Sharp RK56S27 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Sharp RK56S27 (4 pagina's) in de categorie Signaalversterker TV. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
For Sharp Carousel® Built-in Kit
Models RK56S27 or RK56S30
S = STAINLESS
THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE
OVENS TO BE INSTALLED ABOVE ANY ELECTRIC WALL OVEN.
PLEASE SEE THE OPERATION MANUAL REGARDING APPROVED
BUILT-IN APPLICATIONS.
IMPORTANT:
This Built-in Kit is designed for and approved only for those
Sharp Microwave Ovens specifying Built-In Kit RK56S27 or
RK56S30. Refer to instruction manual for approved models.
PLEASE READ THESE INSTRUCTIONS
THOROUGHLY
BEFORE BEGINNING INSTALLATION!
Be sure to DISCONNECT THE PLUG of the microwave
oven from the electrical outlet before installing the Built-in
Kit. Remove the Carousel turntable from the oven cavity.
Because the kit includes metal parts, due caution should
be used in handling and installation to avoid the possibil-
ity of injury.
ITEM PART NAME QTY
A FRONT FRAME
RK56S27: FDECAB252MRK0
RK56S30: FDECAB253MRK0
1
B BACK FRAME
RK56S27: FDECAB255MRK0
RK56S30: FDECAB255MRK0
1
C EXHAUST DUCT ASSEMBLY
PDUC-B188MRP0
1
D SCREW D: XTSS740P20000 2
E SCREW E: XOPS740P16000 4
1
INSTALLATION INSTRUCTIONS
A B
D
C
E
V-cut
indicates
center of
duct
CL
2
The opening in the wall or cabinet must be within the
following dimensions:
Cut Out RK56S27 & RK56S30
Height (A) 16
1/4"
Width (B) 261/8" to 26
3/8"
Minimum Depth (C) 20"
Outlet should be in the shaded area as indicated on NOT
Sketch 1.
A
B
4"
C
4"
SKETCH 1
NOTES
Please allow minimum 3" wood gap between the
microwave oven cutout and the appliance cutout below
the microwave oven. See Sketch 2
3" Min.
Microwave cutout
Wall oven cutout
SKETCH 2
If the dimension of DEPTH (C) is more than 21", the outlet
location may be any area on the rear wall.
The oor of the opening should be constructed of plywood
strong enough to support the weight of the oven and oor
load (about 100 pounds). The oor should be level and
90˚ with the face of the cabinet for proper installation and
operation of the oven. Be sure to check the local building
code as it may require that the opening be enclosed with
sides, ceiling and rear partition. The proper functioning of
the oven does not require the enclosure.
STEP 1 CABINET OR WALL OPENING
3
1. Place the EXHAUST DUCT ASSEMBLY in the center of the
opening. Position the front edge of the duct 3/8" proud of
the front edge of the cabinet. See Sketch 3.
2. Mark the two holes, center punch and pre-drill with 1/16"
drill bit. Secure the EXHAUST DUCT ASSEMBLY with two
SCREWS D. See Sketch 3.
STEP 2 EXHAUST DUCT ASSEMBLY INSTALLATION
3/8”
Screw D
Screw D
CL
Exhaust duct assembly,
position 3/8" proud of the
front edge of cabinet
SKETCH 3
1. Place the oven adjacent to the wall or cabinet opening.
Plug the POWER CORD into the electrical outlet.
2. Carefully guide the assembled oven into the prepared
opening. Slide the oven on the EXHAUST DUCT
ASSEMBLY. See Sketch 4. Avoid pinching the cord
between the oven and the wall. Adjust the position of
the oven so that the feet of the oven are tted into the
recesses of the EXHAUST DUCT ASSEMBLY and door
will open properly. See Sketch 5.
SKETCH 4
Exhaust
duct
assembly
Foot
Duct recess
SKETCH 5
STEP 3 FRAME INSTALLATION


Product specificaties

Merk: Sharp
Categorie: Signaalversterker TV
Model: RK56S27

Heb je hulp nodig?

Als je hulp nodig hebt met Sharp RK56S27 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden