Schneider MTN644492 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Schneider MTN644492 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
The binary input REG-K/4x10 is used to connect four
floating contacts, push-buttons or switches to the KNX
bus.
The binary input makes a contact supply voltage (SELV)
available which is electrically isolated from the bus
voltage. A power supply is thus not necessary for the
connected floating contacts.
The binary input has a bus coupler. It is installed on a
DIN rail acc. to EN 60715, with the bus connection
made via a bus connecting terminal. A data rail is not
required.
For your safety
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH
Safe electrical installation must be carried out only by
skilled professionals. Skilled professionals must prove
profound knowledge in the following areas:
Connecting to installation networks
Connecting several electrical devices
Laying electric cables
Connecting and establishing KNX networks
Safety standards, local wiring rules and regulations
Failure to follow these instructions will result in
death or serious injury.
The device may be damaged!
Never connect the device to an external power
source.
The binary input circuits must comply with the safety
extra-low voltage conditions (SELV) in accordance
with IEC 60364-4-41.
Only operate the device according to the specifica-
tions stated in the Technical data.
All the devices that are installed next to the binary in-
put must be equipped with basic insulation at the very
least.
Failure to follow these instruction can result in
equipment damage.
Binary input introduction
ACover of the bus connecting terminal
BProgramming button and programming LED (behind
hinged cover)
COperational LED
DChannel status LEDs
1Set the binary input onto the DIN rail.
2Connect KNX.
¼
WARNING
Risk of fatal injury from electrical current.
The device could be damaged.
Safety clearance must be guaranteed in
accordance with IEC 60664-1. There must be at
least 4 mm between the individual cores of the
230 V supply cable and the KNX line.
3Connect the input cables.
When the bus voltage is connected and there is a signal
at the input, the corresponding yellow channel status
LED will light up.
|An installation with Y bell wire or J-FY flat
webbed bell wire is permitted.
Operating and display elements
Installing the binary input
E1 0V E2 E3 0V E4
E 4E 2 RUNE 1 E 3
A
B
C
D
1
2
1 2
34
5 mm
230 V
4 mm
KNX
KNX
+ -
E2
E3
E4
E1
Uk0V
0V
1Press the programming button.
The programming LED lights up.
2Load the physical address and the application into
the device from the ETS.
The operating LED lights up: The application was loaded
successfully, the device is ready for operation.
Schneider Electric Industries SAS
35 rue Joseph Monier
Rueil Malmaison 92500
France
If you have technical questions, please contact the Cus-
tomer Care Centre in your country.
se.com/contact
Putting the binary input into operation
Technical data
Supply from KNX: DC 24 V / max.18 mA
Insulation voltage: AC 4 kV bus/inputs
Inputs
Contact voltage: max. 10 V (SELV)
Contact current: max. 2 mA, pulsating
Transfer resistance
(between contact and
cable):
max. 500 when contact
closed,
min. 50 k when contact
open
Permitted cable
length: max. 50 m
Ambient temperature
Operation: -5 °C to +45 °C
Storage: -25 °C to +55 °C
Transport: -25 °C to +70 °C
Max. humidity: 93 % relative humidity, no
moisture condensation
Environment: The device is designed for use
at a height of up to 2000 m
above sea level (MSL).
Connections
Inputs, outputs: Screw terminals
Single-core: 1.5 mm2 to 2.5 mm2
Finely stranded
(with core end sleeve): 1.5 mm2 to 2.5 mm2
KNX: Bus connecting terminal
Dimensions
Height x width x
depth: 90 x 45 x 65 mm
Device width: 2.5 modules
Schneider Electric -Contact
Schneider Electric Limited
Telford, TF3 3 BL, UK
UK Representative
Stafford Park 5
SpaceLogic KNX Binary input REG-K/4x10
Operating instructions
Art. no. MTN644492
en
E 4E 2 RUNE 1 E 3
V6444-562-01 11/21


Product specificaties

Merk: Schneider
Categorie: Niet gecategoriseerd
Model: MTN644492

Heb je hulp nodig?

Als je hulp nodig hebt met Schneider MTN644492 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Schneider

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd