Sun Joe 24V-HCSWP-CT Handleiding

Sun Joe Zaagmachine 24V-HCSWP-CT

Lees hieronder de 📖 handleiding in het Nederlandse voor Sun Joe 24V-HCSWP-CT (76 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/76

Original instructions.

A Division of Snow Joe, LLC Model 24V-HCSWP-CT Form No. SJ-24V-HCSWP-CT-880E-M

OPERATOR’S MANUAL

CORDLESS TELESCOPING

POLE + PRUNING SAW – TOOL ONLY

24V MAX* | 250W | 5" BAR + CHAIN LENGTH

*Initial no-load voltage, when fully charged, peaks at 24 volts;

nominal voltage under typical load is 21.6 volts.

SAVE THESE INSTRUCTIONS

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the power tool, basic safety

precautions should always be followed to reduce the risk of

re, electric shock, and personal injury. These include:

1. Keep work area clean and well-lit – Cluttered, dark

areas invite accidents. Always inspect the area where the

pole + pruning saw is to be used.

2. Avoid dangerous environments – Do not use the power

tool in rain, in damp or wet locations, or in bad weather,

especially when there is a risk of lighting. This decreases

the risk of being struck by lighting. Do not operate the

power tool in gaseous or explosive atmospheres or use

the power tool near ammable or combustible liquids.

Motors in these tools may spark, and the sparks might

ignite fumes.

3. Know your product – Know how to start and stop the

machine. Be thoroughly familiar with the controls.

4. Keep children, bystanders, and pets away –

All spectators, including pets, should be kept a safe

distance away from the work area.

5. Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

6. Avoid Slipping – Exercise caution to avoid slipping or

falling. Wear protective footwear that will protect your feet

and improve your footing on slippery surfaces.

7. Stay alert – Watch what you are doing. Use common

sense. Do not operate the power tool when you are tired,

or under the inuence of alcohol or drugs.

8. Do not overreach – Keep proper footing and balance at

xall times.

9. Prevent unintentional starting – Do not pull the trigger

before connecting to battery pack, picking up or carrying

the appliance. Do not carry the pole + pruning saw with

your nger on the trigger.

10.

Use the right appliance – Do not use the power tool for

any applications other than those for which it was intended.

11. The chain is sharp – Don't grasp the exposed chain or

cutting edges when picking up or holding the power tool.

12. Use two hands – Hold the telescoping pole and handle

with both hands to avoid loss of control.

13. Remove the battery – Remove the battery from the

power tool when it is not in use, before servicing it, when

changing accessories, and when performing any other

maintenance task.

14.

Use safety glasses – Also use safety footwear, snug-tting

clothing, protective gloves, hearing and head protection.

15. Use head protection – Always use head protection when

operating the power tool overhead. Falling debris can

result in serious personal injury.

16. Do not force the tool – It will perform better with less

likelihood of personal or mechanical injury if it is used at

the rate for which it was designed.

17. Check for damaged parts – Before further use of the

appliance, all guards and parts should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other condition that may aect its

operation. A guard or other part that is damaged should

be properly repaired or replaced. Contact the Snow Joe®

+ Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563) for assistance.

18. Maintain the power tool with care – Keep the cutting

edges sharp and clean for optimal performance and to

reduce the risk of injury. Keep the handles dry, clean,

and free from oil and grease. Follow the additional

recommendations described in the maintenance section

of this manual.

19. Store indoors – When not in use, the power tool should

be stored indoors in a dry and high or locked-up place out

of the reach of children.

20. Do not use the power tool if the trigger does not turn it

on and o. Any power tool that cannot be controlled is

dangerous and must be repaired.

21. Keep all parts of the body away from the chain. Do not

remove cut material or hold material to be cut while the chain

is moving. Make sure the switch is o when clearing jammed

material. The chain will continue moving for a while after the

tool is turned o. A moment of inattention while operating the

power tool may result in serious personal injury.

22. Carry the power tool by the handle with the chain

stopped. When transporting or storing the power tool,

always keep the chain and guide bar in the bar sheath.

Proper handling of the pole + pruning saw will reduce the

chance of personal injury.

23. Hold the product by insulated surfaces only. In the event

that the chain comes into contact with hidden wiring,

exposed metal parts of the product may become “live”

and give the operator an electric shock.

24. The unit has not been designed to provide protection

from electric shock in the event of contact with overhead

electric lines. Never use the power tool near any electrical

power lines. Contact with or use near power lines may

cause serious injury or electric shock resulting in death.

