Star Micronics SP500 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Star Micronics SP500 (124 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/124
DOT MATRIX PRINTER
SP500 SERIES
USER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE DI ISTRUZIONI
Federal Communications Commission
Radio Frequency Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interfer-ence
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own
expense.
This statement will be applied only for the equipments marketed in U.S.A.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
For compliance with the Federal Noise Interference Standard, this equipment requires a
shielded cable.
For RF interference suppression, if a ferrite core is provided with this device, affix it to the
interface cable.
Statement of
The Canadian Department of Communications
Radio Interference Regulations
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
The above statement applies only to printers marketed in Canada.
Trademark acknowledgments
SP500 Series: Star Micronics Co., Ltd.
ESC/POS: Seiko Epson Corporation
Notice
•All rights reserved. Reproduction of any part of this manual in any form whatsoever,
without STAR’s express permission is forbidden.
•The contents of this manual are subject to change without notice.
•All efforts have been made to ensure the accuracy of the contents of this manual at the
time of going to press. However, should any errors be detected, STAR would greatly
appreciate being informed of them.
•The above notwithstanding, STAR can assume no responsibility for any errors in this
manual.
© Copyright 2002-2010 Star Micronics Co., Ltd.
TABLE OF CONTENTS
1. Outline ...............................................................................................................1
2. Unpacking and Installation ................................................................................2
2-1. Unpacking .............................................................................................. 2
2-2. Locating the Printer ...............................................................................3
2-3. Handling Care ........................................................................................3
2-4. Maintenance ...........................................................................................3
3. Parts Identification and Nomenclature .............................................................. 4
4. Connecting Cables and Power Cord ..................................................................6
4-1. Connecting the Interface Cable .............................................................. 6
4-2. Connecting to a Peripheral Unit .............................................................7
4-3. Connecting the Power Cord ...................................................................8
4-4. Turning Power On .................................................................................9
4-5. Attaching the Rear Cover.......................................................................9
4-6. Installing the Cable ..............................................................................10
4-7. Switch Blind Installation .....................................................................11
5. Loading the Ribbon Cartridge and Paper ........................................................12
5-1. Tear Bar Model .................................................................................... 12
5-2. Auto Cutter Model ...............................................................................15
5-3. Installing the Roll Paper Guide ............................................................18
5-4 Clearing Paper Jams ............................................................................. 19
6. Control Panel and Other Functions .................................................................20
6-1. Control Panel .......................................................................................20
6-2. Basic Indicators ....................................................................................20
6-3. Errors ................................................................................................... 21
6-4. Adjustment Mode ................................................................................ 23
Appendix A: General Specifications .................................................................104
Appendix B: Serial Interface .............................................................................107
B-1. Pins and Signal Names ......................................................................107
B-2. Interface Connections ........................................................................ 108
Appendix C: Parallel Interface ..........................................................................109
C-1. Table of Connection Signals for Each Mode ..................................... 109
Appendix D: DIP Switch Setting ......................................................................111
D-1. Parallel Interface ................................................................................ 111
D-2. Serial Interface ...................................................................................112
Appendix E: Memory Switch Settings ..............................................................114
Appendix F: Peripheral Unit Driver Circuit ......................................................115
Appendix G: Adjusting the Dot Alignment Mode ............................................ 117
Appendix H: Black Mark Sensor Alignment Mode .......................................... 119


Product specificaties

Merk: Star Micronics
Categorie: Printer
Model: SP500

Heb je hulp nodig?

Als je hulp nodig hebt met Star Micronics SP500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Printer Star Micronics

Handleiding Printer

Nieuwste handleidingen voor Printer