Spektrum AR12010 Handleiding

Spektrum Radiografisch bestuurbaar speelgoed AR12010

Lees hieronder de 📖 handleiding in het Nederlandse voor Spektrum AR12010 (2 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Battery Requirements

Using One Battery

The AR12000 allows the option of using one or two battery packs. When using one battery, simply

plug the battery into either one of the two battery connectors (BATT 1 or BATT2). When using dual

batteries, it’s recommended that both batteries be of the same capacity, voltage and ideally of the

same age/previous prole. When using two batteries the total available capacity equals the sum

total of both batteries (e.g. BATT1- 2000mAh + BATT2- 2000mAh= a total capacity of 4000mAh).

Battery Capacity

It’s important to select a battery(s) that has more than adequate capacity to provide the necessary

ight time. Our staff has been recording in-ight data to determine typical current consumption

of aircraft in ight. Following are two graphs that illustrate the in-ight current draw of the radio

system.

Note: Current draws may vary depending on your servos, installation, and ying style.

The following setup is shown as a worst case scenario indicative of some aerobatic pilots’ setups. It

is not recommended to use this setup without proper voltage regulation for your servos.

Airplane - 40% YAK

File: JasonNoll.FDR Session:All Sessions

Sec son d

35 030 025 020 015 010 050

PackAmps_A

PackAmps_A: Min 0.00 Max 17.80 Avg 2.62

45 040 00

Servos - 9-JR8711’s 1-8317 (throttle)

Batteries - Two 4000mAh 2-cell 7.4-volt LiPo’s

Regulator - none

Note: JR8711’s and 8317’s are rated at a maximum of 6-volt 5-cell use. Using higher voltages will

void the warranty.

Engine - DA150

Weight - 40 lb

Flight envelope - Aggressive 3D

Average current - 2.62 amps

Peak current - 17.8 amps

Milliamps used per 10 minute ﬂight - 435mAh

In the example above, the average current was 2.62 amps, which calculates to 435mAh per 10

minutes (typical ight length). It’s recommended that only 60% of the available capacity be used to

ensure plenty of reserve battery capacity. In this example, using two 4000mAh batteries (8000mAh

total capacity) x 60%= 4800mAh (available usable capacity) divided by the capacity used per 10

minute ight, 435mAh would allow up to 11 ights of 10 minutes each.

AR12000 User Guide

The AR12000 full range 12-channel receiver features DSM2

™

technology and is compatible with all

Spektrum

™

and JR

® aircraft radios that support DSM2 technology including Spektrum DX7, Spektrum

DX6i, Spektrum DX5e, Spektrum Module Systems, JR12X, JRX9303.

Note: The AR12000 receiver is not compatible with the Spektrum DX6 parkflyer transmitter.

Features:

• 12-Channel Full Range Receiver with Dual Battery Ports

• Patented MultiLink™ receiver technology with up to four receivers

• Includes one internal and three remote receivers

• Two type of failsafe SmartSafe™ and Preset Failsafe

• QuickConnect™ with Brownout Detection

• Flight Log Compatible (optional)

Applications

Full Range Up to 12-channel aircraft including:

Giant-scale aircraft

Jets

Scale aircraft

Large scale helicopters

Giant-scale racing airplanes

Aircraft with multiple functions

Speciﬁcations:

Type: DSM2 Full Range Receiver

Channels: 12

Modulation: DSM2

Dimension (WxLxH): 46.5 x 52 x 15.3mm

Weight: 40 g

Input Voltage Range: 4.8–10V

Resolution: 2048

Items Included:

• Receiver main unit - SPMAR12000

• Three remote receivers - SPM9545

• One 24” remote receiver extension - SPM9013

• One 12” remote receiver extension - SPM9012

• One 9” remote receiver extension - SPM9011

• User Guide

• Male/Female bind plug - SPM6803

Optional Items

• Flight Log data recorder - SPM9540

• Replacement remote receiver - SPM9545

• 6” Remote receiver extension - SPM9010

• 9” Remote receiver extension - SPM9011

• 12” Remote receiver extension - SPM9012

• 24” Remote receiver extension - SPM9013

• 36” Remote receiver extension - SPM9014

• 6” Quick Disconnect Remote receiver extension - SPMAJST3

• 12” Quick Disconnect Remote receiver extension - SPMAJST6

Airplane - 33% Sukhoi

F e sukhio Seil : ss ssi :A Seon ll i son

PackAmps_A Min 0.: 0 0 Max 6. Avg 0.8292

Sec sond

45 040 035 030 025 020 015 010 0500

PackAmps_A

6.5

5.5

4.5

3.5

2.5

1.5

0.5

Servos - 7-JR8611’s 1-8317 (throttle)

