Star Micronics SM-S301-DB38 Handleiding

Star Micronics Labelprinter SM-S301-DB38

Lees hieronder de 📖 handleiding in het Nederlandse voor Star Micronics SM-S301-DB38 (23 pagina's) in de categorie Labelprinter. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/23

Mobile Printer

SM-S200 SERIES

Models: SM-S201

SM-S202

Hardware Manual

Federal Communications Commission

Radio Frequency Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

CAUTION: Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modications not expressly approved by the manufacturer could void the user’s authority to operated the equipment under

FCC rules.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio

frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it is

deemed to comply without testing of specic absorption ratio (SAR).

The above statement applies only to equipments marketed in U.S.A.

Trademark acknowledgments

SM-S200: Star Micronics Co., Ltd.

Notice

STAR’s express permission is forbidden.

• The contents of this manual are subject to change without notice.

• All efforts have been made to ensure the accuracy of the contents of this manual at the time of

going to press. However, should any errors be detected, STAR would greatly appreciate being

informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

Please follow the precautions below to enjoy and maintain the full performance of the printer.

■ Using the Printer

● Some semiconductor devices are easily damaged by static electricity. You should turn the

printer “OFF”, before you connect or removed the cable on the rear side, in order to guard

the printer against the static electricity. If the printer is damaged by the static electricity,

you should turn the printer “OFF”.

● Be careful not to drop or bump the printer on a hard surface.

● Do not install the printer in direct sunlight or such areas.

Suitable environment for the use of the printer is as follows:

Operating temperature :0 °C to 50 °C

Relative humidity : 30 % to 80 % (No condensation)

● Do not install the printer near devices that generate strong electromagnetic elds such as a

copy machine.

● Do not open the paper cover during printing .

● Do not remove or reinstall the communication cable during printing or transmission.

● Do not touch the connectors of the communication during printing.

● Switch the POWER OFF when not in use.

● Do not use alcohol or other solvent.

● The battery charger and the battery pack may become warm when in use. This is normal and

is not a malfunction.

● When the battery pack is used at low temperature, the length of time the printer can be used

may be shortened.

■ Thermal Paper Handling

● Store the thermal paper in a cool, dry and dark place.

● Do not rub the paper with hard object.

● Do not leave the paper with hard object.

● Do not allow plastic lm, erasers, or adhesive tape to touch the paper for long periods.

● Do not stack the thermal paper with diazo copies immediately after copying or wet-type

copies.

● Do not use chemical glue.

● Always use the clean thermal paper.

Operating precautions

Product specificaties

Merk:	Star Micronics
Categorie:	Labelprinter
Model:	SM-S301-DB38
Kleur van het product:	Zwart
Gewicht:	232 g
Breedte:	80.5 mm
Diepte:	113.5 mm
Hoogte:	46 mm
Kleur:	Ja
Bluetooth:	Ja
RS-232 port:	1
Compatibele besturingssystemen:	Windows 7 32/64 Bit\nWindows Vista 32/64 Bit\nWindows XP\nWindows CE\nWindows Mobile\nStarIO SDK with support for Android and Blackberry
Mediadikte:	0.06 - 0.07 mm
Maximum roll diameter:	39 mm
Printtechnologie:	Direct thermisch
Printsnelheid (metrisch):	80 mm/sec
Ondersteunde papierwijdte:	58 mm