Shelly RGBW2 Handleiding

Shelly Smarth home RGBW2

Lees hieronder de 📖 handleiding in het Nederlandse voor Shelly RGBW2 (2 pagina's) in de categorie Smarth home. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

USER GUIDE

Smart WiFi LED Controller

Power supply:

12 or 24V DC

Power output (12V):

• 144W - combined power

• 45W - per channel

Power output (24V):

• 288W - combined power

• 90W - per channel

Complies with EU

standards:

• RE Directive 2014/53/EU

• LVD 2014/35/EU

• EMC 2004/108/WE

• RoHS2 2011/65/UE

Working temperature:

from -20°C to 40°C

Radio signal power:

1mW

Radio protocol:

WiFi 802.11 b/g/n

Frequency:

2400 – 2500 MHz;

Operational range

(depending on local

construction):

• up to 20 m outdoors

• up to 10 m indoors

Dimensions (HxWxL):

43 x 38 x 14 mm

Electrical consumption:

< 1 W

The RGBW2 WiFi LED Controller Shelly® by Allterco Ro-

botics is intended to be installed directly to a LED strip/

light in order to control the color and dimming of the light.

Shelly may work as a standalone device or as an accessory to

a home automation controller.

Technical Information

• Control through WiFi from a mobile phone, PC, automation

system or any other Device supporting HTTP and/or UDP

protocol.

• Microprocessor management.

• Controlled elements: multiple white and colour (RGB) LED

diods.

• Shelly may be controlled by an external button/switch.

CAUTION! Danger of electrocution. Mounting the Device

to the power grid has to be performed with caution.

CAUTION! Do not allow children to play with the button/

switch connected the Device. Keep the Devices for remote

control of Shelly (mobile phones, tablets, PCs) away from

children.

Introduction to Shelly®

Shelly® is a family of innovative Devices, which allow remote

control of electric appli-ances through mobile phone, PC or

home automation system. Shelly® uses WiFi to connect to

the devices controlling it. They can be in the same WiFi net-

work or they can use remote access (through the Internet).

Shelly® may work standalone, without being managed by a

home automation controller, in the local WiFi network, as well

as through a cloud service, from everywhere the User has

Internet access.

Shelly® has an integrated web server, through which the User

may adjust, control and monitor the Device. Shelly

® has two

WiFi modes - access Point (AP) and Client mode (CM). To

operate in Client Mode, a WiFi router must be located within

the range of the Device. Shelly

® devices can communicate

directly with other WiFi devices through HTTP protocol.

An API can be provided by the Manufacturer. Shelly

® devices

may be available for monitor and control even if the User is

outside the range of the local WiFi network, as long as the

WiFi router is connected to the Internet. The cloud function

could be used, which is activated through the web server of

the Device or through the settings in the Shelly Cloud mobile

application.

The User can register and access Shelly Cloud, using either

Android or iOS mobile applications, or any internet browser

and the web site: https://my.Shelly.cloud/.

Installation Instructions

CAUTION! Danger of electrocution. The mounting/

installation of the Device should be done by a qualified

person (electrician).

CAUTION! Danger of electrocution. Even when the

Device is turned off, it is possible to have voltage across its

clamps. Every change in the connection of the clamps has to

be done after ensuring all local power is powered off/

disconnected.

CAUTION! Do not connect the Device to appliances

exceeding the given max load!

CAUTION! Connect the Device only in the way shown in

these instructions. Any other method could cause damage

and/or injury.

CAUTION! Before beginning the installation please read

the accompanying documentation carefully and completely.

Failure to follow recommended procedures could lead to

malfunction, danger to your life or violation of the law.

Allterco Robotics is not responsible for any loss or damage in

case of incorrect installation or operation of this Device.

CAUTION! Use the Device only with power grid and

appliances which comply with all applicable regulations.

short circuit in the power grid or any appliance connected to

the Device may damage the Device.

RECOMMENDATION: Тhe Device may be connected to

and may control electric circuits and appliances only if they

comply with the respective standards and safety norms.

RECOMMENDATION: The Device may be connected to

and may control electric circuits and light sockets only if they

comply with the respective standards and safety norms.

Initial Inclusion

Before installing/mounting the Device ensure that the grid is

powered off (turned down breakers).

Connect the Shelly to the power grid following the wiring

scheme above (g.1). You may choose if you want to use

Shelly with the Shelly Cloud mobile application and Shelly

Cloud service. You can also familiarize yourself with the in-

structions for Management and Control through the embed-

ded Web interface.

Control your home with your voice

All Shelly devices are compatible with Amazon Echo and

Google Home.

Please see our step-by-step guide on:

https://shelly.cloud/compatibility/Alexa

https://shelly.cloud/compatibility/Assistant

MOBILE APPLICATION FOR

MANAGMENT OF SHELLY®

Shelly Cloud gives you opportunity to control and adjust all

Shelly® Devices from anywhere in the world.

You only need an internet connection and our mobile applica-

tion, installed on your smartphone or tablet.

To install the application please visit Google Play (Android - g.

2) or App Store (iOS - g. 3) and install the Shelly Cloud app.

fig. 2 fig. 3

Registration

The rst time you load the Shelly Cloud mobile app, you have to

create an account which can manage all your Shelly

® devices.

Forgotten Password

In case you forget or lose your password, just enter the e-mail

address you have used in your registration. You will then re-

ceive instructions to change your password.

WARNING! Be careful when you type your e-mail address

during the registration, as it will be used in case you forget

your password.

After registering, create your rst room (or rooms), where you

are going to add and use your Shelly devices.

Shelly Cloud gives you opportunity to create scenes for auto-

matic turning on or off of the Devices at predened hours or

based on other parameters like temperature, humidity, light

etc. (with available sensor in Shelly Cloud).

Shelly Cloud allows easy control and monitoring using a mo-

bile phone, tablet or PC.

Device Inclusion

To add a new Shelly device, install it to the power grid fol-

lowing the Installation Instructions included with the Device.

Step 1

After the installation of Shelly and the power is turned on

Specification

RGBW

LEGEN

I - Switch input (AC or DC) for on/off/dimming

DC - + 12/24V DC power supply

GND

12/24V DC power supply

R - Red light control

G - Green light control

B - Blue light control

W - White light control

Shelly will create its own WiFi Access Point (AP).

WARNING: In case the Device has not created its own

WiFi network with SSID like shellyrgbw2-35FA58 check if you

have connected Shelly correctly by the scheme in Fig. 1. If

you do not see an active WiFi network with SSID like

shellyrgbw2-35FA58, reset the Device. If the Device has

been powered on, you have to power it off and on again. After

turning the power on, you have 20 seconds to press 5

consecutive times the switch connected DC (SW). Or if you

have physicall access to the Device, press the reset button

once. The LED strip light will begin to flash. After the device

has began to flash, turn the power off and back on again.

Shelly should return to AP Mode. If not, please repeat or

contact our customer support at: support@Shelly.cloud

Step 2

Choose “Add Device”.

In order to add more Devices later, use the app menu at the

top right corner of the main screen and click “Add Device”.

Type the name (SSID) and password for the WiFi network, to

which you want to add the Device.

Step 3

If using iOS: you will see the following screen:

Press the home button of your iPhone/iPad/iPod. Open

Settings > WiFi and connect to the WiFi network created by

Shelly, e.g. shellyrgbw2-35FA58.

If using Android: your phone/tablet will automatically scan

and include all new Shelly Devices in the WiFi network that

you are connected to.

Upon successful Device Inclusion to the WiFi network you will

see the following pop-up:

Step 4:

Approximately 30 seconds after discovery of any new Devic-

es оn the local WiFi network, а list will be displayed by default

in the “Discovered Devices” room.

Step 5:

Enter Discovered Devices and choose the Device you want to

include in your account.

Step 6:

Enter a name for the Device (in the Device Name eld). Choose a

Room, in which the Device has to be positioned. You can choose

an icon or add a picture to make it easier to recognize. Press

“Save Device”.

Step 7:

To enable connection to the Shelly Cloud service for remote

control and monitoring of the Device, press “YES” on the fol-

lowing pop-up.

Shelly Devices Settings

After your Shelly device is included in the app, you can control

it, change its settings and automate the way it works.

To switch the Device on and off, use the respective ON/OFF

button.

To enter at the details menu of the respective Device, simply

click on it’s name.

From the details menu you may control the Device, as well as

edit its appearance and settings.

Work Modes - Shelly RGBW2 has two work modes: Color and

White

Color - In Color mode you have a full color gamma to choose

the desired color from.

Under the color gamma you have 4 pure predened colors –

Red, Green, Blue & Yellow. Below the predened colors you have

the dimmer slider from which you can vary the Shelly RGBW2`s

brightness.

White - In White mode you have four separate channels, each

with On/Off button and a dimmer slider - from which you can set

the desired brightness for the corresponding channel of Shelly

RGBW2.

Edit Device

From here you can edit:

• Device Name

• Device Room

• Device Picture

When you are done, press Save Device.

Timer

Тo manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automatically

shutdown after a predened time (in seconds). A value of 0 will

cancel the automatic shutdown.