Maintain a minimum clearance of 50 ft (15 m) from all

power lines.

mWARNING! Before inspecting, cleaning, or servicing

the machine, remove the battery and wait for all moving parts

to stop. Failure to follow these instructions can result in serious

personal injury or property damage.

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! Do not use the appliance within range of

persons unless they are wearing protective clothing.

mWARNING! Do not operate the cordless power tool in a

tree, on a ladder, or on scaolding. Using the tool under such

circumstances is extremely dangerous.

mWARNING! Do not let familiarity with this type of tool

prevent you from taking all necessary precautions. Remember

that a careless fraction of a second is sucient to inict

serious injury.

mWARNING! The cordless pole + pruning saw must be

fully assembled before operation! Do not use the tool that is

only partly assembled or assembled with damaged parts!

mWARNING! Starting, stopping, and restarting an electric

motor repeatedly within a few seconds can generate a great

deal of heat and damage the motor. To protect the life of your

cordless power tool, always wait at least ve seconds after

stopping before restarting the unit.

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects. If

you nd any, do not start up your machine and contact your

distributor.

NOTE: Take care of small parts that are removed during

assembly or when making adjustments. Keep them secure to

avoid loss.

Please contact an authorized Snow Joe® + Sun Joe® dealer

or call the Snow Joe® + Sun Joe® customer service center

at 1-866-SNOWJOE (1-866-766-9563) for all maintenance

or operations not foreseen in this manual. Any operation

performed in an unauthorized service center or by unqualied

personnel will completely invalidate the warranty.

mWARNING! For your safety and that of others:

• Correct maintenance is essential to maintain the original

eciency and safety of the machine over time.

• Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

• Never use the machine with worn or damaged parts.

Damaged parts are to be replaced and never repaired.

mWARNING! Always wear protective gloves during

maintenance operations.

mWARNING! Use only original manufacturer’s

replacement parts, accessories and attachments. Failure to do

so can cause possible injury and poor performance. To order

genuine replacement parts or accessories for the Sun Joe®

iON+ cordless pole + pruning saw, please visit sunjoe.com or

contact the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

Cleaning the Tool

mWARNING! Never let any liquid get inside the motor

housing and NEVER immerse any part of the housing in liquid.

1. Stop the motor and remove the battery.

2. Clean dirt and debris from the body of the tool, using a

damp cloth with a mild detergent.

Do not use any strong detergents on the plastic NOTE:

housing or the handle, as they can be damaged by certain

aromatic oils such as pine and lemon, and by solvents

such as acetone.

Storage

mWARNING! Do not at any time let brake uids, gasoline,

petroleum-based products, penetrating oils, solvents, etc.,

come in contact with plastic parts. Chemicals can damage,

weaken, or destroy plastic which may result in serious

personal injury.

1. Stop the motor and remove the battery.

2. Clean the pole + pruning saw thoroughly before storing.

3. Always place the bar sheath on the guide bar before

storing or transporting the pole + pruning saw. Use

caution to avoid the sharp chain.

4. Store the pole + pruning saw indoors, in a dry place that is

inaccessible to children. Keep away from corrosive agents

such as garden chemicals and de-icing salts.

5. We recommend using the original package for storage or

covering the product with a suitable cloth or enclosure to

protect it against dust.

Specic Safety Warnings

for Pole + Pruning saw

1. Only the pole + pruning saw operator should be in the

work area.

2. Do not use the pole + pruning saw to cut down trees.

3. Always use two hands when operating the pole + pruning

saw. Grip the pole + pruning saw securely with one hand

on the trigger and the other hand on the pole.

4. Before starting the pole + pruning saw, make sure that the

saw chain is not in contact with any object.

5. Do not allow the pole + pruning saw to make contact with

grounded objects such as pipes, fences, and metal posts.

6. Do not force the pole + pruning saw while cutting. Apply

light pressure. It will perform more eectively and safely if

it is used at the rate for which it was designed.

7. Use extreme caution when cutting a limb that is under

tension. When wood tension is released, the limb could

spring back and strike the operator, causing severe injury

or death.

8. During transport, hold the pole at its balance point, with

the guide bar and chain facing to the rear.

9. Do not cut small brush and saplings with the pole +

pruning saw. Small branches may catch in the chain and

be whipped towards the operator, which could pull the

operator o balance.

