Sunpak 5200D Handleiding

Sunpak Statief 5200D

Lees hieronder de 📖 handleiding in het Nederlandse voor Sunpak 5200D (2 pagina's) in de categorie Statief. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Operating Instructions

Congratulations on the purchase of your new

SUNPAK tripod. Your tripod has been designed

to be a sturdy, rugged, and dependable product and

will provide you with many years of reliable service.

Please spend a few moments reviewing these

instructions, so that you can take full advantage

of your tripod’s features and capabilities.

SUNPAK ONE YEAR LIMITED WARRANTY

This SUNPAK product has been carefully manufactured, accu-

rately adjusted, inspected and thoroughly tested before shipment

to assure you of the highest quality.

Should this SUNPAK product require service, we will repair or

replace, at our option, any part or the product itself, which our

examination shows to be defective in material or workmanship.

This warranty does not apply to wear and tear associated with

the normal use of the product. This warranty is non-transferable.

Repairs will be made to the product at no charge, under the

terms of the warranty as stated above, only when accompanied

by a dated and itemized bill of sale and nominal handling charge.

Be certain to follow all assembly and/or operating instructions

with this product. This warranty is not valid if the product has

been misused or damaged in any way that is beyond our control

or through normal wear and tear associated with use. This war-

ranty applies only to the product and we are not responsible in

any way for losses, damages or any inconvenience caused by

equipment failure.

Some states do not allow the exclusion or limitation of conse-

quential damages, so the above limitation or exclusion may not

apply to you. This warranty gives you specific legal rights and

you may have other rights which may vary from state to state.

Should service be required, the product should be carefully

packed (in the original packaging if possible ) and sent, prepaid

and insured, along with a check or money order for $9.95

(shipping and handling), to the address listed below. A note

briefly describing the nature of the defect should also be en-

closed to expedite handling.

Proof of purchase and payment for shipping and handling

must be included for warranty repairs.

OWNER’S RECORD

Please complete this section and retain with your original bill of

sale for your records.

Purchase Date ________________________________________

Model _______________________________________________

Dealer’s Name ________________________________________

Address _____________________________________________

City ________________________________________________

State ___________________ Zip Code ____________________

ToCAD America Inc.

Sunpak Tripod Division

53 Green Pond Road

Rockaway, NJ 07866

973-627-9600

www.tocad.com

Precautions

 Insure that all levers, handles, knobs and

leg locks are properly tightened, and that all

three legs are fully angled opened before

use.

 Do not mount any camera directly onto the

head mount screw located on the top of the

tripod’s center column. The screw may be

longer than the tripod socket in your

camera, and could possibly cause damage.

 Do not carry or transport the tripod with the

camera equipment attached (as example

but not limited to: over your shoulder or

cradled in your arms).

 Do not Oil or Grease any part of the tripod.

 Do not use any solvents or thinners to clean

your tripod. Use mild detergent and wipe dry

with a soft, lint-free cloth only.

 Do not store or expose your tripod to

excessive heat or cold or use close to any

flame or fire.

 Do not exceed the load limit for this product.

Cat. no. 620-520D

Opening and Closing the Tripod

Your Sunpak 5200D tripod is equipped with metal

Center Leg Braces for maximum stability and

strength.

Extend the leg sections to the desired length and

secure each section using the Leg Locks. Draw

each leg outward until all three braces are fully

extended and gently press down on any brace until

it stops.

When closing the tripod, gently push up on any Leg

Brace.

Height Adjustments

Your Sunpak 5200D tripod is equipped with a

Geared Center Column and Elevator Crank Assem-

bly for precise height adjustments.

To raise or lower the Center Column, loosen the

Center Column Lock Knob (1). Turn the Elevator

Crank Assembly knob clockwise until you reach the

desired height. Retighten the Center Column Lock

Knob to secure.

Note: Never release your camera until the Center

Column Lock Knob is securely retightened.

Specifications Folded Length 20.5 in. (52 cm)

Maximum Height 52 in. (132 cm)

Minimum Height 19 in. (48.2cm)

Weight 1.8 lbs. (.8 kg)

Load Capacity 3.3 lbs. (1.5 kg)

Quick Release Plate

Move the Quick Release Locking Lever outward

and remove the Quick Release Plate by lifting

upward. The plate has a threaded ¼” - 20 camera

mounting screw for camera attachment.

Position the Quick Release Plate so that the

camera mounting screw aligns with the matching

receptacle on your camera or camcorder and

attach, using the camera mounting screw. Move

and hold open the Quick

Release Lock Lever and

with the camera tilted

slightly down, slide the

Quick Release Plate back

into position. After doing

so, secure the Quick

Release Plate using the

Quick Release Locking

Lever by pressing firmly

until it stops.

Using the 3-way Panhead

For panning and tilting, loosen the Pan and Tilt

Handle, by turning the handle counterclockwise.

Tilt the Panhead as desired and retighten by

turning clockwise or leave loose for panning.

To change the camera format from horizontal to

vertical, loosen the Vertical Tilt Lock Knob (1) and

rotate the camera platform (2) 90 degrees to the left

to its vertical position. Retighten the Vertical Tilt

Lock Knob.

Extending the 5200D Legs

Each leg of the Sunpak 5200D has flip leg lock lev-

ers and each segment may be withdrawn as

needed. This permits setting your equipment at a

comfortable height and can be very useful when

positioning your tripod on uneven terrain.

To deploy any leg extension, flip open the leg lock

lever and gently pull on the leg segment to the de-

sired length. To secure in position, press the leg

lock lever until it is locked. Not properly securing a

leg lock may cause the tripod leg to retract

unexpectedly and result in damage to your camera

and tripod).

Tripod Components

1. Vertical Tilt Lock Knob

2. Pan and Tilt Handle

3. 3-Way Panhead with Bubble Level

4. Quick Release Plate with Locking Lever

5. Center Column Lock Knob

6. Elevator Crank Assembly

7. Geared Center Column

8. Leg Brace

9. Flip Leg Lock

10. Rubber Foot

10 Locked Unlocked

Product specificaties

Merk:	Sunpak
Categorie:	Statief
Model:	5200D
Kleur van het product:	Zwart
Gewicht:	800 g
Hoogte (min):	482 mm
Hoogte (max):	1320 mm
Maximale gewichtscapaciteit:	1.5 kg
Materiaal:	Aluminium
Bedoeld voor:	Digitaal/filmcamera
Lengte wanneer opgevouwen:	520 mm
Aantal benen/poten:	3 poot/poten
Aantal pootsecties:	3
Toepasbaarheid:	Universeel
Type beenvergrendeling:	Omklapvergrendeling