SoundTube STNet Switch II Handleiding

SoundTube Receiver STNet Switch II

Lees hieronder de πŸ“– handleiding in het Nederlandse voor SoundTube STNet Switch II (2 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Quick Start Guideξ˜ƒLogin from Web Browser
orξ˜ƒseeξ˜ƒtheξ˜ƒreverseξ˜ƒofξ˜ƒthisξ˜ƒpageξ˜ƒtoξ˜ƒloginξ˜ƒwithξ˜ƒInstallξ˜ƒWizardξ˜ƒ
ο‚Œ Connect Switch to PC
Power up the switch and connect it via Ethernet LAN
cable to the Ethernet RJ45 connector on PC.
 Check the LED Statusξ˜ƒ
Step 1: Power up the switch and connect it to the
PC using an Ethernet cable.
Step 2: If the port LED is blinking, the switch is
ready.
ο‚Ž Set Up IP Address of PCξ˜ƒ
Step 1: Press WinKey+R and type ”ncpa.cpl” command.
Step 2: Right-click on your local adapter and select Properties
Step 3: In the Local Area Connection Properties window
highlight Internet Protocol Version 4 (TCP/IPv4) then
click the Properties button.
Step 4: Select the radio button Use the following IP
address and enter in the IP for the PC (in between
192.168.1.2 and 192.168.1.254), Subnet Mask (e.g.
255.255.255.0), and Default Gateway that corresponds
with your network setup. Then enter your Preferred and
Alternate DNS server addresses.
Step5: Click OK to change the PC’s IP address.
 Login Page
If your PC is configured correctly, you will see the
login page of the switch below.
ξ˜ƒ
 Enter the Factory Default IPξ˜ƒ
Run your Web browser on the PC, enter the factory
default IP address, so as to access the switch’s Web
interface.
Default IP 192.168.1.1
Subnet Mask 255.255.255.0
ο‚‘ξ˜ƒLogin to the Switchξ˜ƒ
Enter the factory default username and
password in login page. Click β€œLogin” to log
into the switch.
Default Username admin
No Factory Default Password
Quick Start Guideξ˜ƒLogin with Install Wizardξ˜ƒ ξ˜ƒ
orξ˜ƒseeξ˜ƒtheξ˜ƒreverseξ˜ƒofξ˜ƒthisξ˜ƒpageξ˜ƒtoξ˜ƒloginξ˜ƒfromξ˜ƒWebξ˜ƒBrowserξ˜ƒ
ο‚Œ Download Install Wizard
Download the Install Wizard via either of the three
following ways:
- http://www.channel-platform.com/INSTALL-WIZ
ARD/
- goo.gl/od0ZKr
- QR code below
ο‚Ž Check the LED Statusξ˜ƒ
Step 1: Power up the switch and connect it to the
PC using an Ethernet cable.
Step 2: Check if the port LED is blinking which
means the switch is ready.
 Connect Switch to PC
Power up the switch and connect it via Ethernet LAN
cable to the Ethernet RJ45 connector on PC.
 Execute Install Wizardξ˜ƒ
Run the Install Wizard on your PC.
The Install Wizard will auto scan the switches on the
local network once it is executed.
ξ˜ƒ
Click Scan
Scan
Scan
Scan Scan Ic
Ic
Ic
IcIcon
on
on
onon to discover other
switches which are just being added
to the network.
 Configuration
Step 1: Select a switch you want to configure.
Step 2: Click the Configure Icon and login.
Step 3: Mark the β€œManagement” as β€œEnable”.
Step 4: Configure basic features thru Install
Wizard (e.g. IP, NTP, Password, etc).
Default Username admin
No Factory Default Password
Step 3 is for Unmanaged+ Switch only.
ο‚‘ξ˜ƒLogin to Web UI
Step 1: Select a switch you want to configure.
Step 2: Click the Configure Icon and login.
Step 3: Mark the β€œManagement” as β€œEnable”.
Step 4: Click the Web GUI Icon and login.
Default Username admin
No Factory Default Password
Step 3 is for Unmanaged+ Switch only.


Product specificaties

Merk: SoundTube
Categorie: Receiver
Model: STNet Switch II

Heb je hulp nodig?

Als je hulp nodig hebt met SoundTube STNet Switch II stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver SoundTube

Handleiding Receiver

Nieuwste handleidingen voor Receiver