Auto ON: After turning off, the power supply will be automati-

cally turned on after a predened time (in seconds). A value of

0 will cancel the automatic power-on.

Weekly Schedule

This function requires an Internet connection.

To use Internet, a Shelly Device has to be connected to a local

WiFi network with working internet connection.

Shelly may turn on/off automatically at a predefined time.

Multiple schedules are possible.

Sunrise/Sunset

This function requires an Internet connection.

Shelly receives actual information through the Internet about the

time of sunrise/sunset in your area. Shelly may turn on or off

automatically at sunrise/sunset, or at a specified time before or

after sunrise/sunset. Multiple schedules are possible.

Internet/Security

WiFi Mode - Client: Allows the device to connect to an avail-

able WiFi network. After typing the details in the respective

elds, press Connect.

WiFi Mode - Acess Point: Congure Shelly to create a Wi-Fi

Access point. After typing the details in the respective elds,

press Create Access Point.

Cloud: Enable or Disable connection to the Cloud service.

Restrict Login: Restrict the web interface of Shely with a User-

name and Password. After typing the details in the respective

elds, press Restrict Shelly.

Settings

Power On Default Mode

This sets the default output state when Shelly is powered.

ON: Congure Shelly to turn ON, when it has power.

OFF: Congure Shelly to turn OFF, when it has power.

Restore Last Mode: Congure Shelly to return to last state it

was in, when it has power.

Firmware Update

Update the rmware of Shelly, when a new version is released.

Time Zone and Geo-location

Enable or Disable the automatic detection of Time Zone and

Geo-location.

Factory Reset

Return Shelly to its factory default settings.

Device Information

Here you can see the:

• - Unique ID of ShellyDevice ID

• - The IP of Shelly in your Wi-Fi networkDevice IP

The Embedded Web Interface

Еven without the mobile app, Shelly can be set and controlled

through a browser and WiFi connection of a mobile phone,

tablet or PC.

ABBREVIATIONS USED:

Shelly-ID 6– the unique name of the Device. It consists of

or more characters. It may include numbers and letters, for

example 35FA58.

SSID – the name of the WiFi network, created by the Device,

for example shellyrgbw2-35FA58.

Access Point (AP) – the mode in which the Device creates its

own WiFi connection point with the respective name (SSID).

Client Mode (CM) – the mode in which the Device is connect-

ed to another WiFi network.

Initial inclusion

Step 1

Install Shelly to the power grid following the schemes de-

scribed above and urn it on. Shelly will create its own WiFi

network (AP).

WARNING: In case the Device has not created its own

WiFi network with SSID like shellyrgbw2-35FA58 check if you

have connected Shelly correctly by the scheme in Fig. 1. If

you do not see an active WiFi network with SSID like

shellyrgbw2-35FA58, reset the Device. If the Device has

been powered on, you have to power it off and on again. After

turning the power on, you have 20 seconds to press 5

consecutive times the switch connected DC (SW). Or if you

have physicall access to the Device, press the reset button

once. The LED strip light will begin to flash. After the device

has began to flash, turn the power off and back on again.

Shelly should return to AP Mode. If not, please repeat or

contact our customer support at: support@Shelly.cloud

Step 2

When Shelly has created an own WiFi network (own AP), with

name (SSID) such as shellyrgbw2-35FA58. Connect to it

with your phone, tablet or PC.

Step 3

Type 192.168.33.1 into the address eld of your browser to

load the web interface of Shelly.

Home Page

This is the home page of the embedded web interface. If it

has been set up is correctly, you will see information about:

• Current work mode - color or white

• Current state (on/off)

• Current brightness level

• Power button

• Connection to Cloud

• Present time

• Settings

Timer

Тo manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automatically

shutdown after a predened time (in seconds). A value of 0 will

cancel the automatic shutdown.

Auto ON: After turning off, the power supply will be automati-

cally turned on after a predened time (in seconds). A value of

0 will cancel the automatic power-on.

Weekly Schedule

This function requires an Internet connection.

To use Internet, a Shelly Device has to be connected to a local

WiFi network with working internet connection.

Shelly may turn on/off automatically at a predefined time.

Multiple schedules are possible.

Sunrise/Sunset

This function requires an Internet connection.

Shelly receives actual information through the Internet about

the time of sunrise/sunset in your area. Shelly may turn

on or off automatically at sunrise/sunset, or at a specified

time before or after sunrise/sunset. Multiple schedules are

possible.

Internet/Security

WiFi Mode - Client: Allows the device to connect to an avail-

able WiFi network. After typing the details in the respective

elds, press Connect.

