Sunding SD-581G Handleiding

Sunding Niet gecategoriseerd SD-581G

Lees hieronder de 📖 handleiding in het Nederlandse voor Sunding SD-581G (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
CLK Mode(12H/24H)
Mounting Shoe
While the default Maintenance Alert digit
200 RIGHTkm/m is flashing, Press the button
to choose km/m. Press the 200/400/600/800
left button to confirm and enter into Clock mode. (when the
ODO the Maintenance Alert digit you set, the will
appear on the screen to alert the rider, press the RIGHT
button seconds to cancel it.)3
Remove the battery cover from the bottom of the computer by using
a flat blade screwdriver, install battery with the positive (+) pole
facing the battery cover and replace the cover. Should the LCD
show irregular figures, take out the battery and reinstall it.
Attach the sensor transmitter to either front fork using the supplied
cable ties. Fit the magnet to a spoke using the diagram above as a
guide. Position the sensor & magnet as shown above. Take care to
align the magnet to either arrow on the sensor with 3~5 mm gap in
between.
Attach the mounting shoe with the cable ties
to the handlebars as shown in the diagram.
Attach the computer to the mounting shoe by sliding the unit until it
snaps firmly into position. To remove, press down on the release
catch, and remove the computer.
To check for proper speed function and sensor alignment, spin the
front wheel with the computer in speed mode. Adjust the position of
sensor and magnet if there is on or weak signal.
Computer
Wheel Size Input
‘ ’ appears on the screed when the battery has been installed, 2060
with one figure flashing enter the wheel circumference using the
formula below.
In the example above you would enter . Press the 2198 RIGHT
button to advance the digits as needed and the button to LEFT
confirm and advance. (The circumference ranges 0mm~9999mm),
press the button to enter mode.LEFT KM/M
Setting(km/h)/(m/h)
Press the button to choose or .RIGHT km/h m/h
Press the button to enter mode.LEFT CLOCK
Setting Maintenance alert
In mode, press the button for seconds to set the ODO LEFT 2 ODO
value. The initial value is . when one figure flashes, press the 0000.0
RIGHT button to adjust it, and the LEFT button to confirm and start
to set the next figure. NOTE: Before re-installing the
battery, take a note of your mileage and then re-enter
the value once the battery is replaced.
In CLOCK Mode, press the LEFT button for seconds 3
to enter 12/24H selection. Press once more to swap
between 12/24 hours. Press the RIGHT button to enter
the Hour mode, when the figure indicating HOUR
starts to flash, press the LEFT button to adjust it. Continue to press
the RIGHT button to enter the Minute mode, when the figure indicating
MINUTE starts to flash, press the button to adjust. Press the LEFT
RIGHT button to confirm & press the RIGHT button again to switch to
ODO mode.
Setting the Last value of Odometer
Sensor Wiring
Computer Battery Installation
-SPD CURRENT SPEED
-ODO ODOMETER (0.001~99999km/m)
-DST TRIP DISTANCE
-MXS MAXIMUM SPEED
-AVS AVERAGE SPEED
-TM ELAPSED TIME
-CLK CLOCK (12H/24H)
-SCAN
- “-” “+” COMPARATOR
-SETTING SPEED SCALE ,(km/h m/h)
-SETTING TYRE CIRCUMFERENCE (0mm~9999mm)
-SETTING THE LAST VALUE OF ODOMETER /ODO
-MAINTENANCE ALERT
-FREEZE FRAME MEMORY
-BACK LIGHT
-AUTO ON OFF /
16 function cycle computer
Instruction Manual
FUNCTIONS
Speedometer Sensor
Route the sensor wire up the fork blade,
using the cable ties to secure it. Make
sure it does not hinder the movement
of the front wheel.
SD-581G
≤3mm
TYRE DIAMETER IN MM
× 3.14=CIRCUMFERENCE
EG: - Wheel 686mm diameter
Calculate 686×3.14=2154.04
Enter first 4 digits ‘2154’
NOOFF
Malfunctions and Problems
Button Instruction
Freeze Frame Memory
Sleep Mode
Trip Time
Average Speed
Maximum Speed (MXS)
Reset of Mileage Parameter
In mode, press and hold both the and buttons ODO RIGHT LEFT
simultaneously for seconds to clear the tyre circumference and 3
(km/m) settings. The clock settings will remain unchanged.
Speedometer
In mode, the total distance is indicated ODO
on-screen.
The mileage range is ~ km(m). The 0.001 99999
display will return to when the value exceeds its 0
maximum limit, press the button to enter mode.RIGHT DST
Speed is shown at all times on-screen, its maximum reading is
99.9 0.1km/h(m/h), and is accurate to +/- km/h (m/h).
Speed Comparator
During riding, ‘ ’ and ‘ ’ indicates the current speed is higher or lower + -
than the average speed (AVS).
Odometer
Trip Distance (DST)
In mode, the distance for one trip is indicated DST
on the bottom line. ranges from km(m).DST 0~9999
When the value exceed the range limit, it resets to 0
automatically. Both the time and the distance records
will be cleared when the time of one trip exceed the range limits.
Press the button for seconds to clear the records of , LEFT 5 DST
MXS AVS TM, and .
Press the button to enter mode.RIGHT MXS
In mode, maximum speed is indicated on the MXS
bottom line. Press the button for seconds to LEFT 5
clear the records of , , MXS DST AVS TM and .
In AVS mode, average speed is indicated on the
bottom line. Press the button for seconds to LEFT 5
clear the records of AVS DST MXS TM, , and .
Press the right button to enter mode.TM
In mode, trip time is indicated on the bottom line. TM
TM ranges from to , and will be reset to when the 0:00:00 99:59:59 0
value exceed the limit.
Press the button for seconds to clear the LEFT 5
records of , , and TM DST MXS AVS.
Press the button to enter mode.RIGHT SCAN
Scan
In mode , , , SCAN DST MXS AVS TM and modes are
indicated in turn every seconds.4
Press the button to enter Mode.RIGHT CLOCK
If no signal has been received for seconds, the computer will 300
enter into Sleep Mode, the value remains stored. It will turn CLK
back to the previous mode with all the data collected when the signal
is received again or any button is pressed.
Press the button at any time to enter into freeze frame LEFT
memory mode. Flashing data will appear on the screen. Press TM
the button to view the records of , , RIGHT DST MXS AVS TM. and
Press the button to choose any mode below : , , RIGHT ODO DST
MXS AVS TM SCAN DST MXS AVS TM CLOCK, , , ( , , & ) and . It is
not necessary to press the button except to select the Freeze LEFT
frame Memory mode.
In Freeze Frame Memory mode, press the button, data will RIGHT
be displayed, press button once more to return back to other LEFT
modes.
Malfunction
Problems
No speedometer
Incorrect magnet / sensor alignment.
Inaccurate value is
indicated
Improper input, such as wheel
circumference.
Slow display response
Temperature exceeds operating limits
(0°C~55°C).
Black display
Temperature too high, or placed in direct
sunlight for too long. Let the unit cool
down.
Weak display
Poor battery contact or dead battery.
Display shows irregular
figures
Take out battery and re-install after 10
seconds.
Accessories
Sensor Transmitter
Mounting Shoe
Cable Ties
Wheel Magnet
Back Light
The back light function is switched on or off when you press any button
during 18:00~06:00.Itwill not work at any other time.
CR2032 Battery

