Shelly WiFi Relay Switch Handleiding

Shelly Schakelaar WiFi Relay Switch

Lees hieronder de 📖 handleiding in het Nederlandse voor Shelly WiFi Relay Switch (2 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

USER GUIDE

WiFi Relay Switch

fig. 1

LEGEND:

N - Neutral input (Zero)/( + )

L - Line input (110-240V)/( - )

O - Output

I - Input

SW - Switch (input) controlling O

Power supply:

• 110-240V ±10% 50/60Hz AC

• 30-50V DC

• 12V DC

Max load:

16A/240V

Complies with EU standards:

• RE Directive 2014/53/EU

• LVD 2014/35/EU

• EMC 2004/108/WE

• RoHS2 2011/65/UE

Working temperature:

– 20°C up to 40°C

Radio signal power:

1mW

Radio protocol:

WiFi 802.11 b/g/n

Frequency:

2400 – 2500 MHz;

Operational range (depending on local construction):

• up to 50 m outdoors

• up to 30 m indoors

Dimensions (HxWxL):

41 x 36 x 17 mm

Electrical consumption:

< 1 W

The WiFi Relay Switch Shelly

® 1 may control 1 electrical cir-

cuit up to 3.5 kW. It is intended to be mounted into a standard

in-wall console, behind power sockets and light switches or

other places with limited space. Shelly may work as a stan-

dalone Device or as an accessory to another home automa-

tion controller.

• Purpose of control: Operating

• Construction of control: Independently mounted

• Type 1.B Action

• Pollution Degree 2

• Impulse Voltage: 4000 V

Hazardous voltage presents on bridge in the top side of

the product!

Technical Information

• Control through WiFi from a mobile phone, PC, automa-

tion system or any other Device supporting HTTP and/or

UDP protocol.

• Microprocessor management.

• Controlled elements: 1 electrical circuits/appliances.

• Controlling elements: 1 relays.

• Shelly may be controlled by an external button/switch.

CAUTION! Danger of electrocution. Mounting the

Device to the power grid has to be performed with

caution.

CAUTION! Do not allow children to play with the

button/switch connected the Device. Keep the De-

vices for remote control of Shelly (mobile phones,

tablets, PCs) away from children.

Introduction to Shelly®

Shelly® is a family of innovative Devices, which allow remote

control of electric appliances through mobile phone, PC or

home automation system. Shelly® uses WiFi to connect to

the devices controlling it. They can be in the same WiFi net-

work or they can use remote access (through the Internet).

Shelly® may work standalone, without being managed by a

home automation controller, in the local WiFi network, as well

as through a cloud service, from everywhere the User has

Internet access.

Shelly® has an integrated web server, through which the User

may adjust, control and monitor the Device. Shelly

® has two

WiFi modes - access Point (AP) and Client mode (CM). To

operate in Client Mode, a WiFi router must be located within

the range of the Device. Shelly

® devices can communicate

directly with other WiFi devices through HTTP protocol.

An API can be provided by the Manufacturer. Shelly

® devices

may be available for monitor and control even if the User is

outside the range of the local WiFi network, as long as the

WiFi router is connected to the Internet. The cloud function

could be used, which is activated through the web server of

the Device or through the settings in the Shelly Cloud mobile

application.

The User can register and access Shelly Cloud, using either

Android or iOS mobile applications, or any internet browser

and the web site: https://my.Shelly.cloud/.

Installation Instructions

CAUTION! Danger of electrocution. The mounting/

installation of the Device should be done by a qual-

ied person (electrician).

CAUTION! Danger of electrocution. Even when the

Device is turned off, it is possible to have voltage

across its clamps. Every change in the connection

of the clamps has to be done after ensuring all local power

is powered off/disconnected.

CAUTION! Do not connect the Device to appliances

exceeding the given max load!

CAUTION! Connect the Device only in the way

shown in these instructions. Any other method

could cause damage and/or injury.

CAUTION! Before beginning the installation please

read the accompanying documentation carefully

and completely. Failure to follow recommended

procedures could lead to malfunction, danger to your life or

violation of the law. Allterco Robotics is not responsible for

any loss or damage in case of incorrect installation or oper-

ation of this Device.

CAUTION! Use the Device only with power grid and

appliances which comply with all applicable regu-

lations. short circuit in the power grid or any appli-

ance connected to the Device may damage the Device.

RECOMMENDATION: Тhe Device may be connect-

ed to and may control electric circuits and appli-

ances only if they comply with the respective

standards and safety norms.

RECOMMENDATION: The Device may be connect-

ed with solid single-core cables with increased

heat resistance to insulation not less than PVC

T105°C.

Initial Inclusion

Before installing/mounting the Device ensure that the grid is

powered off (turned down breakers).

Connect the Relay to the power grid and install it in the con-

sole behind the switch/power socket following the scheme

that suites the desired purpose:

1. Connecting to the power grid with power supply 110-240V

AC or 30-50V DC– g. 1

2. Connecting to the power grid with power supply 12 DC -

g. 2

For more information about the Bridge, please visit:

http://shelly-api-docs.shelly.cloud/#shelly-family-overview

or contact us at: developers@shelly.cloud

You may choose if you want to use Shelly with the Shelly

Cloud mobile application and Shelly Cloud service. You can

also familiarize yourself with the instructions for Manage-

ment and Control through the embedded Web interface.

Control your home with your voice

All Shelly devices are compatible with Amazon Echo and

Google Home.

Please see our step-by-step guide on:

https://shelly.cloud/compatibility/Alexa

https://shelly.cloud/compatibility/Assistant

MOBILE APPLICATION FOR

MANAGMENT OF SHELLY®

Shelly Cloud gives you opportunity to control and adjust all

Shelly® Devices from anywhere in the world.

You only need an internet connection and our mobile appli-

cation, installed on your smartphone or tablet.

To install the application please visit Google Play (Android - g.

3) or App Store (iOS - g. 4) and install the Shelly Cloud app.

Registration

The rst time you load the Shelly Cloud mobile app, you have to

create an account which can manage all your Shelly

® devices.

Forgotten Password

In case you forget or lose your password, just enter the e-mail

address you have used in your registration. You will then re-

ceive instructions to change your password.

WARNING! Be careful when you type your e-mail

address during the registration, as it will be used in

case you forget your password.

First steps

After registering, create your rst room (or rooms), where you

are going to add and use your Shelly devices.

Shelly Cloud gives you opportunity to create scenes for auto-

matic turning on or off of the Devices at predened hours or

based on other parameters like temperature, humidity, light

etc. (with available sensor in Shelly Cloud).

Shelly Cloud allows easy control and monitoring using a mo-

bile phone, tablet or PC.

Device Inclusion

To add a new Shelly device, install it to the power grid fol-

lowing the Installation Instructions included with the Device.

Step 1

After the installation of Shelly following the Instalation In-

structions and the power is turned on, Shelly will create its

own WiFi Access Point (AP).

WARNING: In case the Device has not created its’

own AP WiFi network with SSID like shelly1-

35FA58, please check if the Device is connected accordingly

to the Instalation Instructions. If you still do not see an ac-

tive WiFi network with SSID like shelly1-35FA58, or you want

to add the Device to another Wi-Fi network, reset the Device.

If the Device has been powered on, you have to restart by

powering it off and on again. After turning the power on, you

have one minute to press 5 consecutive times the button/

switch connected SW. You have to hear the Relay trigger it-

self. After the trigger sound, Shelly should return to AP

Mode. If not, please repeat or contact our customer support

at: support@Shelly.cloud

Step 2

Choose “Add Device”.

In order to add more Devices later, use the app menu at the

top right corner of the main screen and click “Add Device”.

Type the name (SSID) and password for the WiFi network, to

which you want to add the Device.

Step 3

If using iOS: you will see the following screen:

Press the home button of your iPhone/iPad/iPod. Open

Settings > WiFi and connect to the WiFi network created by

Shelly, e.g. shelly1-35FA58.

If using Android: your phone/tablet will automatically scan

and include all new Shelly Devices in the WiFi network that

you are connected to.

Upon successful Device Inclusion to the WiFi network you will

see the following pop-up:

Specification

fig. 2

fig. 3 fig. 4

Power supply: 110-240V AC

Bridge

Serial Port

O I SW L N

Power supply: 12V; 30-50V DC

O I SW L N

Bridge

Serial Port

12V DC

30-50V DC

The Embedded Web Interface

Еven without the mobile app, Shelly can be set and controlled

through a browser and WiFi connection of a mobile phone,

tablet or PC.

ABBREVIATIONS USED:

Shelly-ID – the unique name of the Device. It consists of 6

or more characters. It may include numbers and letters, for

example 35FA58.

SSID – the name of the WiFi network, created by the Device,

for example shelly1-35FA58.

Access Point (AP) – the mode in which the Device creates its

own WiFi connection point with the respective name (SSID).

Client Mode (CM) – the mode in which the Device is connect-

ed to another WiFi network.

Initial inclusion

Step 1

Install Shelly to the power grid following the schemes de-

scribed above and place it into the console. After turning the

power on Shelly will create its own WiFi network (AP).