Batteries - 1- 4000mAh 2-cell 7.4-volt LiPo’s

Regulator - 6 volts

Engine - DA100

Weight - 26 lb

Flight envelope - Moderate 3D

Average current - .82 amps

Peak current - 6.92 amps

Milliamps used per 10 minute ﬂight - 137mAh

Recommended Guidelines for Battery Capacity

40-45% Aerobatic aircraft w/ 9–12 high current servos: 4000-8000mAh

33-35% Aerobatic aircraft w/ 7–10 high current servos: 3000-6000mAh

25% Quarter Scale Aerobatic aircraft w/ 5–7 high current servos: 2000-4000mAh

Jets - BVM Super BANDIT, F86, Euro Sport, etc.: 3000-6000mAh

Giant-Scale Jets - BVM Ultra Bandit: 4000-8000mAh

Scale aircraft: The variety of scale aircraft and the accessories they use vary tremendously

making it difcult to give capacity recommendations for these types of aircraft. Using the above

aerobatic guidelines relative to the size and number of servos used will provide a conservative

capacity for your scale aircraft. As always, check battery charge condition before each ight.

IMPORTANT: DO not use a 4-cell 4.8-volt battery to power the receiver.

Four-cell 4.8-volt batteries do not provide enough voltage head room (additional margin needed)

necessary to power the system when heavily loaded. Under load, the system voltage can drop below

the voltage system’s minimum operating voltage threshold (3.5 volts) and cause loss of control.

The AR12000 is capable of handling voltages from 6.0 to 10.0 volts. The voltage limitations are

generally the servos. Most servos are compatible with 5-cell 6-volt packs, however, and 5-cell

6-volt NiMH packs have become the standard for many giant-scale applications.

Be aware that NiMH batteries have tendencies to false peak when being fast charged. Be especially

careful and sure when using NiMH batteries that they are fully charged and have not false peaked.

Many pilots are using 2-cell LiPo batteries to power their aircraft. LiPo’s offer greater capacity for

their size and weight, plus it is easier to manage the charging.

Receiver

The AR12000 incorporates one internal receiver, and requires at least two external receivers (three

are included) offering the security of multi-path RF redundancy. One internal receiver is located on

the main PC board, while two external receivers must be attached to the main board with exten-

sions. Additionally a fourth receiver is included and can be added offering the ultimate in RF link

security and redundancy. By locating each receiver in slightly different locations in the aircraft, each

receiver is exposed to its own RF environment, greatly improving path diversity (the ability for the

receiver to see the signal in all conditions).

Antenna Polarization

For optimum RF link performance it’s important that the antennas be mounted in an orientation that

allows for the best possible signal reception when the aircraft is in all possible attitudes and posi-

tions. This is known as antenna polarization. The antennas should be oriented perpendicular to each

other; typically vertical and horizontal and at different angles (see Receiver Installation below). The

remote receiver antenna should be mounted in a position perpendicular at least 2 inches away from

the main receiver’s antenna using double-sided foam tape.

Receiver Installation in Aircraft

In gas, turbine and glow aircraft install the main receiver using the same method you would use to

install a conventional receiver in your aircraft. Typically, wrap the main receiver in protective foam

and fasten it in place using rubber bands or hook and loop straps. Alternately, in electric airplanes

or helicopters, it’s acceptable to use thick double-sided foam tape to fasten the main receiver in

place. The AR12000 requires at least two remote receivers to operate. Mounting these remote receiv-

ers in different locations, even just inches away from the primary receiver, gives tremendous improve-

ments in path diversity. Essentially, each receiver sees a different RF environment and this is key to

maintaining a solid RF link, even in aircraft that have substantial conductive materials (e.g. larger gas

engines, carbon ber, pipes, etc.), which can weaken the signal. Using servo tape, mount the remote

receivers keeping the remote antennas at least 2 inches away from the primary antennas. Ideally, the

antennas will be oriented perpendicularly to each other. In airplanes, we’ve found it best to mount the

primary receiver in the center of the fuselage on the servo tray and to mount the remote receivers to the

side of the fuselage or in the turtle deck. A fourth antenna can be added for additional RF link security.

Important: Y-Harnesses and Servo Extensions

When using a Y-harness or servo extensions in your installation, it’s important to use standard non-

amplied Y-harnesses and servo extensions as this can/will cause the servos to operate erratically

or not function at all. Amplied Y-harnesses were developed several years ago to boost the signal

for some older PCM systems and should not be used with Spektrum equipment. Note that when

converting an existing model to Spektrum be certain that all ampled Y-harnesses and/or servo

extensions are replaced with conventional non-amplied versions.

Binding

The AR12000 receiver must be bound to the transmitter before it will operate. Binding is the process

of teaching the receiver the specic code of the transmitter so it will only connect to that specic

transmitter.

1. To bind an AR12000 to a DSM2 transmitter, insert the bind plug in the BATT/BIND port on the receiver.

2. Power the receiver. Note that the LED on all receivers should be ashing, indicating that the receiver

is in bind mode and ready to be bound to the transmitter.

Shown using a separate receiver pack.

(Battery can be plugged into either BATT port.)

3. Move the sticks and switches on the transmitter to the desired failsafe positions (low throttle and

neutral control positions).

4. Follow the procedures of your specic transmitter to enter Bind Mode, the system will connect

within a few seconds. Once connected, the LED on the receiver will go solid indicating the system

is connected.

5. Remove the bind plug from the BATT/BIND port on the receiver before you power off the transmitter

and store it in a convenient place.

6. After you’ve set up your model, it’s important to rebind the system so the true low throttle and

neutral control surface positions are set.

IMPORTANT: Remove the bind plug to prevent the system from entering bind mode the next time the

power is turned on.

Failsafe functions

The AR12000 features two types of failsafe: SmartSafe and Preset Failsafe.

SmartSafe

This type of failsafe is recommended for most types of aircraft. Here’s how SmartSafe works.

When the transmitter and receiver are turned on the receiver connects to the transmitter and nor

control of all channels occurs. If loss of signal occurs, SmartSafe drives the throttle servo only t

preset failsafe position (low throttle) that was set during binding. All other channels hold their la

position. When the signal is regained, the system immediately regains control.

Preset Failsafe

Preset failsafe is ideal for sailplanes and is preferred by some modelers for their glow- and gas-

powered aircraft.

When the transmitter and receiver are turned on and the receiver connects to the transmitter nor

control of all channels occurs. If loss of signal occurs Preset failsafe drives all servos to their preset

failsafe positions. For sailplanes it’s recommended that the spoilers/aps deploy to de-thermaliz

aircraft, preventing a yaway. Some powered modelers prefer to use this failsafe system to prog

slight turn and low throttle to prevent their aircraft from ying away. When the signal is regaine

system immediately regains control.

Programming SmartSafe

During the binding process the bind plug is left in throughout the process and is removed only a

the receiver connects to the transmitter. After the connection is made, conrmed by operating th

servos, the bind plug can be removed. The receiver is now programmed for SmartSafe.

Programming Preset Failsafe

During the binding process the bind plug is inserted in the bind port, then the receiver is powere

up. The LEDs in each receiver should blink, indicating that the receiver is in bind mode. Now b

binding the receiver to the transmitter and with the receiver in bind mode, remove the bind plug

LEDs will still be blinking. With the control sticks and switches in the desired failsafe positions

the transmitter to the receiver. Follow the procedures of your specic transmitter to enter Bind M

The system should connect in less than 15 seconds. The receiver is now programmed for preset

failsafe.

Note: Failsafe positions are stored via the stick and switch positions on the transmitter during bin

Receiver Power Only

• With SmartSafe or Preset Failsafe, when the receiver only is turned on (no transmitter signal is

present), the throttle channel has no output, to avoid operating or arming the electronic speed c

• All other channels are driven to their preset failsafe positions set during binding.

Note: Some analog servos may coast slightly even though no signal is present. This is normal

Plugging in the Leads

Plug the servo leads into the appropriate servo ports in the receiver noting the polarity of the

servo connector.

Range Testing

Before each ying session and especially with a new model, it is important to perform a range c

All Spektrum aircraft transmitters incorporate a range testing system which, when activated, red

the output power, allowing a range check.

Press and hold the bind button

30 paces (90 feet/28 meters)

1. With the model restrained on the ground, stand 30 paces (approx. 90 feet/28 meters) away from

the model.

y y g p p y

range check mode.

3. You should have total control of the model with the button depressed at 30 paces (90 feet/28 meters).

4. If control issues exist, call the Spektrum Service Center in the U.S. at 1-877-504-0233 for further

assistance. In the UK or Germany use one of the following addresses.

European Union: +49 4121 46199 66 (Deutschland)

or email service@horizonhobby.de

+44 (0) 1279 641 097 (United Kingdom)

or email sales@horizonhobby.co.uk

Advanced Range Testing

For sophisticated models that have signiﬁcant conductive material in them, the Advanced range test

using a ﬂight log is recommended. The advanced range check will conﬁrm that the internal and remote

receivers are operating optimally and that the installation (position of the receivers) is optimized for

the speciﬁc aircraft. This Advanced Range Check allows the RF performance of each receiver to be

evaluated and to optimize the locations of the remote receiver.

Advanced Range Test

1. Plug a Flight Log (SPM9540) into the data port in the AR12000 and turn on the system (Tx and Rx).

2. Advance the Flight Log until F- frame losses are displayed by pressing the button on the Flight Log.

3. Have a helper hold your aircraft while observing the Flight Log data.

4. Standing 30 paces away from the model, face the model with the transmitter in your normal ﬂying

position and put your transmitter into range test mode. This causes reduced power output from the

transmitter.

5. Have your helper position the model in various orientations (nose up, nose down, nose toward the

Tx, nose away from the Tx, etc.) while your helper watches the Flight Log noting any correlation

between the aircraft’s orientation and frame losses. Do this for 1 minute. The timer on the transmitter

can be used here. A successful advanced test will yield the following:

H- 0 holds

F- less than 10 frame losses

A, B, R, L- Frame losses will typically be less than 100. It’s important to compare the relative frame

losses and if a particular receiver has a signiﬁcantly higher frame loss value (2 to 3X) then the test

should be redone and if the same results occur, move the offending receiver to a different location.

Receiver Power System Requirements

Inadequate power systems that are unable to provide the necessary minimum voltage to the receiver

during ﬂight have become the number one cause of in-ﬂight failures. Some of the power system

components that affect the ability to properly deliver adequate power include

• Receiver battery pack (number of cells, capacity, cell type, state of charge)

• The ESC’s capability to deliver current to the receiver in electric aircraft

• The switch harness, battery leads, servo leads, regulators etc.

The AR12000 has a minimum operational voltage of 3.5 volts; it is highly recommended the power

system be tested per the guidelines below.

Recommended Power System Test Guidelines

If a questionable power system is being used (e.g. small or old battery, ESC that may not have a BEC

that will support high-current draw, etc.), it is recommended that a voltmeter be used to perform the

following tests.

Note: The Hangar 9 Digital Servo & Rx Current Meter (HAN172) or the Spektrum Flight Log

(SPM9540) is the perfect tool to perform the test below.

Plug the voltmeter into an open channel port in the receiver and with the system on, load the control

surfaces (apply pressure with your hand) while monitoring the voltage at the receiver. The voltage

should remain above 4.8 volts even when all servos are heavily loaded.

Note: The latest generations of Nickel-Metal Hydride batteries incorporate a new chemistry

mandated to be more environmentally friendly. These batteries when charged with peak detection

fast chargers have tendencies to false peak (not fully charge) repeatedly. These include all brands

of NiMH batteries. If using NiMH packs, be especially cautious when charging, making absolutely

y y g g p y g

capacity. Note the number of mAh put into a discharged pack to verify it has been charged to full

capacity.

QuickConnect™ With Brownout Detection

Your AR12000 features QuickConnect with Brownout Detection.

• Should an interruption of power occur (brownout), the system will reconnect immediately when

power is restored (QuickConnect).

• The LED on the receivers will ash slowly indicating a power interruption (brownout) has occurred.

• Brownouts can be caused by an inadequate power supply (weak battery or regulator), a loose

connector, a bad switch, an inadequate BEC when using an Electronic speed controller, etc.