Product specificaties

Merk: Sunding
Categorie: Niet gecategoriseerd
Model: SD-581G

Heb je hulp nodig?

Als je hulp nodig hebt met Sunding SD-581G stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Sunding

Sunding

Sunding SD-581C Handleiding

30 Januari 2025
Sunding

Sunding JOY-651 Handleiding

30 Januari 2025
Sunding

Sunding SD-589 Handleiding

30 Januari 2025
Sunding

Sunding SD-536B Handleiding

30 Januari 2025
Sunding

Sunding SD-579 Handleiding

29 Januari 2025
Sunding

Sunding SD-590C Handleiding

29 Januari 2025
Sunding

Sunding SD-581G Handleiding

29 Januari 2025
Sunding

Sunding JOY-583C Handleiding

17 November 2024
Sunding

Sunding SD-521 Handleiding

7 Juli 2023
Sunding

Sunding SD-518 Handleiding

2 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Sonifex

Sonifex DHY-04S Handleiding

30 Januari 2025
Wimberley

Wimberley AP-612 Handleiding

30 Januari 2025
Sonifex

Sonifex Redbox RB-PD2 Handleiding

30 Januari 2025
SmallRig

SmallRig FilMov 67mm Handleiding

30 Januari 2025
Scanstrut

Scanstrut RLS-508-404 Handleiding

30 Januari 2025
Scanstrut

Scanstrut PTM-R2-SL Handleiding

30 Januari 2025
JLCooper

JLCooper SloMo Elite-C Handleiding

30 Januari 2025
Scanstrut

Scanstrut SPT1001 Handleiding

30 Januari 2025
SmallRig

SmallRig FilMov 17mm Handleiding

30 Januari 2025
Scanstrut

Scanstrut RL-RM Handleiding

30 Januari 2025