Skytech 3002 Handleiding

Skytech Diversen klimaatbeheersing 3002

Lees hieronder de 📖 handleiding in het Nederlandse voor Skytech 3002 (10 pagina's) in de categorie Diversen klimaatbeheersing. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
INSTALLATION AND OPERATING INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT
TO INSTALL OR OPERATE
Model: 3002
INTRODUCTION
This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas
heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio
frequencies (RF) within a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are
programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.
Review COMMUNICATION SAFETY under theTRANSMITTER SECTION and THERMO SAFETY under the REMOTE RECEIVER
SECTION. These signal/temperature safety features shut down the appliance when a potentially unsafe condition exists.
REV. 4-19-12 Page 1
Skytech: 3002
The transmitter operates on (2) AAA-size 1.5V batteries. It is recommended that ALKALINE batteries always be used for
longer battery life and maximum operational performance. IMPORTANT: New or fully charged batteries are essential for
proper operation of the multi-function transmitter. Insert (2) AAA-size 1.5 V batteries into the battery compartment on the
back of the transmitter, positioning the (+) and (-) ends of the batteries as indicated on the casing. When the batteries are
inserted, gure #2 (with similar numbers) will display.
Fig. 1 Transmitter Front and Back Views
Note: If a LOW battery icon appears on the screen,
check the position of the batteries.
CAUTION: Due to the sensitive temperature-monitoring
components in the transmitter, it may be necessary to
allow the transmitter to stabilize to room temperature
before accurate room temperatures are displayed on
the screen. If the transmitter is activated from a
severe cold condition, it can take up to fteen minutes
for accurate temperature readings to appear.
1. BATTERY ICON - Symbol means battery power is low. Replace batteries within 2-weeks.
2. TIMER- Indicates time remaining before system shuts OFF, when timer-programmed; 9-hour maximum setting.
3. MODE- Indicates operation MODE of system. ON indicates the system is manually ON. OFF indicates the entire
system is turned OFF and THERMO indicates the system will automatically cycle ON/OFF, depending on the SET
temperature.
4. SET- Indicates desire SET room temperature for THERMO operation.
5. FLAME – Indicates burner/valve in ON position.
6. CLOCK – Indicates the current time in AM/PM
7. ROOM – Indicates CURRENT room temperature.
8. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).
LCD DISPLAY FUNCTIONS
ROOM
SET
1
23
4
5
6
7
8
Fig. 2 LCD Display Functions
MODE
COVER CLOSED
MODE
TIMER
TIME
SET
SLIDE COVER
OPEN
+
+
-
-
AAA
BACK OF
TRANSMITTER
Skytech: 3002 REV. 4-19-12 Page 2
BASIC TRANSMITTER FUNCTIONS
To understand the operation of the transmitter, press and release the MODE button (Fig. 3) until the LCD screen reads
OFF in the display (Fig. 4).
Step 1: Press the MODE button one time to manually turn ON the appliance (Fig. 5).
Step 2: Press the MODE button a second time to put the to put the system in THERMO mode (Fig. 6).
Step 3: Press the MODE button a third time to turn the appliance back OFF again as show in (Fig. 4).
Fig. 4 OFF Mode
ROOM
SET
Fig. 5 Manual ON
ROOM
SET
Fig. 6 Thermo Mode
ROOM
SET
Slide down the lower section of the cover on the front of the transmitter to expose the “SET” buttons (Fig. 1). The slide
cover protects the SET buttons from being changed accidentally. Close the cover after completing the following settings/
programming.
Blinking numbers on the LCD display indicate the system is awaiting user input, such as using the UP and DOWN buttons
to program a new setting. If no change is made to ashing digits within 15-seconds, the system will complete the
procedure last programmed and reset the display to its normal state.
SETTING UP THE TRANSMITTER
SETTING THE CLOCK
1. Press and hold the TIMER/TIME button on the transmitter
for more than 2-seconds (Fig. 7). The hour digit(s) will begin
blinking (Fig. 8)..
2. Press the UP or DOWN button until the desired hour is
displayed in AM or PM.
3. After setting the desired hour, press and release the TIMER/
TIME button again to set the minutes; the minute digits will
begin blinking (Fig. 9)..
4. Press the UP or DOWN button until the desired minutes are
displayed.
5. Press and hold the TIMER/TIME button again for more than
2-seconds. The time digits will cease blinking, indicating the
clock has been successfully set. You may also press the
SET button on the transmitter to stop the time digits from
blinking and set the time.
ROOM
SET
ROOM
SET
Fig. 8 SettingHours Fig. 9 Setting Minutes
Fig. 3 Mode Button
MODE
Fig. 7 Timer/Time Button
Skytech: 3002 REV. 4-19-12 Page 3
The factory setting for temperature is ÂșF. To change this setting to ÂșC, rst press and hold
the UP and DOWN buttons on the transmitter at the same time (Fig. 10). Follow this same
procedure to change from ÂșC back to ÂșF. When changing between the ÂșF and ÂșC scales, the
temperature in the SET frame defaults to the lowest temperature (45Âș F, or 6Âș C). The
highest SET temperature is 99Âș Fahrenheit (32Âș Celsius).
SETTING ÂșF / ÂșC SCALE
The remote receiver operates on (4) AA-size 1.5V batteries.
It is recommended that ALKALINE batteries be used for
longer battery life and maximum microprocessor
performance. IMPORTANT: New or fully charged batteries
are essential for proper operation of the remote receiver.
The remote receiver houses the microprocessor that
responds to commands from the transmitter to control
system operation. It emits one beep when it receives an
ON or OFF command manually, but no beep when cycling
on and off automatically in THERMO mode. The remote
receiver has a 3-position slide switch (Fig. 11) for selecting
the ON/REMOTE/OFF mode of operation:
‱ With the slide switch in the ON position (toward the LEARN button), the system will remain ON until the slide
switch is placed in the OFF or REMOTE position.
‱ With the slide switch in the REMOTE position (centered), the system will only operate if the remote receiver
receives commands from the transmitter.
‱ With the slide switch in the OFF position (away from the LEARN button), the system is OFF.
‱ It is suggested that the slide switch be placed in the OFF position if you will be away from your home for an
extended period of time. If the remote receiver is mounted out of children’s reach, placing the slide switch in the
OFF position also functions as a safety “lock-out” by both turning the system off and rendering the remote receiver
inoperative.
REMOTE RECEIVER
REMOTE
ON
OFF
LEARN
Requires 4-AA 1.5V
alkaline batteries
Learning
button
Remote Receiver
Battery cover slides on/off
Slide
Switch
ON
REMOTE
OFF
Fig. 11 Remote Receiver
INSTALLATION PRECAUTIONS
This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely
before attempting installation. Follow instructions carefully during installation. Any modications of the SKYTECH
remote control or any of its components will void the warranty and may could cause a re hazard.
Do not connect any gas valve or electronic module directly to 110-120VAC power. Consult gas appliance manufac-
turer’s instructions and wiring schematics for proper placement of all wires. All electronic modules are to be wired to
manufacturer’s specications.
The following wiring diagrams are for illustration purpose only. Follow instructions from manufacturer of gas valve and/
or electronic module for correct wiring procedures. Improper installation of electric components can cause damage to
electronic module, gas valve and remote receiver.
WARNING
Fig. 10 Temperature Scale
MODE

Product specificaties

Merk: Skytech
Categorie: Diversen klimaatbeheersing
Model: 3002

Heb je hulp nodig?

Als je hulp nodig hebt met Skytech 3002 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Diversen klimaatbeheersing Skytech

Skytech

Skytech 3002 Handleiding

9 Januari 2023

Handleiding Diversen klimaatbeheersing

Nieuwste handleidingen voor Diversen klimaatbeheersing

Oregon Scientific

Oregon Scientific BA169 weer hub Handleiding

16 Oktober 2023
Riello

Riello BGK0.1 Handleiding

14 Oktober 2023
Premix

Premix XR-Serie Handleiding

27 September 2023
Elektrobock

Elektrobock RJ 402 Handleiding

11 September 2023
Elektrobock

Elektrobock RJ 401 Handleiding

11 September 2023
Elektrobock

Elektrobock RJ 403 Handleiding

11 September 2023
DGFlow

DGFlow Presflo Handleiding

6 September 2023
Sonnenkonig

Sonnenkonig FRIGORA 500-24F Handleiding

3 September 2023
Kaysun

Kaysun KC-FCD2 Handleiding

17 Augustus 2023
Plugwise

Plugwise Switch Handleiding

24 Juli 2023