0.0 if manufactured by Western

Digital, and is between 5-25 grams if manufactured by Seagate.

3(3)(b): Please see the disassembly instructions on the next page.

Product specificaties

Merk:	Supermicro
Categorie:	Niet gecategoriseerd
Model:	SuperStorage 2029P-E1CR48L
Gewicht:	29500 g
Breedte:	437 mm
Diepte:	684 mm
Hoogte:	89 mm
Aan/uitschakelaar:	Ja
Processorfamilie:	Intel® Xeon® Scalable
Ethernet LAN:	Ja
Aantal USB 2.0-poorten:	1
VGA (D-Sub)poort(en):	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Duurzaamheidscertificaten:	RoHS
Type processor:	Nee
Temperatuur bij opslag:	-40 - 60 °C
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A:	2
Processor socket:	LGA 3647 (Socket P)
Maximum intern geheugen:	6000 GB
On-board graphics adapter model:	Aspeed AST2500
Luchtvochtigheid bij opslag:	8 - 90 procent
Reset button:	Ja
Type behuizing:	Rack (2U)
80 PLUS certificatie:	80 PLUS Titanium
Redundante voeding:	Ja
ECC:	Ja
Veiligheid:	5 - 95
Chipset moederbord:	Intel® C621
PCI Express x16 (Gen 3.x) slots:	2
Ondersteunde opslagstationinterfaces:	Serial ATA III, Serial Attached SCSI (SAS)
Seriële poort(en):	1
Soorten RAID:	0, 1,5, 6,10, 50, 60
PCI Express x8 (Gen 3.x) slots:	1
Aantal hoofdvoedingen:	2
Geheugenbus:	50 Bit
Aantal SATA III connectors:	8
Aantal ondersteunde processoren:	2
Aantal DIMM sloten:	24
Ondersteunende RDIMM klok snelheden:	2133,2400,2666,2933 MHz
Opslagschijf afmetingen ondersteund:	2.5 "
Ondersteunde geheugen types:	DDR4-SDRAM
Hot-swap HDD bays:	Ja
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	10 - 35 °C
Ventilator diameter:	- mm
BIOS type:	UEFI AMI
IPMI LAN (RJ-45) port:	Ja