WiFi Mode - Acess Point: Congure Shelly to create a Wi-Fi

Access point. After typing the details in the respective elds,

press Create Access Point.

Cloud: Enable or Disable connection to the Cloud service.

Restrict Login: Restrict the web interface of Shely with a User-

name and Password. After typing the details in the respective

elds, press Restrict Shelly.

ATTENTION! If you have entered incorrect information

(wrong settings, usernames, passwords etc.), you will not be

able to connect to Shelly and you have to reset the Device.

WARNING: In case the Device has not created its own

WiFi network with SSID like shellyrgbw2-35FA58 check if you

have connected Shelly correctly by the scheme in Fig. 1. If

you do not see an active WiFi network with SSID like

shellyrgbw2-35FA58, reset the Device. If the Device has

been powered on, you have to power it off and on again. After

turning the power on, you have 20 seconds to press 5

consecutive times the switch connected DC (SW). Or if you

have physicall access to the Device, press the reset button

once. The LED strip light will begin to flash. After the

device has began to flash, turn the power off and

back on again. Shelly should return to AP Mode. If

not, please repeat or contact our customer support

at: support@Shelly.cloud

Advanced - Developer Settings: Here you can

change the action execution:

• Via CoAP (CoIOT)

• Via MQTT

Firmware Upgrade: Shows present rmware version. If a

newer version is available, ocially announced and published

by the Manufacturer, you can update your Shelly Device. Click

Upload to install it to your Shelly Device.

Settings

Power On Default Mode

This sets the default output state when Shelly is powered.

ON: Congure Shelly to turn ON, when it has power.

OFF: Congure Shelly to turn OFF, when it has power.

Restore Last Mode: Congure Shelly to return to last state it

was in, when it has power.

Time Zone and Geo-location

Enable or Disable the automatic detection of Time Zone and

Geo-location.

Firmware Update: Update the rmware of Shelly, when a new

version is released.

Factory Reset: Return Shelly to its factory default settings.

Device Reboot: Reboots the device.

Device Information

Here you can see the unique ID of Shelly.

Additional Features

Shelly allows control via HTTP from any other device, home

automation controller, mobile app or server.

For more information about the REST control protocol, please visit:

https://shelly.cloud/developers/ or send a request to:

developers@shelly.cloud

Environmental Protection

This marking on the device, accessories, or documentation

indicates that the device and its electronic accessories

(charger, USB cable) must be disposed only in specially des-

ignated locations.

This marking on the battery, the instruction manual, the safe-

ty instructions, the warranty card or the packaging indicates

that the battery in the device must be disposed only in spe-

cially designated locations.

Please follow the instructions for environmental protection

and proper disposal of the Device, its accessories, and its

packaging for the recycling of the materials for their further

usage and to keep the environment clean!

Warranty Terms

1. The Device’s warranty term is 24 (twenty four) months, begin-

ning since the date of purchase by the End User. The Manufac-

turer does is not responsible for extra warranty terms by the Еnd

Seller.

2. The Warranty is valid for the territory of EU. The warranty is ap-

plicable in compliance with all relevant laws and users’ rights pro-

tections. The purchaser of the Device is entitled to exercise his/

her rights in accordance with all applicable laws and regulations.

3. Warranty terms are provided by Allterco Robotics EOOD (re

ferred hereinafter as the Manufacturer), incorporated under the

Bulgarian law, with address of registration 109 Bulgaria Blvd,

oor 8, Triaditsa Region, Soa 1404, Bulgaria, registered with the

Commercial Register kept by the Bulgarian Ministry of Justice’s

Registry Agency under Unied Identity Code (UIC) 202320104.

4. Claims regarding the Conformity of the Device with the terms

of the contract of sale shall be addressed to the Seller, in accor-

dance with its terms of sale.

5. Damages such as death or body injury, deterioration or dam

ages to objects different from the defective product, caused by

a defective product, are to be claimed against the Manufacturer

using the contact data of the Manufacturer’s company.

6. The User may contact the Manufacturer at support@shelly.

cloud for operational problems that may be resolved remotely. It

is recommended that the User contact the Manufacturer before

sending it for servicing.

7. The terms of removing defects depends on the commercial

terms of the Seller.

The Manufacturer is not responsible for untimely servicing of the

Device or for faulty repairs carried out by unauthorized service.

8. When exercising their rights under this warranty, the User

must provide the Device with the following documents: receipt

and valid warranty card with date of purchase.

9. After a warranty repair has been carried out, the warranty

period is extended only for that period.