WARNING: If you do not see an active WiFi network

with SSID like shelly1-35FA58, reset the Device. If

the Device has been powered on, you have to restart by pow-

ering it off and on again. After turning the power on, you have

one minute to press 5 consecutive times the button/switch

connected to SW. You have to hear the Relay trigger itself.

After the trigger sound, Shelly should return to AP Mode. If

not, please repeat or contact our customer support at: sup-

port@Shelly.cloud

Step 2

When Shelly has created an own WiFi network (own AP), with

name (SSID) such as shelly1-35FA58. Connect to it with your

phone, tablet or PC.

Step 3

Type 192.168.33.1 into the address eld of your browser to

load the web interface of Shelly.

General - Home Page

This is the home page of the embedded web interface. If it

has been set up is correctly, you will see information about:

• Settings menu button

• Current state (on/off)

• Present time

Settings – General Settings

In this menu, you can congure the Shelly device’s work and

connection modes.

WiFi Settings – the WiFi connection settings.

Access Point (AP) Mode: allows the Device to operate as a

WiFi access point. The User can change the name (SSID) and

the password to access the AP. After you have entered the

desired settings, press .Connect

WiFi Client Mode (CM): allows the Device to connect to an

available WiFi network. In order to switch to this mode, the

User must enter the name (SSID) and the password to con-

nect to a local WiFi network. After entering the correct details,

press .Connect

ATTENTION! If you have entered incorrect informa-

tion (wrong settings, usernames, passwords etc.),

you will not be able to connect to Shelly and you have to re-

set the Device.

WARNING: If you do not see an active WiFi net-

work with SSID like shelly1-35FA58, reset the De-

vice. If the Device has been powered on, you have to restart

by powering it off and on again. After turning the power on,

you have one minute to press 5 consecutive times the but-

ton/switch connected to SW. You have to hear the Relay

trigger itself. After the trigger sound, Shelly should return to

AP Mode. If not, please repeat or contact our customer sup-

port at: support@Shelly.cloud

Leave Unprotected - removing the notication for disabled

authorization.

Enable Authentication – you can turn authentication on or

off

This is where you can change your username and password.

You must enter a new username and the new password, then

press to save the changes.Save

Connect to Cloud: you can turn the connection between

Shelly and Shelly Cloud on or off.

Factory reset: Return Shelly to its factory settings.

Firmware Upgrade: Shows present rmware version. If a

newer version is available, you can update your Shelly Device

by clicking Update.

Device Reboot: Reboots the Device.

Managing in Relay Mode

Relay Screen

In this screen you can control, monitor and change the set-

tings for turning the power on and off. You can also see the

current status of the connected appliance to Shelly, Buttons

Settings, On and OFF.

To control Shelly press Relay:

To turn on the connected circuit press “Turn ON”.

To turn off the connected circuit press “Turn OFF”

Press the icon to go to the previous menu.

Shelly Management Settings

Each Shelly can be congured individually. This lets you per-

sonalize each Device in a unique manner, or consistently, as

you choose.

Power On Default State

This sets the relays’ default state when powered from the

power grid.

ON: By default when the Device is powered and the connect-

ed circuit/appliance to it will be powered as well.

OFF: By default the Device and any connected circuit/appli-

ance will not be powered, even when it is connected to the grid.

Restore Last State: By default the Device and the connected

circuit/appliance will be returned to the last state they occu-

pied (on or off) before the last power off/shutdown.

Auto ON/OFF

Automatic powering/shutdown of the socket and the con-

nected appliance:

Auto OFF after: After turning on, the power supply will be

automatically shut down after a predened time (in seconds).

A value of 0 will cancel the automatic shutdown.

Auto ON after: After turning off, the power supply will be au-

tomatically turned on after a predened time (in seconds). A

value of 0 will cancel the automatic start.

Manual Switch Type

• Momentary – When using a button.

• Toggle Switch – When using a switch.

• Edge switch - Change status on every hit.

Sunrise/Sunset hours

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with а working Internet connection.

Shelly receives actual information through the Internet about

the time of sunrise and sunset in your area. Shelly may turn

on or off automatically at sunrise/sunset, or at a specied

time before or after sunrise/sunset.

On/Off schedule

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with working internet connection.

Shelly may turn on/off automatically at a predened time.

Shelly may turn on/off automatically at a predefined time.

Manufacturer: Allterco Robotics EOOD

Address: Soa, 1407, 103 Cherni vrah Blvd.

