Scosche EFX Mono Amplifier Handleiding

Scosche Receiver EFX Mono Amplifier

Lees hieronder de 📖 handleiding in het Nederlandse voor Scosche EFX Mono Amplifier (8 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

500c1/1000c1

1-CHANNEL (MONO) AMPLIFIERS

INSTALLATION MANUAL

EFX AMPLIFIER FEATURES

500c1 SPECIFICATIONS

BEFORE YOU BEGIN:

Read all instructions and Cautions.

Disconnect Negative terminal of Vehicle battery.

Digital Multi-Meter

EFX Amplifier Wiring Kit, EFX REVOPAK4 is

recommended for these amplifiers.

Wire Strippers and Cutters

Drill and Drill Bits

Electrical Tape

Tools & Supplies

Installation procedures:

Plan your installation completely before beginning.

Be sure you have all materials needed to complete your installation.

Please call us with any questions before you start at:

Location/Mounting Amplifier

500c1

- 18dB Adjustable Full/Low Pass

- Electronic Crossover (40Hz~400Hz)

- 2-Ohm Load Capability

1000c1

- 18dB Adjustable Low Pass

- Electronic Crossover (40Hz~200Hz)

- 1-Ohm Load Capability

- Strapable

Power Output: 350 Watts RMS x 1 Channel at 4 Ohms and 1% THD+N

Signal to Noise Ratio: >80 dBA (reference:1 Watt into 4 Ohms)

Additional Power Output: 500 Watts RMS x 1 Channels at 2 Ohms at 1% THD+N

Frequency Response: 20Hz -20kHz (-3dB)

Maximum Input Signal: 6V (Low Level) / 10V (High Level

Minimum Input Signal: 200mV (Low Level) / 420mV (High Level)

1000c1 SPECIFICATIONS

Power Output: 350 Watts RMS x 1 Channel at 4 Ohms and 1% THD+N

Signal to Noise Ratio: >80 dBA (reference:1 Watt into 4 Ohms)

Additional Power Output: 500 Watts RMS x 1 Channels at 2 Ohms at 1% THD+N

1000 Watts RMS x 1 Channels at 1 Ohms at 1% THD+N

Frequency Response: 20Hz -200Hz (-3dB)

Maximum Input Signal: 6V (Low Level) / 10V (High Level)

Minimum Input Signal: 200mV (Low Level) / 420mV (High Level)

- 0-12dB Variable 45Hz Bass Boost

- RCA Line Level Output Loop-Thru

- Line Level & Speaker Level Inputs

- Soft Start Turn-on/off

- 5-Way Protection (Thermal, Short Circuit,

Impedance, Voltage, Reverse Polarity)

- MOSFET Power Switching Transistors

- Brushed Aluminum Heatsink and Top Plate

- Sturdy Aluminum Side Panels

- Illuminated Logo Badge

IMPORTANT/ PRELIMINARY

Select a safe/dry location to mount your Amplifier. Double check location and placement of

your amplifier before making any connections or drilling any holes. Never mount your Amplifier

in the engine compartment, or cover it with carpet or any other fabric materials that will cause

the Amplifier not to get the proper ventilation. Avoid drilling through electrical wires, fuel lines,

or other obstructions that may be around your mounting area. If you have any questions or

concerns, please contact our tech support team at 1-800-621-3695 Ext. 3

IMPORTANT/ PRELIMINARY

ROUTING CABLES AND WIRES

Determine the safest place to run wires through firewall. If it is necessary to drill holes be sure

area is free of any obstructions on either side. Always use a grommet to protect wire.

Be sure to route all wires and cables away from parts that may move or become hot. Excessive

heat will damage the amplifier and wiring. Route power wires away from signal (RCA) cables. If

power wires and signal cables need to intersect cross at a 90% angle. Route RCA cables away

from wires that may carry high current.

WARNING: MAKE SURE YOU CHECK TWICE. DRILLING THROUGH ANY ELECTRICAL

WIRES, FUEL LINES OR ANY OTHER VEHICLE SYSTEMS MAY CAUSE INJURY OR

DEATH.

AMPLIFIER STATUS INDICATOR

LED STATUS INDICATOR

PROT

POWER: GREEN The LED will illuminate in while amplifier is on.

POWER PROTECT: RED The LED will illuminate in to indicate the Amp is in "Protect Mode",

This may be due to an overload or circuit problem (See page 7-8 for trouble shooting tips).

- 2 -

MONO HI GH PO WER CLA SS-D AM PL IFIER

PROT

GND

POWER

B REM PHASE HI INPUT

GND

L R

REMOTE

MASTER/SLAVE

SLAVE MASTER

LEVEL

MAXMIN

BASS

12dB0dB

LOW PASS

200Hz40Hz0 180

OUT

LOW

INPUT

LINE

OUTPUT

SPEAKER

AMPLIFIER ADJUSTMENTS

Level:

The Level Adjust Control (Gain) matches the output of your Car Stereo to the

inputs on the Amplifier.

1. Turn Stereo on and adjust the volume to about 3/4’s of the stereo’s

maximum volume.

2. Carefully turn the Level control up (by turning it clockwise from the "Min"

position) on the Amp until the sound is just above your normal listening

volume or near distortion. (Distortion is when the sound/ music becomes

garbled, breaks up, or unclear).

4. If there is excessive HUM or HISS between songs, the levels are set TOO

HIGH and should be turned down, (reverse towards "Min").

Low Level Inputs:

Low Level (RCA) inputs. Using the Low Level output from your car stereo is

recommended (if available). If no Low Level Outputs are available from

your car stereo, please see the HIGH LEVEL INPUT on page 6.

Low Level Outputs:

The Line Level Output is to be used as an easy solution to link multiple

amplifiers together without the use of RCA Y-cables or running extra RCA

cables from the front of the vehicle to the rear amplifier location.

Bass Boost:

Adjustable Bass Boost (0~ +12dB @ 45Hz)

Use Caution while adjusting Bass Boost. Using to high of a setting may

cause distortion or damage Speakers.

MIN MAX

0dB 12dB

- 3 -

PHASE

REMOTE

MASTER/SLAVE

0 180

OUT

LOW PASS

200Hz40HzFULL

GND

L R

HI INPUT

Use the High Level input harness if you are connecting your amplifier to a

Factory Stereo or a Stereo that does not have any available Low-Level (RCA)

outputs. Connect Left and Right Speaker outputs from the vehicle to the Left

and Right High Level input wires.

High Input Harness:

Low Pass Filter:

Remote Level Control:

Master/ Slave In and Outputs:

Phase Level:

Plug the cable into the REM connector on the amplifier and into the controller.

This will allow you to adjust the level of your amplifier while in low filter mode

from the crossover frequency and below.

Use the Low Pass filter when you want to Filter out high frequencies.

Set the switch to Low Pass and adjust the level to the desired frequency.

The Master and Slave settings on the 1000c1 allow you to “Strap” or

compound (2) amplifiers to a drive a Single voice coil based on your specific

needs and power requirements. The default setting is for Master. If you

choose to Slave a second amp, please see page 6.

Adjusts the relative phase of the output in a range of 0 to - 180 degrees.

Product specificaties

Merk:	Scosche
Categorie:	Receiver
Model:	EFX Mono Amplifier
Kleur van het product:	Aluminium
Bluetooth:	Nee
Connectiviteitstechnologie:	Bedraad
HDMI:	Nee
PC-ingang (D-Sub):	Nee
Uitgangsvermogen:	800 W
Impedantie:	4 Ohm
Aantal kanalen:	1 kanalen