Soundskins SSK-GLDTR Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Soundskins SSK-GLDTR (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
Jeep JK/JL/Gladiator Kit Instructions
3a. Next, you need to prop the window up out of the way.
For JLs and Gladiators, turn the accessory on, pop open the
two circular rubber service caps on the door panel, and row
the window around 3/4 of the way down until the bolts are
centered in the cap holes. Then, pull the clips connected to
the glass up. This will allow you to remove the glass and
slide it all the way up to install the kit. Prop the window up
with a rubber wedge covered by a microfiber cloth or place
a screwdriver in the hole underneath the window to prop the
glass up.
1. Start by locating the fastening hardware on the door
panel, take the appropriate screw driver and remove. Once
all the screws are removed you can take off the door panel
gently, watching that you don’t break any of the clips or
mounting hardware.
2. Pull the panel away slowly and unplug any electrical
connections. Under the panel, you will find plastic insert
over the metal door.
R
• Drill with socket set and extension
• Panel/trim tool
• Roller
• Razor blade
• Screw driver
• Rubber wedge
• Microber cloth
• Acetone or cleaning solution
• Shop vacuum
Tools needed for installation:
4. Note that the plastic inserts do not need to be completely
removed to install the door pieces, you can simply hold it off
to the side or have a friend help as you install the material.
Now you are ready to prep the metal surface with a microfiber
cloth and Acetone (use a breathing mask). Wipe away any
moisture, oil, debris, etc. Then let air dry. The point is to get
the surface clean to ensure material glue contact.
3b. To prop the windows up for JKs, remove the 10mm bolts
around the plastic insert and disconnect the wire harnesses.
Peel the panel back and pull the toward you. Then find the
alginment pin located between the insert and door connected
to the bottom of the glass and disconnect it from the glass.
This will allow you to slide the glass up. Prop the window up
with a rubber wedge covered by a microfiber cloth.
5. Locate the piece of the kit with the label on the back that
coincides with the door you’re working on. Make sure it lines
up and is correct before pulling the white cover paper off,
then pull off the white paper and start placing the material at
the top and work your way down. Use a roller to apply the
material completely. Use a razor blade point or needle to
release any air bubbles. Repeat these steps for all door
panels, then reverse the process to replace your doors.
6. Next, you will need to disconnect your car batteries before
removing the seats. You will need to disconnect the negative
battery terminal. If your JL has an extra battery, be sure to
disconnect that as well by disconnecting the secondary
ground cable from the 13mm lug.
You can double check that your batteries are correctly
disconnected by going back inside your car and turning on
your dome light. If it does not turn on, you have completed
this step correctly.
8. Once you clear seats, can start working up the carpet. It
will be a bit more difficult because it’s molded to the floor.
Remove the carpet completely and lay it down on a flat
surface in order to not damage integrity of the material. Now
wipe down the floorboards as you did the door panels (you
may need a vacuum depending on how dirty your floors are).
If you wish, you can also remove your door seals.
7. Remove the front seats and the carpets. Use the
appropriate size socket set. There are four bolts per front
seat - remove the yellow electrical seat plug and then
remove the seats, being careful not to scratch the seats
against your car.
The rear seats don’t need to be removed completely, just
remove the front bolts and lift the bottom up. If you have a
Gladiator, remove the two plastic tubs below the backseat
which are held down with 10mm bolts as well as the jack
section.
9. Start with the front pieces and find the label that coincides
with the floor section. Make sure to check it first to ensure
that it fits in the designated area. Once confirmed, pull the
white paper off and apply the material with a roller, starting
from one side and working the material back.
10. Continue to the mid section that will have holes and will
be directional from left mid and right mid. Make sure to
confirm before rolling down.


Product specificaties

Merk: Soundskins
Categorie: Niet gecategoriseerd
Model: SSK-GLDTR

Heb je hulp nodig?

Als je hulp nodig hebt met Soundskins SSK-GLDTR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Soundskins

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd