Sunding SD-782 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Sunding SD-782 (1 pagina's) in de categorie Fietslamp. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
SD-782Bicycle Recharge Taillight Instructios
Functions
Parts List
Parts INFO
Battery Charging
Open the rubber charging cover, insert the plug into the socket,
Port Micro USB, Charging voltage 4.5V口 口
Installation
Install on the backpack:
Operating Instruction
TROUBLESHOOTING
Error
Causes & Troubleshooting
Turn off automatically after
the flash light for 1 minute
The battery power is low and
needs to be charged
There is abnormal sound
when shaking
The sensor scroll switch with
automatic function makes a
sound,It is normal.
Long Open
State
ON/OFF ON/OFFON/OFF
ON/OFF
MODE Button
MODE Button
MODE Button
MODE Button
Water
Flash
Chasing
Flash
Breathing
Flash
Warning
Flash
Exposure
Flash
Automatic
State OFF State
MODE Button
- 5 Flash Modes: Water Flash/Chasing Flash/Breathing Flash/
Warning Flash/Exposure Flash
- Long Flash Function
- Automatic Flash Function
-R echargeable Battery
-Waterproof Design
The red light next to the button lights during charging, and the red light goes out
after about 4 hours. When the green light is on, the battery is fully charged and the
charging is complete.
After the battery is fully charged, different modes can work continuously: Water
flash 12 hours, Chasing flash 15 hours, Breathing flash 7 hours, Warning flash 8
hours, Exposure flash 51 hours, when the battery power is low, the LED light
stops flashing and automatically enters the shutdown state.
Install on seatpost and handlebar:
Use the back clip on the host back to clip the host to the backpack(as shown below)
Push the buckle belt into the back clip of the host (as shown below), pay attention
to the direction of the buckle, with a sloped upward.
Aach the installed buckle belt of the host to the seatpost
or handlebar:
Attach the buckle belt close to the seatpost or handlebar, tighten the buckle belt to
hang the hook into the round hole, and pin the end of the buckle belt into the
bottom of the hook ( As shown below)
Long Open Funcon:
Press ON/OFF key, the tail light will enter the long open function state, and the
LED light will be flashing in the mode of water flas.
In the long open function state, press the MODE key to switch to chasing flash,
breathing flash, warning flash, and exposure flash mode in turn.
Automac Flash Funcon:
In the long open function state, press the ON/OFF button to flash the LED light
fully twice before entering the automatic flashing function state.
In the automatic flashing state, when the tail light is in a dim light environment,
when riding or the taillight is shaken, the LED light starts to blink, and after 20
seconds, if the taillight is at rest or in a bright light environment, the LED light
stops flashing.
In the automatic flashing state, press the MODE key to switch to chasing flash,
breathing flash, warning flash, and exposure flash mode in turn.
Flash Off:
In the automatic flashing state, press the ON/OFF
button to flash the LED light fully once, Flash off.
MODE Button
MODE Button
MODE Button
MODE Button
Water
Flash
Chasing
Flash
Breathing
Flash
Warning
Flash
Exposure
Flash
MODE Button
Rubber Charg ing Cover
Back Clip
MODE B uon
Buckle Hook
ON/O FF
Sili con e Buckl e
Rubber Strap Host
Note the direcon of buckle


Product specificaties

Merk: Sunding
Categorie: Fietslamp
Model: SD-782

Heb je hulp nodig?

Als je hulp nodig hebt met Sunding SD-782 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden