Soundskins SSK-BRONCO Handleiding

Soundskins Niet gecategoriseerd SSK-BRONCO

Lees hieronder de 📖 handleiding in het Nederlandse voor Soundskins SSK-BRONCO (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 112 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Bronco Kit Installation Instructions

1. Start by locating the fastening hardware on the door panels.

There will be one behind the door handle under a plastic cover,

one behind the door grab handle that you will have to pop out to

reveal, and 2 at the bottom right corner of the door panels. Take a

7 mm socket and remove. Then, use a panel tool to pry the panel

off the door, start from the bottom right corner. Be sure not to break

any clips or mounting hardware.

3. Then, start applying the door pieces. Peel off the backing paper

starting at the top, tack the piece onto the door and work your way

down, pressing down the material and pulling down the backing

paper more as you go along. Remember to feed the harnesses

through the proper holes and ensure all holes are aligned properly

before pressing the entire piece down. Repeat steps 1-3 for all 4

doors.

4. Before removing the front seats, you MUST disconnect the

negative terminal of your car battery with a 10 mm bolt. Now, you

can work on removing the front seats. There are 13 mm bolts

covered by plastic cover plates on both sides underneath the seats

- you will need a T20 torx bit to remove them. Then, disconnect the

harness by sliding the red security tab out of the way and pinching

the connector. Then, carry the seats out of the car.

2. Pull the door panel away slowly. There will be 2 plug clips that

will need to be released as well as a wire plug to disconnect. Set

the door panel aside and unhook all plugs, remove the vapor

barrier, and clean the car metal surface using a microfiber cloth

and Acetone or other cleaning solution. The point is to get the

surface clean to ensure material glue contact.

• Drill

• 7mm, 10 mm, 13mm, 18mm socket

• Socket extension

• T20, T30, T55 torx bit

• Panel/trim tool

• Roller

• Flat head screw driver

• 3/8” Ratchet

• Microber cloth

• Acetone or cleaning solution

• Shop vacuum

• Tarp, cloth, blanket, or towel

Tools needed for installation:

Scan this code to watch the

full instructional video!

8. Insert a trim tool between the selector lever boot and the trim

ring to release the tabs and lift the boot upwards. Then,

disconnect all the plugs in the center console.

5. The next step is to take apart the center console. Remove the

trim panel underneath the dash stereo - it will snap outward.

7. Then, remove the center console main top piece. It will

unsnap through the seam area as seen in the photo to the left.

6. Next, remove the grip handle on the center console on the

passenger side that is held by 2 T30 bolts.

9. There will be a black plastic keeper crossing over the top of

the center console held by 7 mm bolts. Remove this piece.

13. Go back to the door cabin and remove the door seals on each

door. Then, in the driver seat floor section, remove the kick panel

on the left foot rest using an extension and 10mm tool. Pull out the

bolts and remove this kick panel (shown in the photo to the left).

12. Head to the trunk. Remove the trim plate behind the backseats

to reveal some 18 mm bolts (shown in the photo to the left).

Remove the bolts, then remove the backseats. We recommend

taking out the smaller seat first, then bringing the larger one out

after. Disconnect the two plugs in the backseat area.

10. Locate the two 7mm bolts on each side of the center console

covered by plastic keepers. Remove these bolts and take out the

final piece of the center console.

11. Remove the backseats. There will be bolts at the bottom and

nuts in the center of the seats that need to be removed in order to

take the bottom brackets of the seats off. Then, there will be 18 mm

bolts that hold the brackets for the seats and seatbelts, as well as

T55s holding the seatbelts on each side that will need to be

removed.

14. Then, remove the B pillar plastic covers located in between the

front and back doors. They should unsnap easily.

Product specificaties

Merk:	Soundskins
Categorie:	Niet gecategoriseerd
Model:	SSK-BRONCO

Heb je hulp nodig?

Als je hulp nodig hebt met Soundskins SSK-BRONCO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Soundskins

Soundskins SSK-GLDTR4DR Handleiding

6 April 2024

Soundskins SSK-RDGLD14 Handleiding

6 April 2024

Soundskins Rings v3 SSK-RINGS Handleiding

6 April 2024

Soundskins SSK-STGLD14 Handleiding

6 April 2024

Soundskins SSK-SEK Handleiding

6 April 2024

Soundskins SSK-F2504DR Handleiding

6 April 2024

Soundskins SSK-RAP4DR Handleiding

6 April 2024

Soundskins SSK-BRONCO Handleiding

6 April 2024

Soundskins Pro Plus SSPROPLUS-1 Handleiding

6 April 2024

Soundskins SSK-TCM4DR Handleiding

6 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

MGW Diamond-HX OG Handleiding

23 November 2024

Electrolux STA9 Handleiding

23 November 2024

Electrolux UMP3 Handleiding

23 November 2024

Electrolux ZS70GL Handleiding

23 November 2024

Bosch HEZ8TK36UC Handleiding

23 November 2024

Bosch HEZ8ZZ36UC Handleiding

23 November 2024

Bosch HDZIT301 Handleiding

23 November 2024

Bosch HEZBS301 Handleiding

23 November 2024

LG LX-330 Handleiding

23 November 2024

Stamos S-PLASMA 60U Handleiding

23 November 2024