Star Micronics TSP654IIBI-24 Handleiding

Star Micronics Printer TSP654IIBI-24

Lees hieronder de 📖 handleiding in het Nederlandse voor Star Micronics TSP654IIBI-24 (33 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/33

THERMAL PRINTER

TSP650II

SERIES

Hardware Manual

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) is device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, ax it to the interface cable.

is statement will be applied only for the printers marketed in U.S.A.

Statement of

e Canadian Department of Communications

Radio Interference Regulationst

is Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

e above statement applies only to printers marketed in Canada.

Caution Symbol

ese symbols are located near the thermal print head.

Because the thermal print head is hot immediately aer printing, do not touch it. Static

electricity can damage the thermal print head. To protect the thermal print head from

static electricity, do not touch it.

is symbol is located near the cutter.

Never touch the cutter blade, as you could injure your ngers.

is symbol is located near the peripheral drive connector.

Do not connect this to a telephone.

is symbol is located near the screws securing the case or the protective plate, which

should not be opened by individuals other than service personnel. Individuals, other

than service personnel, should not remove these screws. High voltage areas in the case

can be dangerous.

Trademark acknowledgments

TSP650II : Star Micronics Co., Ltd.

Notice

permission is forbidden.

• e contents of this manual are subject to change without notice.

• All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press.

However, should any errors be detected, STAR would greatly appreciate being informed of them.

• e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

2013-2014 Star Micronics Co., Ltd..

< For Bluetooth models >

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following

two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received,including interference that may cause undesired operation.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and

meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio

frequency (RF) Exposure rules. is equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation(MPE). But it is desirable that it should be installed and operated keeping

the radiator at least 20cm or more away from person's body (excluding extremities: hands,wrists,feet and ankles).

is statement will be applied only for the printers marketed in U.S.A and Canada.

CE MARKING WARNING

Hereby, Star Micronics Co., Ltd. declares that this device is in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Notice) is device can be operated in all European countries.

Italy: e public use is subject to general authorisation by the respective service provider.

Norway: is subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-

Alesund.

is statement will be applied only for the printers marketed in Europe.

Product specificaties

Merk:	Star Micronics
Categorie:	Printer
Model:	TSP654IIBI-24
Gewicht:	1720 g
Breedte:	142 mm
Diepte:	202 mm
Hoogte:	132 mm
Soort:	POS-printer
Bluetooth:	Ja
Connectiviteitstechnologie:	Draadloos
Ethernet LAN:	Nee
Certificering:	UL, C-UL, TüV, FCC, VCCI, EN55022, CE, Gost
Temperatuur bij opslag:	-20 - 60 °C
Compatibele besturingssystemen:	Windows 8.1\r\nWindows XP\r\nWindows Vista\r\nWindows 7\r\nWindows Server 2008\r\nWindows XP Embedded\r\nPOS Ready 2009\r\nOPOS\r\nJavaPOS\r\nLinux\r\nMac OS X\r\niOS\r\nAndroid\r\nBlackberry
Luchtvochtigheid bij opslag:	10 - 90 procent
Stroomverbruik:	1800 mA
Flash memory:	4 MB
Maximale resolutie:	203 x 203 DPI
Maximum roll diameter:	83 mm
Printtechnologie:	Direct thermisch
Standaard interfaces:	Bluetooth
Maximale print breedte:	72 mm
Printsnelheid (metrisch):	300 mm/sec
Bedrijfstemperatuur (T-T):	5 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Ondersteunde papierwijdte:	58/80 mm
Autocutter duurzaamheid:	2 miljoen delen