10. The warranty does cover any damages to the Device NOT

which occur in the following circumstances:

• When the Device has been used or wired inappropriately, in-

cluding inappropriate fuses, overpassing maximal values of load

and current, electric shock, short circuit or other problems in the

power supply, the power grid or the radio network.

• When there is a non-compliance between warranty card and/

or without a purchase receipt, or attempted forgery of these doc-

uments, including (but not limited to) the warranty card or the

documents proving the purchase.

• When there has been a self-repair attempt, (de)installation,

modication, or adaptation of the Device by unauthorized per

sons.

• Intentional or negligent improper handling, storing or trans-

portation of the Device, or in the event of non-observance of the

instructions included in this warranty.

• When a non-standard power supply, network, or faulty Devices

have been used.

• When damages occur which were caused regardless of the

Manufacturer, including but not limited to: oods, storms, re,

lightning, natural disasters, earthquakes, war, civil wars, other

force majeure, unforeseen accidents, robbery, water damage, any

damages made by ingress of liquids, weather conditions, solar

heating, any damages made by intrusion of sand, humidity, high

or low temperature, or air pollution.

• When there are other reasons beyond manufacturing defect, in-

cluding but not limited to: water damage, ingress of liquid into the

Device, weather conditions, solar overheating, intrusion of sand,

humidity, low or high temperature, air pollution.[u1]

• When there have been mechanical damages (forced opening,

breaking, cracks, scratches or deformations) caused by a hit, fall,

or from another object, wrong use, or caused by not following the

instructions for use.

• When damage has been caused by exposing the Device to se-

vere outdoor conditions such as: high humidity, dust, too low or

too high temperature. Terms of proper storage are specied in

the User Manual.

• When damage has been caused by lack of maintenance by the

User, as specied in the User manual.

• When damage has been caused by faulty accessories, or those

not recommended by the Manufacturer.

• When damage has been caused by the use of non-original spare

parts or accessories not suitable for the specied Device mod

el, or after repairs and changes carried out by an unauthorized

service or person.

• When damage has been caused by the use of faulty Devices

and/or accessories.

• When damage has been caused by faulty software, a computer

virus or other harmful behaviour on the Internet, or by lack of

software updates or incorrect updates by a method not provided

by either the Manufacturer or by the Manufacturer’s software.

11. The range of warranty repairs does not include periodical

maintenance and inspections, particularly cleaning, adjustments,

checks, bug xes or program parameters and other activities that

must be performed by the User (Buyer). The warranty does not

cover wear of the Device, because such elements have a limited

lifespan.

12. The Manufacturer is not responsible for any property dam-

age caused by a defect in the Device. The Manufacturer is not

liable for indirect damages (including but not limited to loss of

prots, savings, lost prots, claims by third parties) in connection

with any defect of the Device, nor for any property damage or

personal injury arising out of or related to the use of the Device.

13. The Manufacturer is not responsible for damage caused by

circumstances independent of the Manufacturer, including but

not limited to: oods, storms, re, lightning, natural disasters,

earthquakes, war, civil unrest and other force majeure, unfore-

seen accidents, or theft

Manufacturer: Allterco Robotics EOOD

Address: Soa, 1407, 103 Cherni vrah blvd.

Tel.: +359 2 988 7435

E-mail: support@shelly.cloud

http://www.Shelly.cloud

The Declaration of Conformity is available at:

https://Shelly.cloud/declaration-of-conformity/

Changes in the contact data are published by the Manufac-

turer at the ocial website of the Device:

http://www.Shelly.cloud

The User is obliged to stay informed for any amendments of

these warranty terms before exercising his/her rights against

the Manufacturer.

All rights to trademarks She® and Shelly

® , and other intel-

lectual rights associated with this Device belong to Allterco

Robotics EOOD.

2019/01/v01

You can nd the latest version of the Shelly RGBW2 user guide on

this address: https://shelly.cloud/downloads/

Or by scanning this QR code:

Product specificaties

Merk:	Shelly
Categorie:	Smarth home
Model:	RGBW2
Kleur van het product:	Blue, Yellow
Breedte:	43 mm
Diepte:	38 mm
Hoogte:	14 mm
Soort:	Dimmer
Stroombron:	DC
Connectiviteitstechnologie:	Draadloos
Aantal per verpakking:	1 stuk(s)
Ingangsspanning:	12/24 V
Frequentie:	2400 – 2500 MHz
Aantal kanalen:	4 kanalen
Draadloze technologie:	Wi-Fi
Maximum indoorbereik:	30 m
Maximum outdoorbereik:	50 m
Bedrijfstemperatuur (T-T):	0 - 40 °C
Intelligent aan/uit:	Ja