10. Never stand directly under the limb you are trimming.

Always position yourself outside the path of falling debris.

11. Keep a rm, steady pressure on the pole + pruning saw

while cutting. Do not try to cut limbs larger in diameter

than the length of the guide bar.

12. Keep other people and pets away from the cutting end of

the pole + pruning saw and at a safe distance away from

the work area.

Kickback

mWARNING! Kickback may occur when the nose or tip

of the guide bar touches an object, or when the wood closes

in and pinches the saw chain in the cut.

AVOID CONTACTING THE GUIDE BAR TIP WITH ANY

OBJECT. In some cases, when the tip makes contact with

an object, the saw may rapidly kick up and back towards the

operator. Material pinching the chain may also push the saw

back rapidly towards the operator. Either of these reactions

may cause you to lose control of the pole + pruning saw, which

could result in serious personal injury. Follow the necessary

precautions indicated below to avoid kickbacks.

• Always use two hands when operating the pole + pruning

saw, one hand gripping the trigger and the other hand

gripping the pole. Use a rm grip. Thumbs and ngers

must wrap around the trigger and the pole.

• Keep all guards in place on the pole + pruning saw. Make

sure they are in proper working order.

• Do not overreach or extend arms above shoulder height.

• Keep solid footing and balance at all times.

• Never try cutting through two branches at the same time.

Only cut one at a time.

• Do not bury the guide bar nose or try to cut by boring the

guide bar nose into the wood.

• Watch for shifting of wood or other forces that may pinch

the chain.

• Use extreme caution when re-entering a previous cut.

• Use the chain and guide bar supplied with this pole +

pruning saw. Only use genuine Snow Joe® + Sun Joe®

replacement parts designed specically for use with this

pole + pruning saw.

• Never use a dull or loose chain. Keep the chain sharp and

properly tensioned.

Battery & Charger

Safety Instructions

NOTE: This unit is the tool only. The battery and the charger

are not included. They must be purchased separately.

Model 24V-HCSWP-CT is compatible with the 24V iON+

System batteries and chargers. See page 21 for more

information.

We pay a great deal of attention to the design of every battery

pack to ensure that we supply you with batteries that are safe,

durable and have a high energy density. The battery cells have

a wide range of safety devices. Each individual cell is initially

formatted and its electrical characteristic curves are recorded.

This data is then used exclusively to be able to assemble the

best possible battery packs.

Despite all the safety precautions, caution must always be

exercised when handling batteries. The following points must

be obeyed at all times to ensure safe use. Safe use can only

be guaranteed if undamaged cells are used. Incorrect handling

of the battery pack can cause cell damage.

IMPORTANT! Analyses conrm that incorrect use and poor

care of high-performance batteries are the main factors

responsible for personal and/or product damage.

Product specificaties

Merk:	Sun Joe
Categorie:	Zaagmachine
Model:	24V-HCSWP-CT

Heb je hulp nodig?

Als je hulp nodig hebt met Sun Joe 24V-HCSWP-CT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Sun Joe

Sun Joe 20VIONLTE-CS10-RM Handleiding

15 November 2024

Sun Joe SWJ802E-PRP Handleiding

15 November 2024

Sun Joe iON8PS2 Handleiding

26 Juli 2023

Sun Joe 24V-HCSWP-CT Handleiding

2 Juli 2023

Sun Joe 24V-CSSHRP-LTE-RM Handleiding

20 Juni 2023

Sun Joe SWJ803E Handleiding

17 Juni 2023

Sun Joe SWJ599E Handleiding

4 Juni 2023

Sun Joe SWJ699E-RED-RM Handleiding

10 Mei 2023

Sun Joe 24V-PS10-CT Handleiding

7 Mei 2023

Sun Joe SWJ699E-RM Handleiding

5 Mei 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Herkules KS 210 Profi Handleiding

17 December 2024

Total TS730301 Handleiding

16 December 2024

Total TJSLI8501 Handleiding

16 December 2024

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024

Bavaria BJS 400 Handleiding

5 December 2024

Bavaria BCS 64/1 Handleiding

5 December 2024

Bavaria BEC 2040 TC Handleiding

5 December 2024

Einhell RT-SB 250 U Handleiding

4 December 2024

Einhell NSMS 4300 ZZ Handleiding

4 December 2024

Einhell RT-TS 2231 UD Handleiding

4 December 2024