• Brownouts occur when the receiver voltage drops below 3.5 volts thus interrupting control as the

servos and receiver require a minimum of 3.5 volts to operate.

How QuickConnect With Brownout Detection Works

• When the receiver voltage drops below 3.5 volts the system drops out (ceases to operate).

• When power is restored the receiver immediately attempts to reconnect to the last two frequencies

that it was connected to.

• If the two frequencies are present (the transmitter was left on) the system reconnects typically about

4/100 of a second.

QuickConnect with Brownout Detection is designed to allow you to y safely through most short

duration power interruptions, however, the root cause of these interruptions must be corrected before

the next ﬂight to prevent a crash.

Note: If a brownout occurs in ﬂight it is vital that the cause of the brownout be determined and corrected.

Flight Log (SPM9540 Optional)

The Flight Log is compatible with the AR9000. The Flight Log displays overall RF link performance as

well as the individual internal and external receiver link data. Additionally it displays receiver voltage.

Using the Flight Log

After a ﬂight and before turning off the receiver or transmitter, plug the Flight Log into the Data port on

the AR12000. The screen will automatically display voltage e.g. 6v2= 6.2 volts.

Note:

When the voltage reaches 4.8 volts or less, the screen will ﬂash indicating low voltage.

Press the button to display the following information:

A – Antenna fades on internal antenna A

B – Antenna fades on internal antenna B

L – Antenna fades on the left external antenna

R – Antenna fades on the right external antenna

F – Frame loss

H – Holds

Note:

– – – (three dashed lines) will appear if the antenna is not attached

Antenna fades—represents the loss of a bit of information on that speciﬁc antenna.

Typically it’s normal to have as many as 50 to 100 antenna fades during a ﬂight. If any single antenna

experiences over 500 fades in a single ﬂight, the antenna should be repositioned in the aircraft to

optimize the RF link.

Frame loss—represents simultaneous antenna fades on all attached receivers.

If the RF link is performing optimally, frame losses per ﬂight should be less than 20. A hold occurs

when 45 consecutive frame losses occur. This takes about one second. If a hold occurs during a ﬂight,

it’s important to evaluate the system, moving the antennas to different locations and or checking to be

sure the transmitter and receivers are all working correctly.

Note: A servo extension can be used to allow the Flight Log to be plugged in more conveniently.

On some models, the Flight Log can be plugged in, attached and left on the model using

double-sided tape. Mounting the Flight Log conveniently to the side frame is common with

helicopters.

Print ed 02/09 149

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept an

interference received, including interference that may cause undesired operation.

Caution: Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found

to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to

2.4835GHz frequency range.

CE Compliance information for the European Union

Declaration of Conformity

(in accordance with ISO/IEC 17050-1)

No. HH2008123101

Product(s): AR12000 Receiver

Item Number(s): SPMAR12000

The object of declaration described above is in conformity with the requirements of the speciﬁca-

tions listed below, following the provisions of the European R&TTE directive 1999/5/EC:

EN 301 489-1 v.1.6.1 General EMC requirements for Radio equipment

EN 301 489-17 v.1.2.1

Signed for and on behalf of:

Horizon Hobby, Inc.

Champaign, IL USA

Dec. 31, 2008

Steven A. Hall

Vice President

International Operations and Risk Management

Horizon Hobby, Inc.

4105 Fieldstone Road, Champaign, IL 61822 Call toll-free, 877-504-0233.

DSM and DSM2 are trademarks or registered trademarks of Horizon Hobby, Inc.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

US patent number 7,391,320. Other patents pending.

Inspection or Repairs

If this Product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA).

Pack the Product securely using a shipping carton. Please note that original boxes may be included, but

are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that

provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise

until it arrives and is accepted at our facility. A Service Repair Request is available at www.horizonhobby.

com on the “Support” tab. If you do not have internet access, please include a letter with your complete

name, street address, email address and phone number where you can be reached during business days,

your RMA number, a list of the included items, method of payment for any non-warranty expenses and a

brief summary of the problem. Your original sales receipt must also be included for warranty consideration.

Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase

date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge.

Repair or replacement decisions are at the sole discretion of Horizon Hobby.

Non-Warranty Repairs

Should your repair not be covered by warranty the repair will be completed and payment will be required

without notiﬁcation or estimate of the expense unless the expense exceeds 50% of the retail purchase cost.

By submitting the item for repair you are agreeing to payment of the repair without notiﬁcation. Repair

estimates are available upon request. You must include this request with your repair. Non-warranty repair

estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight.

Please advise us of your preferred method of payment. Horizon accepts money orders and cashiers checks,

as well as Visa, MasterCard, American Express, and Discover cards. If you choose to pay by credit card,

please include your credit card number and expiration date. Any repair left unpaid or unclaimed after 90

days will be considered abandoned and will be disposed of accordingly. Please note: non-warranty repair is

only available on electronics and model engines.

Electronics and engines requiring inspection or repair should be shipped to the following address:

Horizon Service Center

4105 Fieldstone Road

Champaign, Illinois 61822

All other Products requiring warranty inspection or repair should be shipped to the following address:

Horizon Product Support

4105 Fieldstone Road

Champaign, Illinois 61822

Please call 877-504-0233 or e-mail us at productsupport@horizonhobby.com with any questions or

concerns regarding this product or warranty.

European Union:

Electronics and engines requiring inspection or repair should be shipped to one of the following addresses:

Warranty Period

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”)

will be free from defects in materials and workmanship for a period of 1 year from the date of purchase by

the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE

PURCHASER. This warranty covers only those Products purchased from an authorized Horizon dealer.

Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims.

Further, Horizon reserves the right to change or modify this warranty without notice and disclaims all other

warranties, express or implied.

(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED,

ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE

PRODUCT. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE

PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

repair or (ii) replace, any Product determined by Horizon to be defective. In the event of a defect, these are

the Purchaser’s exclusive remedies. Horizon reserves the right to inspect any and all equipment involved

in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This warranty

does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence,

commercial use, or modication of or to any part of the Product. This warranty does not cover damage due

to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return

of any goods by Purchaser must be approved in writing by Horizon before shipment.

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.

Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability

is asserted. As Horizon has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability

shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the

user accepts all resulting liability.

If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product,

you are advised to return this Product immediately in new and unused condition to the place of purchase.

Law: These Terms are governed by Illinois law (without regard to conﬂict of law principals).

Safety Precautions

This is a sophisticated hobby Product and not a toy. It must be operated with caution and common sense

and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible

manner could result in injury or damage to the Product or other property. This Product is not intended

for use by children without direct adult supervision. The Product manual contains instructions for safety,

operation and maintenance. It is essential to read and follow all the instructions and warnings in the

manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly,

setup or use of the Product has been started, you must contact Horizon directly. This will enable Horizon to

better answer your questions and service you in the event that you may need any assistance. For questions

or assistance, please direct your email to productsupport@horizonhobby.com, or call 877.504.0233 toll

free to speak to the Product Support department.

Horizon Hobby UK

Units 1-4 Ployters Rd

Staple Tye, Harlow

Essex CM18 7NS

United Kingdom

Please call +44 (0) 1279 641 097 or email sales@horizonhobby.co.uk

with any questions or concerns regarding this product or warranty.

Horizon Technischer Service

Hamburger Str. 10

25335 Elmshorn

Germany

Please call +49 4121 46199 66 or email service@horizonhobby.de

with any questions or concerns regarding this product or warranty.

Instructions for Disposal of WEEE by Users in the

European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility

to dispose of their waste equipment by handing it over to a designated collection point for the

recycling of waste electrical and electronic equipment. The separate collection and recycling of yo

waste equipment at the time of disposal will help to conserve natural resources and ensure that it

recycled in a manner that protects human health and the environment. For more information about

where you can drop off your waste equipment for recycling, please contact your local city ofﬁce,

your household waste disposal service or where you purchased the product.

p g p

ModelMatch™

Some Spektrum and JR transmitters offer a patent pending feature called ModelMatch. ModelMatch

prevents the possibility of operating a model using the wrong model memory, potentially preventing a

crash. With ModelMatch each model memory has its own unique code (GUID) and during the binding

process the code is programmed into the receiver. Later, when the system is turned on, the receiver will

only connect to the transmitter if the corresponding model memory is programmed on screen.

Note: If at any time you turn on the system and it fails to connect, check to be sure the correct

model memory is selected in the transmitter. Please note that the DX5e and Aircraft Modules do

not have ModelMatch.

While your DSM equipped 2.4GHz system is intuitive to operate, functioning nearly identically to

72MHz systems, following are a few common questions from customers.

1. Q: Which do I turn on rst, the transmitter or the receiver?

A: If the receiver is turned off ﬁrst —all servos except for the throttle will be driven to their preset

failsafe positions set during binding. At this time the throttle channel doesn’t output a pulse

position preventing the arming of electronic speed controllers or in the case of an engine

powered aircraft the throttle servo remains in its current position. When the transmitter is

then turned on the transmitter scans the 2.4GHz band and acquires two open channels. Then

the receiver that was previously bound to the transmitter scans the band and ﬁnds the GUID

(Globally Unique Identiﬁer code) stored during binding. The system then connects and

operates normally.

If the transmitter is turned on ﬁrst—the transmitter scans the 2.4GHz band and acquires two

open channels. When the receiver is then turned on for a short period (the time it takes to

connect) all servos except for the throttle are driven to their preset failsafe positions while the

throttle has no output pulse. The receiver scans the 2.4GHz band looking for the previously

stored GUID and when it locates the speciﬁc GUID code and conﬁrms uncorrupted repeatable

packet information, the system connects and normal operation takes place. Typically this takes

2 to 6 seconds.

2. Q: Sometimes the system takes longer to connect and sometimes it doesn’t connect

at all?

A: In order for the system to connect (after the receiver is bound) the receiver must receive a large

number of consecutive uninterrupted perfect packets from the transmitter in order to connect.

This process is purposely critical of the environment ensuring that it’s safe to ﬂy when the system

does connect. If the transmitter is too close to the receiver (less than 4 ft.) or if the transmitter

is located near metal objects (metal TX case, the bed of a truck, the top of a metal work bench,

etc.) connection will take longer and in some cases connection will not occur as the system is

receiving reﬂected 2.4GHz energy from itself and is interpreting this as unfriendly noise. Moving

the system away from metal objects or moving the transmitter away from the receiver and

powering the system again will cause a connection to occur. This only happens during the initial

connection. Once connected the system is locked in and should a loss of signal occur (failsafe)

the system connects immediately (4ms) when signal is regained.

3. Q: I’ve heard that the DSM system is less tolerant of low voltage. Is this correct?

A: All DSM receivers have an operational voltage range of 3.5 to 9.6 volts. With most systems this

is not a problem as in fact most servos cease to operate at around 3.8 volts. When using multiple

high-current draw servos with a single or inadequate battery/power source, heavy momentary

loads can cause the voltage to dip below this 3.5-volt threshold thus causing the entire system

(servos and receiver) to brown out. When the voltage drops below the low voltage threshold

(3.5 volts), the DSM receiver must reboot (go through the startup process of scanning the band

and nding the transmitter) and this can take several seconds. Please read the receiver power

requirement section as this explains how to test for and prevent this occurrence.

4. Q: Sometimes my receiver loses its bind and won’t connect requiring rebinding.

What happens if the bind is lost in ight?

A: The receiver will never lose its bind unless it’s instructed to. It’s important to understand that

during the binding process the receiver not only learns the GUID (code) of the transmitter but

the transmitter learns and stores the type of receiver that it’s bound to. If the transmitter is placed

into bind mode, the transmitter looks for the binding protocol signal from a receiver. If no signal

is present, the transmitter no longer has the correct information to connect to a speciﬁc receiver

customers that use transmitter stands or trays that unknowingly depress the bind button and the

system is then turned on losing the necessary information to allow the connection to take place.

We’ve also had DX7 customers that didn’t fully understand the range test process and pushed the

bind button before turning on the transmitter also causing the system to “lose its bind.”

Age Recommendation: 14 years or over. This is not a toy. This product is not intended for use by

children without direct adult supervision.

Product specificaties

Merk:	Spektrum
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	AR12010
Kleur van het product:	Zwart
Gewicht:	40 g
Breedte:	46.5 mm
Hoogte:	15.3 mm
Soort:	Radio-Controlled (RC) Model Parts
Correct gebruik:	Vliegtuig
Merkcompatibiliteit:	Spektrum
Lengte:	52 m
Aantal:	1
Spanning:	4.8 - 10 V
Aantal kanalen:	12 kanalen
Type product:	Ontvanger
Frequentie microprocessor:	2400 MHz