Tel.: +359 2 988 7435

E-mail: support@shelly.cloud

http://www.Shelly.cloud

The Declaration of Conformity is available at:

https://Shelly.cloud/declaration-of-conformity/

Changes in the contact data are published by the Manufac-

turer at the ocial website of the Device:

http://www.Shelly.cloud

The User is obliged to stay informed for any amendments of

these warranty terms before exercising his/her rights against

the Manufacturer.

All rights to trademarks She® and Shelly® , and other intel-

lectual rights associated with this Device belong to Allterco

Robotics EOOD.

Step 4:

Approximately 30 seconds after discovery of any new Devic-

es оn the local WiFi network, а list will be displayed by default

in the “Discovered Devices” room.

Step 5:

Enter Discovered Devices and choose the Device you want to

include in your account.

Step 6:

Enter a name for the Device (in the Device Name eld). Choose a

Room, in which the Device has to be positioned. You can choose

an icon or add a picture to make it easier to recognize. Press

“Save Device”.

Step 7:

To enable connection to the Shelly Cloud service for remote

control and monitoring of the Device, press “YES” on the fol-

lowing pop-up.

Shelly Devices Settings

After your Shelly device is included in the application, you can

control it, change its settings and automate the way it works.

To switch the Device on and off, use the respective ON/OFF

button.

To enter at the details menu of the respective Device, simply

click on it’s name.

From the details menu you may control the Device, as well as

edit its appearance and settings.

EDIT DEVICE – allows you to change the Device’s name, room

and picture.

DEVICE Settings – allows you to change settings. For ex-

ample, with Restrict login you may enter a username and

password to restrict access to the embedded web interface

in Shelly. You may automate the Device operations from this

menu as well.

Timer

Тo manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automatically

shutdown after a predened time (in seconds). A value of 0 will

cancel the automatic shutdown.

Auto On: After turning off, the power supply will be automati-

cally turned on after a predened time (in seconds). A value of

0 will cancel the automatic power-on.

Weekly schedule

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with working internet connection.

Shelly may turn on/off automatically at a predened time and

day throughout the week. You may add unlimited number of

weekly schedules.

Sunrise/Sunset

This function requires an Internet connection. To

use Internet, a Shelly Device has to be connected to

a local WiFi network with а working Internet connection.

Shelly receives actual information through the Internet about

the time of sunrise and sunset in your area. Shelly may turn on

or off automatically at sunrise/sunset, or at a specied time

before or after sunrise/sunset.

Settings:

Power On Default Mode

Тhis setting controls whether the Device will supply power

or not the output as a default whenever it is receiving power

from the grid:

ON: When the Device is powered, by default the socket will

be powered.

OFF: Even if the Device is powered, by default the socket will

not be powered.

Restore Last Mode: When power is restored, by default, the

appliance will return to the last state it was in before the last

power off/shutdown.

Button Type

• Momentary - Set Shelly input to be buttons. Push for ON,

push again for OFF.

• Toggle Switch - Set Shelly input to be ip switches, with

one state for ON and another state for OFF.

Firmware Update: Shows present rmware version. If a new-

er version is available, you can update your Shelly Device by

clicking Update.

Factory reset: Remove Shelly from your account and return

it to its factory settings.

Device Information: Here you can see the unique ID of Shelly

and the IP it got from the Wi-Fi network.

Product specificaties

Merk:	Shelly
Categorie:	Schakelaar
Model:	WiFi Relay Switch

Heb je hulp nodig?

Als je hulp nodig hebt met Shelly WiFi Relay Switch stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Schakelaar Shelly

Shelly 1PM Handleiding

17 Juli 2023

Shelly Pro 4PM Handleiding

17 Juli 2023

Shelly 1L Handleiding

17 Juli 2023

Shelly Plus 1PM Handleiding

17 Juli 2023

Shelly Plus 2PM Handleiding

17 Juli 2023

Shelly Pro 2 Handleiding

17 Juli 2023

Shelly WiFi Relay Switch Handleiding

12 Mei 2023

Handleiding Schakelaar

Nieuwste handleidingen voor Schakelaar

Digitus DN-80112-2 Handleiding

27 December 2024

Adder Link INFINITY Dual 2112T Handleiding

26 December 2024

Adder Link INFINITY 1002 Handleiding

26 December 2024

D-Link DIS-100G-S5W Handleiding

24 December 2024

D-Link DGS-3630-28TC Handleiding

23 December 2024

D-Link DES-1228 Handleiding

23 December 2024

D-Link DES-1008F Handleiding

23 December 2024

Adder View Secure AVS 2114 Handleiding

23 December 2024

D-Link DES-1024R+ Handleiding

23 December 2024

D-Link DES-1016R+ Handleiding

23 December 2024